Nissan Juke (2014 year). Service Repair Manual — part 209
SE-16
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
PIIB8742E
Revision: 2013 October
2014 JUKE
FRONT SEAT
SE-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REMOVAL AND INSTALLATION
FRONT SEAT
Exploded View
INFOID:0000000009753904
DRIVER SEAT
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback assembly
(with heater seat only)
5.
Inner lower cover
6.
Seatback trim
(without heater seat only)
JMJIA4582GB
Revision: 2013 October
2014 JUKE
SE-18
< REMOVAL AND INSTALLATION >
FRONT SEAT
PASSENGER SEAT
7.
Seatback pad
(without heater seat only)
8.
Seat belt buckle
9.
Anchor bolt
10. Seat cushion inner finisher
11.
Reclining device inner cover (front)
12. Reclining device inner cover (rear)
13. TORX bolt
14. Seat cushion trim
(without heater seat only)
15. Seat cushion pad
(without heater seat only)
16. Seat cushion silencer
17. Seat cushion assembly
(with heater seat only)
18. Lifter link
19. Lifter lever knob
20. Lifter lever knob cap
21. Reclining lever knob
22. Seat cushion outer finisher
23. Spring
24. Reclining device outer cover (front)
25. Reclining device outer cover (rear)
26. Outer lower cover
27. Side air bag module
28. Seatback silencer
29. Seat frame & adjuster assembly
: Pawl
: Metal clip
: Do not reuse
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
Revision: 2013 October
2014 JUKE
FRONT SEAT
SE-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback silencer
5.
Side air bag module
6.
Spring
7.
Reclining device outer cover (rear)
8.
Reclining device outer cover (front)
9.
Seat cushion outer finisher
10. Reclining lever knob
11.
TORX bolt
12. Seat cushion trim
(without heater seat only)
13. Seat cushion pad
(without heater seat only)
14. Occupant detection system control
unit
15. Seat cushion silencer
16. Seat cushion assembly
(with heater seat only)
17. Anchor bolt
18. Seat belt buckle
19. Seat cushion inner finisher
20. Reclining device inner cover (front)
21. Reclining device inner cover (rear)
JMJIA9479GB
Revision: 2013 October
2014 JUKE
SE-20
< REMOVAL AND INSTALLATION >
FRONT SEAT
Removal and Installation
INFOID:0000000009753905
REMOVAL
CAUTION:
Before servicing, disconnect the battery cable from negative terminal or remove the fuse.
1.
Remove headrest.
2.
Set the seatback vertically.
3.
Slide seat to the frontmost position.
4.
Remove rear outer mounting TORX bolt.
5.
Remove rear inner mounting TORX bolt.
6.
Slide seat to the rearmost position.
7.
Remove front outer mounting TORX bolt.
8.
Remove front inner mounting TORX bolt.
9.
Remove seat cushion lower harness connectors and harness fixing clamps.
CAUTION:
Before performing removal operation, check the installation position of harness connectors and
harness fixing clamps.
10. Remove seat from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• When installing, tighten mounting TORX bolts according to
the numerical order (1, 2, 3, and 4 as shown in the figure),
starting from front inner mounting TORX bolt.
• Always fix the harness fixing clamp in position.
SEATBACK
SEATBACK : Disassembly and Assembly
INFOID:0000000009753906
DISASSEMBLY
CAUTION:
22. Seatback pad
(without heater seat only)
23. Seatback trim
(without heater seat only)
24. Seatback assembly
(with heater seat only)
25. Seat frame & adjuster assembly
: Pawl
: Metal clip
: Do not reuse
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMJIA4591ZZ
Revision: 2013 October
2014 JUKE
FRONT SEAT
SE-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
For models with heater seat, always replace heater seat as a seatback assembly without disassem-
bling trim and pad.
1.
Remove seatback retainer installed in the lower portion of seat cushion.
2.
Remove harness installed in the lower portion of seat cushion.
1.
Disconnect seatback heater unit harness connector
(A).(with heater seat only.)
2.
Remove seatback heater unit harness connector fixing clips
(A) and harness fixing clamp (B). (with heater seat only)
3.
Remove side air bag module harness connector fixing clips
(C) and harness fixing clamp (D).
3.
Open seatback fastener (A) and remove seatback retainer (B).
4.
Remove side air bag module harness fixing clamps from seat frame & adjuster assembly.
5.
Use pincers, etc., to press up pawls as shown by the arrows in
the figure, and remove headrest holder from seatback.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
6.
Remove side air bag module mounting nuts.
7.
Remove seatback trim and seatback pad from seat frame & adjuster assembly.
CAUTION:
Never subject side air bag module to impact by dropping or hitting.
8.
Remove side air bag module from seatback pad.
9.
Separate the seatback trim and seatback pad. (without heater seat only)
Remove hog rings, and separate the seatback trim and seatback pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
10. Remove seatback silencer from seat frame & adjuster assembly.
ASSEMBLY
Note the following, and assemble in the reverse order of disassembly.
CAUTION:
Always install the hog ring in position.
SEAT CUSHION
: Vehicle front
JMJIA4602ZZ
JMJIA4363ZZ
PIIB4084J
Revision: 2013 October
2014 JUKE
SE-22
< REMOVAL AND INSTALLATION >
FRONT SEAT
SEAT CUSHION : Disassembly and Assembly
INFOID:0000000009753907
DISASSEMBLY
CAUTION:
For models with heater seat, always replace heater seat as a seat cushion assembly without disas-
sembling trim and pad.
1.
Remove seat cushion outer finisher.
1.
Disengage pawls and remove lifter lever knob cap (1).
(Driver seat only)
2.
Remove fixing screws and remove lifter lever knob (2).
(Driver seat only)
3.
Disengage pawl using a screwdriver while pulling reclining
lever knob. Slide reclining lever knob toward seat front and
remove it.
4.
Pull seat cushion outer finisher toward seat front. Disengage pawls and metal clips. Slide seat cush-
ion outer finisher toward seat front. Remove seat cushion outer finisher.
2.
Remove harness installed in the lower portion of seat cushion.
: Pawl
JMJIA4592ZZ
: Pawl
JMJIA4593ZZ
1.
Seat cushion outer finisher
(Driver seat)
2.
Seat cushion outer finisher
(Passenger seat)
: Pawl
: Metal clip
JMJIA4594ZZ
Revision: 2013 October
2014 JUKE
FRONT SEAT
SE-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Disconnect seat cushion heater unit harness connector (A).
(with heater seat only)
2.
Remove seat cushion heater unit harness connector fixing
clip (B) and harness fixing clamps (C). (with heater seat
only)
3.
Remove seat belt buckle harness connector fixing clip (D)
and harness fixing clamps (E).
3.
Remove seat cushion inner finisher.
1.
Remove harness fixing clamp of seat belt buckle installed on seat frame & adjuster assembly.
2.
Remove seat belt buckle mounting anchor bolt, and then remove seat belt buckle from seat frame
&adjuster assembly.
3.
Pull seat cushion inner finisher forward. Disengage pawls
and metal clips.
4.
Remove seat cushion retainer from seat frame & adjuster assembly. Remove seat cushion trim and seat
cushion pad.
5.
Remove hog rings, and separate the seat cushion trim and seat cushion pad. (without heater seat only)
CAUTION:
Before performing separating operation, check the installation position of hog rings.
6.
Remove seat cushion silencer from seat frame & adjuster assembly.
7.
Remove seatback trim and seatback pad from seat frame & adjuster assembly.
Refer to
SE-20, "SEATBACK : Disassembly and Assembly"
.
8.
Remove reclining device cover.
• Remove fixing screw, and then remove reclining device outer cover (front and rear).
• Remove fixing screw, and then remove reclining device inner cover (front and rear).
9.
Remove following parts from seat frame & adjuster assembly.
• Remove reclining spring.
• Remove fixing screws. Pull outer lower cover toward seat outer. Disengage metal clips. Remove outer
lower cover. (driver seat only)
• Remove fixing screws, and then remove inner lower cover. (driver seat only)
• Remove occupant detection system control unit. Refer to
SR-31, "Removal and Installation"
.
ASSEMBLY
Note the following, and assemble in the reverse order of disassembly.
CAUTION:
• Always install the hog rings in position.
: Vehicle front
JMJIA4603ZZ
: Pawl
: Metal clip
JMJIA4595ZZ
Revision: 2013 October
2014 JUKE
SE-24
< REMOVAL AND INSTALLATION >
FRONT SEAT
• When installing seat cushion finisher, always slide seat cush-
ion outer finisher toward seat rear, engage portion (A) of seat
frame & adjuster assembly and portion (B) of seat cushion
outer finisher, and then install pawls and metal clips of seat
cushion outer finisher.
: Vehicle front
JMJIA4612ZZ
Revision: 2013 October
2014 JUKE
REAR SEAT
SE-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REAR SEAT
Exploded View
INFOID:0000000009753908
2WD models
JMJIA5194GB
1.
Headrest
2.
Headrest holder (free)
3.
Headrest holder (locked)
4.
Seatback trim RH
5.
Seatback pad RH
6.
Seat lock cover RH
Revision: 2013 October
2014 JUKE
SE-26
< REMOVAL AND INSTALLATION >
REAR SEAT
7.
Seatback lock knob
8.
Seatback lock knob finisher
9.
Seatback lock assembly RH
10. Side hinge
11.
Bush
12. Spacer
13. Lock washer
14. Striker RH
15. Seat cushion hook
16. Seat cushion pad
17. Seat cushion trim
18. Striker LH
19. Seatback lock assembly LH
20. Seat lock cover LH
21. Seatback pad LH
22. Seatback trim LH
23. Seatback silencer LH
24. Seatback silencer RH
25. Seatback tether cover
26. Center seat belt finisher
27. Center hinge
28. Center seat belt
29. Seat belt buckle
30. Seatback frame RH
31. Seatback frame LH
: Pawl
: Metal clip
: N·m (kg-m, ft-lb)
Revision: 2013 October
2014 JUKE
REAR SEAT
SE-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
AWD models
JMJIA5193GB
1.
Headrest
2.
Headrest holder (free)
3.
Headrest holder (locked)
4.
Seatback trim RH
5.
Seatback pad RH
6.
Seat lock cover RH
7.
Seatback lock knob
8.
Seatback lock knob finisher
9.
Seatback lock assembly RH
10. Side hinge
11.
Bush
12. Spacer
13. Lock washer
14. Striker RH
15. Seat cushion hook
16. Seat cushion pad
17. Seat cushion trim
18. Striker LH
Revision: 2013 October
2014 JUKE
SE-28
< REMOVAL AND INSTALLATION >
REAR SEAT
SEAT CUSHION
SEAT CUSHION : Removal and Installation
INFOID:0000000009753909
REMOVAL
1.
Lift up seat cushion at a close position (B) of engaging portion (A) and disengage seat cushion hook.
CAUTION:
Seat cushion wire close to engaging portion deforms, if excessive force is applied to seat cushion
front end when removing seat cushion.
To avoid the deformation, be careful to remove seat cushion while applying force to close posi-
tion, as much as possible, of engaging portion.
2.
Pull out seat belt buckle from seat cushion.
3.
Remove seat cushion from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
SEAT CUSHION : Disassembly and Assembly
INFOID:0000000009753910
DISASSEMBLY
Remove hog rings, and separate the seat cushion trim and seat cushion pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
ASSEMBLY
Note the following item, and assemble in the reverse order of disassembly.
CAUTION:
Always install the hog ring in position.
SEATBACK
19. Seatback lock assembly LH
20. Seat lock cover LH
21. Seatback pad LH
22. Seatback trim LH
23. Seatback silencer LH
24. Seatback silencer RH
25. Seatback tether cover
26. Center seat belt finisher
27. Center hinge
28. Center seat belt
29. Seat belt buckle
30. Seatback frame RH
31. Seatback frame LH
: Pawl
: Metal clip
: N·m (kg-m, ft-lb)
: Vehicle front
JMJIA4835ZZ
Revision: 2013 October
2014 JUKE
REAR SEAT
SE-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
SEATBACK : Removal and Installation
INFOID:0000000009753911
LH SIDE SEATBACK
Removal
CAUTION:
Remove seatback with seat cushion installed.
1.
Temporarily move seat cushion to the position where center anchor of center seat belts can be removed.
2.
Remove center anchor mounting bolt of center seat belt. Remove center anchor.
3.
Return seat cushion to the normal position.
4.
Unlock seatback lock assembly. Tilt seatback toward vehicle front. Remove headrests.
5.
Fold seatback toward vehicle front.
6.
Pull up seatback carpet (A). Remove mounting bolts (B) of seat-
back hinge portion.
7.
Remove seatback from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
Installation
Note the following items, and install in the reverse order of removal.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• Install seat cushion to the vehicle, and then install seatback.
• Temporarily tighten bolts, fold up seatback, check that lock and striker do not interfere, and then
tighten bolts.
• When installing seatback, tighten mounting bolts according to
the numerical order (1, 2, 3, and 4 as shown in the figure).
RH SIDE SEATBACK
Removal
CAUTION:
Remove seatback with seat cushion installed.
1.
Unlock seatback lock assembly. Tilt seatback toward vehicle front. Remove headrests.
2.
Fold seatback toward vehicle front.
JMJIA4836ZZ
JMJIA4837ZZ
Revision: 2013 October
2014 JUKE
SE-30
< REMOVAL AND INSTALLATION >
REAR SEAT
3.
Pull up seatback carpet (A). Remove mounting bolts (B) of seat-
back hinge portion.
4.
Remove seatback from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
Installation
Note the following items, and install in the reverse order of removal.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• Install seat cushion to the vehicle, and then install seatback.
• Temporarily tighten bolts, fold up seatback, check that lock and striker do not interfere, and then
tighten bolts.
• When installing seatback, tighten mounting bolts according to
the numerical order (1, 2, 3, and 4 as shown in the figure).
SEATBACK : Disassembly and Assembly
INFOID:0000000009753912
DISASSEMBLY
LH side seatback
1.
Remove headrest holder.
1.
Pull seat lock cover in direction indicated by the arrow as
shown in the figure. Remove seat lock cover.
JMJIA4838ZZ
JMJIA4839ZZ
: Metal clip
JMJIA4372ZZ
Revision: 2013 October
2014 JUKE
REAR SEAT
SE-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
2.
Pull tether cover in direction indicated by the arrow as
shown in the figure. Remove tether cover.
3.
Open seatback fastener (A) and remove seatback retainer
(B).
4.
Use pincers, etc., to press up pawls as shown by the arrows
in the figure, and remove headrest holder from seatback.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
2.
Remove seatback lock knob finisher.
1.
Rotate seatback lock knob counterclockwise. Remove seat-
back lock knob.
: Pawl
JMJIA4611ZZ
JMJIA4371ZZ
PIIB4084J
JMJIA4374ZZ
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст