Nissan Juke (2014 year). Service Repair Manual — part 164
IP-12
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
REMOVAL AND INSTALLATION
INSTRUMENT PANEL ASSEMBLY
Exploded View
INFOID:0000000009750202
JSJIA0096GB
Revision: 2013 October
2014 JUKE
INSTRUMENT PANEL ASSEMBLY
IP-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Removal and Installation
INFOID:0000000009750203
WORK STEP
When removing instrument panel assembly, combination meter, audio unit, NAVI C/U, or center console
assembly take steps in the order shown by the numbers below.
1.
Front passenger air bag module
2.
Instrument panel assembly
3.
Instrument side finisher LH
4.
Combination meter
5.
Cluster lid A
6.
Push-button ignition switch
7.
Steering column upper cover (with-
out Intelligent Key)
8.
Steering column lower cover (without
Intelligent Key)
9.
Multi display unit
10. Instrument lower cover LH
11.
Instrument lower cover RH
12. Glove box lid
13. Glove box dumper
14. Glove box assembly
15. Illumination lamp
16. Socket and bulb
17. Instrument side finisher RH
18. Switch panel
19. Sunload sensor
20. Optical sensor
21. Hazard switch
22. Instrument lower panel LH
23. Audio unit or AV C/U
24. Steering lock escutcheon (without In-
telligent Key)
25. Steering column mask (with Intelli-
gent Key)
26. Cluster lid C
27. Warning lamp
28. Socket knob
29. Inner socket
30. Socket ring
31. Cluster tray
32. USB connector
33. A/C controller (manual A/C)
34. A/C finisher (manual A/C)
35. Knob
36. Steering column upper cover (with
Intelligent Key)
37. Steering column LH cover (with Intel-
ligent Key)
38. Steering column lower cover (with In-
telligent Key)
39. Steering column RH cover (with In-
telligent Key)
: Clip
: Pawl
: Metal clip
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
,
: Indicates that the part is connected at points with same symbol in actual vehicle.
PARTS
INSTRUMENT
PANEL
ASSEMBLY
COMBINATION
METER
AUDIO UNIT
or
NAVI C/U
CENTER
CONSOLE
ASSEMBLY
Shift lever knob (MT models only)
[1]
[1]
Console finisher assembly
[2]
[2]
Console rear finisher
[3]
[3]
Center console assembly fixing screws (rear side)
[4]
[4]
Instrument lower cover LH
[5]
[5]
Instrument lower cover RH
[6]
[6]
Center console assembly
[7]
[7]
Front body side welt LH
[8]
Front pillar garnish LH
[9]
Instrument side finisher LH
[10]
Instrument lower panel LH
[11]
[1]
Driver air bag module
[12]
Steering wheel assembly
[13]
Steering column covers
[14]
Spiral cable
[15]
Combination switch
[16]
Revision: 2013 October
2014 JUKE
IP-14
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
[]: Number indicates step in removal procedure.
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.
REMOVAL
CAUTION:
When removing, always use a remover tool that is made of plastic.
1.
Remove shift lever knob (MT models only). Refer to
TM-21, "Removal and Installation"
2.
Remove console finisher assembly.
1.
Put selector lever in “N” position.
2.
Loosen the parking brake lever stroke by turning the adjusting nut with a socket wrench. Refer to
3, "Inspection and Adjustment"
.
3.
Lift up console finisher assembly in numerical order shown in the figure and disengage metal clips.
4.
Remove console finisher assembly while pulling it towards vehicle rear.
Cluster lid A
[17]
[2]
Combination meter
[18]
[3]
Multi display unit (with auto A/C) or A/C finisher
(with manual A/C)
[19]
[1]
A/C control fixing screws (with manual A/C)
[20]
Cluster lid C
[21]
[2]
Audio unit or AV C/U
[22]
[3]
Harness connector of hazard switch
[23]
Cluster tray
[24]
Front body side welt RH
[25]
Front pillar garnish RH
[26]
Instrument side finisher RH
[27]
Glove box lid
[28]
Glove box assembly
[29]
Passenger air bag module
[30]
Switch panel
[31]
Instrument panel assembly
[32]
Revision: 2013 October
2014 JUKE
INSTRUMENT PANEL ASSEMBLY
IP-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
CAUTION:
• Be careful not for damaging parts in surrounding area.
• Remove metal clips slowly so that they are not damaged.
5.
Disconnect seat heated switch harness connectors (with seat heated switch).
3.
Remove console rear finisher.
1.
Put front seat assembly (LH and RH) to frontmost position.
2.
Pull back console rear finisher, and disengage the pawls
and metal clips.
4.
Remove center console assembly fixing screws (A).
5.
Remove instrument lower cover LH.
1.
Put front seat assembly LH to rearmost position.
: Metal clip
JSJIA0057ZZ
: Pawl
: Metal clip
JMJIA4183ZZ
JMJIA4202ZZ
Revision: 2013 October
2014 JUKE
IP-16
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
2.
Remove fixing clip (A).
3.
Pull the instrument lower cover LH crosswise, and disen-
gage the pawl and metal clips.
CAUTION:
Remove pawl and metal clips slowly so that they are not
damaged.
6.
Remove instrument lower cover RH.
1.
Put front seat assembly RH to rearmost position.
2.
Remove fixing clip (A).
3.
Pull the instrument lower cover RH crosswise, and disen-
gage the pawl and metal clips.
CAUTION:
Remove pawl and metal clips slowly so that they are not
damaged.
7.
Remove center console assembly.
1.
Remove center console fixing screws (A).
2.
Remove seat heated switch harness clip (with seat heated switch).
3.
Lift up center console assembly back side.
CAUTION:
Be careful not for damaging parts in surrounding area.
8.
Release front pillar portion of front body side welt LH. Refer to
INT-21, "BODY SIDE WELT : Removal and
.
9.
Remove front pillar garnish LH. Refer to
INT-18, "FRONT PILLAR GARNISH : Removal and Installation"
.
10. Remove instrument side finisher LH.
1.
Insert remover tool (A) between instrument side finisher LH
and instrument panel assembly to disengage the pawls as
shown in the figure.
2.
Pull back instrument side finisher LH.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
11. Remove instrument lower panel LH.
: Pawl
: Metal clip
JMJIA4551ZZ
: Pawl
: Metal clip
JMJIA4552ZZ
JMJIA4553ZZ
: Pawl
JMJIA4554ZZ
Revision: 2013 October
2014 JUKE
INSTRUMENT PANEL ASSEMBLY
IP-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
1.
Remove hood opener and fuel lid opener lever. Refer to
DLK-158, "HOOD LOCK CONTROL CABLE
(with Intelligent Key System) or
DLK-280, "HOOD LOCK : Removal and
(without Intelligent Key System).
2.
Remove fixing screw (A).
3.
Pull back instrument lower panel LH, and then disengage
the pawls and metal clips.
4.
Disconnect harness connectors and aspirator duct.
12. Remove driver air bag module. Refer to
SR-11, "Removal and Installation"
.
13. Remove steering wheel. Refer to
ST-9, "Removal and Installation"
14. Remove steering column covers.
1.
Place the tilt to the lowest level.
2.
Remove steering lock escutcheon (1). (without Intelligent
Key)
3.
Remove fixing screws (A).
4.
Pull up steering column upper cover (2), and then disen-
gage steering column upper cover fixing pawls.
5.
Remove steering column upper cover.
6.
Pull down the steering column lower cover (3), and then
remove steering column lower cover.
NOTE:
Disengage the pawls, and then remove steering lock escutch-
eon (4). (with Intelligent Key)
15. Remove spiral cable. Refer to
SR-14, "Removal and Installation"
.
16. Remove combination switch. Refer to
BCS-91, "Removal and Installation"
(with Intelligent Key System) or
BCS-158, "Removal and Installation"
(with Intelligent Key System).
17. Remove cluster lid A.
1.
Cover steering shaft with a shop cloth (A) to prevent dam-
age.
2.
Pull back cluster lid A while holding the lower side and dis-
engage the metal clips underside.
3.
Hold both upper sides of cluster lid A and pull it out towards
vehicle rear, and disengage pawl and metal clips topside.
4.
Disconnect push-button ignition switch harness connector
and NATS antenna amp.harness connector. (with Intelligent
Key)
CAUTION:
Remove metal clips slowly so that they are not damaged.
18. Remove combination meter. Refer to
MWI-61, "Removal and Installation"
: Pawl
: Metal clip
JMJIA4556ZZ
: Pawl
JMJIA4189ZZ
: Pawl
: Metal clip
JMJIA4557ZZ
Revision: 2013 October
2014 JUKE
IP-18
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
19. Remove multi display unit (with auto A/C) or A/C finisher (with manual A/C).
Multi display unit (with auto A/C)
1.
Apply protective tape (B) on instrument panel assembly (2) to protect it from damage.
2.
Insert a remover tool (A) into the cutouts at the bottom of
multi display unit (1), then pull straight back to disengage
the pawls and metals clips.
3.
Pull back multi display unit, and then disconnect harness connector.
A/C finisher (with manual A/C)
1.
Apply a protective tape (B) on instrument panel assembly (5) to protect it from damage.
1.
Multi display unit (with auto A/C)
2.
Instrument panel assembly
(with auto A/C models)
3.
Intake door lever knob
4.
A/C finisher (with manual A/C)
5.
Instrument panel assembly
(with manual A/C models)
: Pawl
: Metal clip
: Pawl
: Metal clip
JMJIA4558ZZ
JMJIA6909ZZ
Revision: 2013 October
2014 JUKE
INSTRUMENT PANEL ASSEMBLY
IP-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
2.
Hold intake door lever knob (1) from upper side and lower
side, tilt it to the right and the left, and then disengage it
from intake door lever (2). Pull up intake door lever knob
and remove it from intake door lever.
3.
Insert a remover tool (A) into the cutouts at the bottom of multi display unit (4), then pull straight back
to disengage pawls and metal clips.
4.
Pull back A/C finisher.
20. Remove A/C control fixing screws (with Manual A/C). Refer to
HAC-142, "Removal and Installation"
21. Remove cluster lid C.
1.
Remove fixing screws (A).
2.
Pull back cluster lid C, and disengage the pawls and metal
clips.
3.
Disconnect harness connector.
22. Remove audio unit or NAVI C/U.
• Audio unit: Refer to
AV-68, "Removal and Installation"
• NAVI C/U: Refer to
AV-139, "Removal and Installation"
.
23. Disconnect hazard switch harness connector.
24. Remove cluster tray.
1.
Insert a remover tool (A) between cluster tray and instru-
ment panel assembly, and then pull downward and disen-
gage metal clips.
2.
Pull back cluster tray.
3.
Disconnect harness connectors.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
JMJIA6910ZZ
: Pawl
: Metal clip
JMJIA4559ZZ
: Metal clip
JMJIA4560ZZ
Revision: 2013 October
2014 JUKE
IP-20
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
25. Release front pillar portion of front body side welt RH. Refer to
INT-21, "BODY SIDE WELT : Removal and
.
26. Remove front pillar garnish RH. Refer to
INT-18, "FRONT PILLAR GARNISH : Removal and Installation"
27. Remove instrument side finisher RH.
1.
Insert remover tool (A) between instrument side finisher RH
and instrument panel assembly to disengage the pawls as
shown in the figure.
2.
Pull back instrument side finisher RH.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
28. Remove glove box lid.
1.
Open glove box lid.
2.
Pull glove box lid (1) toward vehicle rear, and then disen-
gage the joint from instrument panel assembly (2).
3.
Disengage the pawl, and then remove damper pin on right
side.
CAUTION:
Never excessively pull string of glove box damper.
29. Remove glove box assembly.
1.
Remove fixing screws (A).
2.
Pull back the glove box cover assembly while holding the lower side and disengage the pawls.
3.
Disconnect glove box lamp harness connector.
: Pawl
JMJIA4561ZZ
JMJIA4563ZZ
: Pawl
JMJIA4564ZZ
: Pawl
JMJIA4565ZZ
Revision: 2013 October
2014 JUKE
INSTRUMENT PANEL ASSEMBLY
IP-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
30. Remove passenger air bag module. Refer to
SR-17, "Removal and Installation"
.
31. Remove switch panel.
1.
Insert remover tool (A) between switch panel and instru-
ment panel assembly to disengage the pawls as shown in
the figure.
2.
Pull up switch panel, and then disconnect harness connec-
tors.
CAUTION:
Apply protective tape (B) on the part to protect it from dam-
age.
32. Remove instrument panel assembly.
1.
Remove instrument panel assembly mounting screws (A) and bolts (B).
CAUTION:
Cover tool with a shop cloth to prevent windshield glass from being damaged.
2.
Disengage harness (A) and harness (B) of front pillar LH and RH portions from instrument panel
assembly.
3.
Remove instrument panel from passenger door opening portion.
CAUTION:
• Cover CVT shift selector upper surface with a shop cloth to prevent it from being damaged.
• When removing instrument panel assembly, 2 workers are required to prevent it from drop-
ping.
33. Remove the following parts after removing instrument panel assembly.
• Side defroster nozzle: Refer to
VTL-9, "SIDE DEFROSTER NOZZLE : Removal and Installation"
• Side defroster grille: Refer to
VTL-10, "SIDE DEFROSTER GRILLE : Removal and Installation"
.
• Side ventilator grille: Refer to
VTL-9, "SIDE VENTILATOR GRILLE : Removal and Installation"
.
• Front defroster nozzle: Refer to
VTL-10, "FRONT DEFROSTER NOZZLE : Removal and Installation"
.
• Center ventilator duct: Refer to
VTL-11, "CENTER VENTILATOR DUCT : Removal and Installation"
• Side ventilator duct: Refer to
VTL-11, "SIDE VENTILATOR DUCT : Removal and Installation"
.
: Pawl
JMJIA4566ZZ
JMJIA4567ZZ
JMJIA4568ZZ
Revision: 2013 October
2014 JUKE
IP-22
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
• GPS antenna: Refer to
AV-145, "Removal and Installation"
• Hazard switch: Refer to
EXL-105, "Removal and Installation"
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
• After installation, adjust the parking brake lever stroke. Refer to
PB-3, "Inspection and Adjustment"
• Never use the steering wheel mounting nut after removal, replace with the new nut.
• Never use the driver air bag module mounting bolts after removal, replace with the new bolts.
• Never use the passenger air bag module mounting bolts after removal, replace with the new bolts.
Revision: 2013 October
2014 JUKE
CENTER CONSOLE ASSEMBLY
IP-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
CENTER CONSOLE ASSEMBLY
Exploded View
INFOID:0000000009750204
CVT models
JSJIA0055ZZ
1.
Console indicator finisher
2.
Instrument lower cover RH
3.
Center console assembly
4.
Instrument lower cover LH
5.
Instrument stay
6.
CVT shift selector assembly
7.
Console rear bracket
8.
Console rear finisher
9.
Seat heated switch
10. Console switch finisher
11.
Console switch finisher
12. Console finisher assembly
13. Console mask
14. Console front bracket
: Pawl
: Metal clip
Revision: 2013 October
2014 JUKE
IP-24
< REMOVAL AND INSTALLATION >
CENTER CONSOLE ASSEMBLY
MT models
Removal and Installation
INFOID:0000000009750205
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.
REMOVAL
CAUTION:
When removing, always use a remover tool that is made of plastic.
JSJIA0056ZZ
1.
Console boot
2.
Instrument lower cover RH
3.
Center console assembly
4.
Instrument lower cover LH
5.
Instrument stay
6.
Console center bracket
7.
Console rear bracket
8.
Console rear finisher
9.
Seat heated switch
10. Console switch finisher
11.
Console switch finisher
12. Console finisher assembly
13. Console mask
14. Console front bracket
: Pawl
: Metal clip
Revision: 2013 October
2014 JUKE
CENTER CONSOLE ASSEMBLY
IP-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
1.
Remove shift lever knob (MT models only). Refer to
TM-21, "Removal and Installation"
2.
Remove console finisher assembly.
1.
Put selector lever in “N” position.
2.
Loosen the parking brake lever stroke by turning the adjusting nut with a socket wrench. Refer to
3, "Inspection and Adjustment"
.
3.
Lift up console finisher assembly in numerical order shown in the figure and disengage metal clips.
4.
Remove console finisher assembly while pulling it towards vehicle rear.
CAUTION:
• Be careful not for damaging parts in surrounding area.
• Remove metal clips slowly so that they are not damaged.
3.
Remove console rear finisher.
1.
Put front seat assembly (LH and RH) to frontmost position.
2.
Pull back console rear finisher, and disengage the pawls
and metal clips.
: Metal clip
JSJIA0057ZZ
: Pawl
: Metal clip
JMJIA4183ZZ
Revision: 2013 October
2014 JUKE
IP-26
< REMOVAL AND INSTALLATION >
CENTER CONSOLE ASSEMBLY
4.
Remove center console assembly fixing screws (A).
5.
Remove instrument lower cover LH.
1.
Put front seat assembly LH to rearmost position.
2.
Remove fixing clip (A).
3.
Pull the instrument lower cover LH crosswise, and disen-
gage the pawl and metal clips.
CAUTION:
Remove pawl and metal clips slowly so that they are not
damaged.
6.
Remove instrument lower cover RH.
1.
Put front seat assembly RH to rearmost position.
2.
Remove fixing clip (A).
3.
Pull the instrument lower cover RH crosswise, and disen-
gage the pawl and metal clips.
CAUTION:
Remove pawl and metal clips slowly so that they are not
damaged.
7.
Remove center console assembly.
1.
Remove center console fixing screws (A).
2.
Lift up center console assembly back side.
CAUTION:
Be careful not for damaging parts in surrounding area.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, adjust the parking brake lever stroke. Refer to
PB-3, "Inspection and Adjustment"
JMJIA4202ZZ
: Pawl
: Metal clip
JMJIA4551ZZ
: Pawl
: Metal clip
JMJIA4552ZZ
JMJIA4553ZZ
Revision: 2013 October
2014 JUKE
CENTER CONSOLE ASSEMBLY
IP-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Disassembly and Assembly
INFOID:0000000009750206
Disassembly and Assembly of Console Finisher Assembly
CAUTION:
When disassembling, always use a remover tool that is made of plastic.
DISASSEMBLY
1.
Remove console finisher assembly. Refer to
IP-24, "Removal and Installation"
.
2.
Remove console indicator finisher (CVT models)
Disengage connection of the console indicator finisher (2) fixing
pawls from the inside of the console finisher assembly (1)
toward the outside, and remove.
3.
Remove console indicator finisher (MT models)
Disengage connection of the console boot (2) fixing pawls from
the inside of the console finisher assembly (1) toward the out-
side, and remove.
4.
Remove console switch finisher.
Disengage connection of the console switch finisher (2) fixing
pawls from the inside of the console finisher assembly (1)
toward the outside, and remove.
NOTE:
Remove seat heated switch. Refer to
.
ASSEMBLY
Assemble in the reverse order of disassembly.
: Pawl
JMJIA4204ZZ
: Pawl
JMJIA4573ZZ
: Pawl
JMJIA4574ZZ
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст