Nissan Juke (2014 year). Service Repair Manual — part 227
B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT
SRC-39
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000009751725
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751726
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1011
B1012
B1013
B1014
B1015
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
SRC-40
< DTC/CIRCUIT DIAGNOSIS >
B1017, B1020, B1021 OCCUPANT SENS C/U
B1017, B1020, B1021 OCCUPANT SENS C/U
DTC Logic
INFOID:0000000009751727
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751728
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT
1.
Replace occupant detection system control unit. Refer to
SR-31, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE OCCUPANT DETECTION SYSTEM SEAT SENSOR
1.
Replace passenger seat cushion frame. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1017
B1020
B1021
OCCUPANT SENS C/
U
[UNIT FAIL]
Trouble occurs in Occupant Detection
System control unit
• Disconnection of wiring harness
• Malfunction in Occupant Detection System
control unit
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
B1017, B1020, B1021 OCCUPANT SENS C/U
SRC-41
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
SRC-42
< DTC/CIRCUIT DIAGNOSIS >
B1018 OCCUPANT SENS
B1018 OCCUPANT SENS
DTC Logic
INFOID:0000000009751729
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751730
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT
1.
Replace occupant detection system control unit. Refer to
SR-31, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE OCCUPANT DETECTION SYSTEM SEAT SENSOR
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1018
OCCUPANT SENS
[UNIT FAIL]
Malfunction occurs in Occupant Detection
System seat sensor
• Disconnection of wiring harness
• Malfunction in Occupant Detection System
seat sensor
• Malfunction in Occupant Detection System
control unit
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
B1018 OCCUPANT SENS
SRC-43
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
1.
Replace passenger seat cushion frame. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
SRC-44
< DTC/CIRCUIT DIAGNOSIS >
B1022 OCCUPANT SENS C/U
B1022 OCCUPANT SENS C/U
DTC Logic
INFOID:0000000009751731
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751732
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT
1.
Replace occupant detection system control unit. Refer to
SR-31, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE OCCUPANT DETECTION SYSTEM SEAT SENSOR
1.
Replace passenger seat cushion frame. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1022
OCCUPANT SENS
C/U
[COMM FAIL]
Malfunction occurs in Occupant Detection Sys-
tem control unit, circuit of Occupant Detection
System control unit-Air bag diagnosis sensor unit
or Air bag diagnosis sensor unit
• Disconnection of wiring harness
• Malfunction in Occupant Detection System
control unit
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
B1022 OCCUPANT SENS C/U
SRC-45
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
SRC-46
< DTC/CIRCUIT DIAGNOSIS >
B1023 PASSENGER AIR BAG OFF INDICATOR
B1023 PASSENGER AIR BAG OFF INDICATOR
DTC Logic
INFOID:0000000009751733
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751734
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK PASSENGER AIR BAG OFF INDICATOR
1.
Replace cluster lid C (passenger air bag OFF indicator).
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1023
PASS A/B INDCTR CKT
[UNIT FAIL]
Passenger air bag OFF indicator circuit
is open or shorted to ground or the cir-
cuits are shorted each other
• Harness or connectors
• Malfunction in passenger air bag OFF indicator
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
B1023 PASSENGER AIR BAG OFF INDICATOR
SRC-47
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
SRC-48
< DTC/CIRCUIT DIAGNOSIS >
B1025, B1032, B1048 OCS SENSOR
B1025, B1032, B1048 OCS SENSOR
Description
INFOID:0000000009751735
Suppresses the deployment of front passenger air bag when the condition of passenger seat is empty or occu-
pied with a child and child-seat. Also illuminates front passenger air bag OFF indicator lamp when the condi-
tion of passenger seat is occupied with a child-seat and child. In case of malfunction the blinking of the air bag
warning lamp reports the malfunction to driver, and by the on board self-diagnosis system or CONSULT can
detect the cause.
OPERATION
This unit classifies occupant in passenger seat and detects electrical malfunction in Occupant Detection Sys-
tem and transmits malfunction information to air bag control unit.
STRUCTURE
It is integrated into the seat sensor mat and detects the occupants and Occupant Detection System control
unit that classifies the occupants.
INSTALLATION
Occupant Detection System control unit is installed in the passenger seat cushion.
DTC Logic
INFOID:0000000009751736
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “AIR BAG” Self Diagnostic Result CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
NOTE:
SRS does not enter diagnosis mode if no malfunction is detected in user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751737
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1025
B1032
B1048
OCS SENSOR
Malfunction occurs in Occupant Detection Sys-
tem control unit, circuit of Occupant Detection
System control unit-Air bag diagnosis sensor
unit or Air bag diagnosis sensor unit
• Disconnection of wiring harness
• Internal breakdown in Occupant Detection
System control unit
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
B1025, B1032, B1048 OCS SENSOR
SRC-49
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT
1.
Replace occupant detection system control unit. Refer to
SR-31, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE OCCUPANT DETECTION SYSTEM SEAT SENSOR
1.
Replace passenger seat cushion frame. Refer to
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
SRC-50
< DTC/CIRCUIT DIAGNOSIS >
B1026, B1027, B1028, B1029, B1030, B1031 DIAGNOSIS SENSOR UNIT
B1026, B1027, B1028, B1029, B1030, B1031 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000009751738
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751739
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1026
B1027
B1028
B1029
B1030
B1031
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
B1033, B1034 CRASH ZONE SENSOR
SRC-51
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1033, B1034 CRASH ZONE SENSOR
DTC Logic
INFOID:0000000009751740
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751741
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE CRASH ZONE SENSOR
1.
Replace crash zone sensor. Refer to
SR-23, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1033
B1034
CRASH ZONE SEN
[UNIT FAIL]
Crash zone sensor is malfunctioning
• Harness or connectors
• Malfunction in crash zone sensor
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
SRC-52
< DTC/CIRCUIT DIAGNOSIS >
B1033, B1034 CRASH ZONE SENSOR
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
B1035 CRASH ZONE SENSOR
SRC-53
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1035 CRASH ZONE SENSOR
DTC Logic
INFOID:0000000009751742
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751743
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE CRASH ZONE SENSOR
1.
Replace crash zone sensor. Refer to
SR-23, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1035
CRASH ZONE SEN
[COMM FAIL]
Crash zone sensor is malfunctioning or out of
the specified specification
• Harness or connectors
• Malfunction in crash zone sensor
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
SRC-54
< DTC/CIRCUIT DIAGNOSIS >
B1035 CRASH ZONE SENSOR
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст