Nissan Juke (2014 year). Service Repair Manual — part 19
BCS-102
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000009751652
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
DOOR LOCK
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)
INFOID:0000000010286784
WORK SUPPORT
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioning system
AIR CONDITONER
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
TPMS
AIR PRESSUE MONITOR
×
×
×
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-103
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: P range interlock door lock/unlock can be selected for M/T models, but automatic door lock/unlock function does not operate.
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function can be changed to operate with this mode
• On: Operate
• Off: Non-operation
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 24km/h (15MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other
than the P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to
OFF
• MODE 2*: All doors are unlocked when shifting the selector lever from any position other
than the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON
to OFF
• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position
other than the P to P position
• MODE 5: Driver side door is unlocked when key out of key switch
• MODE 6: All doors are unlocked when key out of key switch
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function can be selected from the following in this mode
• Off: Non-operation
• Unlock Only: Door unlock operation only
• Lock Only: Door lock operation only
• Lock/Unlock: Door lock and unlock operation
Monitor Item
Contents
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicated [On/Off] condition of key switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicated [On/Off] condition of back door switch
LOCK STATUS
Indicated [On/Off] condition of front door driver side
ACC ON SW
Indicated [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicated [On/Off] condition of lock signal from key fob
KEYLESS UNLOCK
Indicated [On/Off] condition of unlock signal from key fob
KEY CYL LK-SW
Indicated [On/Off] condition of lock signal from door key cylinder
KEY CYL UN-SW
Indicated [On/Off] condition of unlock signal from door key cylinder
VEHICLE SPEED
Display the vehicle speed signal received from combination meter by numer-
ical value [Km/h]
Revision: 2013 October
2014 JUKE
BCS-104
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
REAR WINDOW DEFOGGER
REAR WINDOW DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER)
INFOID:0000000010286826
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
BUZZER
BUZZER : CONSULT Function (BCM - BUZZER)
INFOID:0000000010286828
CONSULT APPLICATION ITEMS
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LCK” on CONSULT screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT screen is
touched
• The back door lock actuator is unlocked when “BD ULK” on CONSULT screen is touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT screen is
touched
Monitor Item
Description
REAR DEF SW
Displays “Press (ON)/other (OFF)” status determined with the rear window defogger switch.
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch ACC position.
Test Item
Description
REAR DEFOGGER
Rear window defogger operates when “ON” on CONSULT screen is touched.
Test item
Diagnosis mode
Description
BUZZER
Data Monitor
Displays BCM input data in real time.
Active Test
Operation of electrical loads can be checked by sending driving signal to them.
Display item
[Unit]
Description
IGN ON SW
[On/Off]
Status of ignition switch judged by BCM.
KEY ON SW
[On/Off]
Status of key switch judged by BCM.
DOOR SW-DR
[km/h]
Status of driver side door switch judged by BCM.
REVERSE SW CAN
[On/Off]
This item is displayed, but cannot be monitored.
TAIL LAMP SW
[On/Off]
Status of lighting switch judged by BCM using the combination switch readout function.
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-105
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
INT LAMP
INT LAMP : CONSULT Function (BCM - INT LAMP)
INFOID:0000000010286821
WORK SUPPORT
FR FOG SW
[On/Off]
Status of front fog lamp switch judged by BCM using the combination switch readout function.
BUCKLE SW
[On/Off]
Status of seat belt buckle switch (driver side) received from combination meter with CAN communica-
tion line.
VEHICLE SPEED
[km/h]
Value of vehicle speed signal received from combination meter with CAN communication line.
Display item
[Unit]
Description
Display item
[Unit]
Description
SEAT BELT WARN TEST
The seat belt warning chime operation can be checked by operating the relevant function (On/Off).
IGN KEY WARN ALM
The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM
The light warning chime operation can be checked by operating the relevant function (On/Off).
JPLIA0093GB
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 1
0 sec.
Sets the interior room lamp ON time. (Timer operating time)
MODE 2
7.5 sec.
MODE 3*
15 sec.
MODE 4
30 sec.
SET I/L D-UNLCK INTCON
On*
With the interior room lamp timer function
Off
Without the interior room lamp timer function
ROOM LAMP ON TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual brightening time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
4 sec.
MODE 6
5 sec.
MODE 7
0 sec.
Revision: 2013 October
2014 JUKE
BCS-106
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
ROOM LAMP OFF TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual dimming time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
4 sec.
MODE 6
5 sec.
MODE 7
0 sec.
R LAMP TIMER LOGIC SET
MODE 1*
Interior room lamp timer activates with synchronizing all doors.
MODE 2
Interior room lamp timer activates with synchronizing the driver door
only.
Service item
Setting item
Setting
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Indicated [On/Off] condition of ignition switch in ON position
KEY ON SW
[On/Off]
Indicated [On/Off] condition of key switch
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW- RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
BACK DOOR SW
[On/Off]
Indicated [On/Off] condition of back door switch
LOCK STATUS
[On/Off]
The switch status input from door lock status switch (driver side)
CDL LOCK SW
[On/Off]
Indicates [On/Off] condition of door lock and unlock switch
CDL UNLOCK SW
[On/Off]
Indicates [On/Off] condition of door lock and unlock switch
KEYLESS LOCK
[On/Off]
Indicates [On/Off] condition of lock signal from keyfob
KEYLESS UNLOCK
[On/Off]
Indicates [On/Off] condition of unlock signal from keyfob
TRNK/HAT MNTR
[On/Off]
NOTE:
This item is displayed, but cannot be tested
KEY CYL LK-SW
[On/Off]
Indicated [On/Off] condition of lock signal from door key cylinder
KEY CYL UN-SW
[On/Off]
Indicated [On/Off] condition of unlock signal from door key cylinder
ACC ON SW
[On/Off]
Indicates [On/Off] condition of ignition switch in ACC position
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-107
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
MULTI REMOTE ENT
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT)
INFOID:0000000010286785
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
WORK SUPPORT
Test item
Operation
Description
INT LAMP
On
Outputs the interior room lamp control signal.
Off
Stops the interior room lamp control signal.
Monitor Item
Condition
IGN ON SW
Indicates [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicates [On/Off] condition of key switch
ACC ON SW
Indicates [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicates [On/Off] condition of lock signal from keyfob
KEYLESS UNLOCK
Indicates [On/Off] condition of unlock signal from keyfob
KYLS TRNK/HAT
NOTE:
This item is displayed, but cannot be tested
DOOR SW-DR
Indicates [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicates [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicates [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicates [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicates [On/Off] condition of back door switch
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be tested
CDL LOCK SW
Indicates [On/Off] condition of door lock and unlock switch
CDL UNLOCK SW
Indicates [On/Off] condition of door lock and unlock switch
KEYLESS PANIC
Indicates [On/Off] condition of PANIC button of keyfob
Test item
Description
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
This test is able to check horn operation
• On: Operate
Test item
Description
REMO CONT IN REGIST
Keyfob ID code can be registered
REMO CONT IN ERASUR
Keyfob ID code can be erased
REMO CONT IN CONFIR
It can be checked whether Intelligent Key ID code is registered or not in this mode
HORN CHIRP SET
Hazard and horn reminder function (horn operation) mode can be changed in this mode
• On: Operate
• Off: Non-operation
Revision: 2013 October
2014 JUKE
BCS-108
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP)
INFOID:0000000010286817
WORK SUPPORT
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
HAZARD LAMP SET
Hazard and horn reminder function (hazard operation) mode can be changed in this mode
• MODE1: Non-operation
• MODE2: Unlock operation only
• MODE3: Lock operation only
• MODE4: Lock and unlock operation
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
PANIC ALARM SET
Panic alarm button pressing time on keyfob remote control button can be selected from the
following with this mode
• MODE1: 0.5 sec
• MODE2: Non-operation
• MODE3: 1.5 sec
TRUNK OPEN SET
NOTE:
This item is displayed, but cannot be tested
Test item
Description
Service item
Setting item
Setting
BATTERY SAVER SET
On*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET
MODE 1
NOTE:
This item is displayed but is not operated
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
MODE 7
MODE 8
HEAD LIGHT TIMER
MODE 1
10 sec.
Sets follow me home function activating time
MODE 2
*
30 sec.
AUTO LIGHT LOGIC SET
MODE 1
NOTE:
This item is displayed but is not operated
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-109
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: For models without front fog lamp, this item is displayed but is not monitored.
ACTIVE TEST
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Indicated [On/Off] condition of ignition switch in ON position
ACC ON SW
[On/Off]
Indicates [On/Off] condition of ignition switch in ACC position
VEHICLE SPEED
[km/h]
Display the vehicle speed signal received from combination meter by numerical value
[Km/h]
HI BEAM SW
[On/Off]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
FR FOG SW*
[On/Off]
AUTO LIGHT SW
[On/Off]
NOTE:
This item is indicated, but can not monitored
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
BACK DOOR SW
[On/Off]
The switch status input from back door switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
KEY ON SW
[On/Off]
Indicated [On/Off] condition of key switch
KEYLESS LOCK
[On/Off]
Indicated [On/Off] condition of lock signal from key fob
PKB SW
[On/Off]
The parking brake switch status received from combination meter with CAN commu-
nication
ENGINE RUN
[On/Off]
The engine status received from ECM with CAN communication
OPTI SEN (DTCT)
[V]
NOTE:
This item is indicated, but can not monitored
OPTI SEN (FILT)
[V]
NOTE:
This item is indicated, but can not monitored
LIG SEN COND
[On/Off/NG]
NOTE:
This item is indicated, but can not monitored
Revision: 2013 October
2014 JUKE
BCS-110
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*
1
: For models without front fog lamp, this item is displayed but is not tested.
*
2
: For models without daytime running light system, this item is not displayed.
WIPER
WIPER : CONSULT Function (BCM - WIPER)
INFOID:0000000010286824
WORK SUPPORT
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON
Off
Stops the tail lamp request signal transmission
HEAD LAMP
Hi
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI)
Lo
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO)
Off
Stops the high & low beam request signal transmission
FR FOG LAMP*
1
On
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON
Off
Stops the front fog lights request signal transmission
DAYTIME RUNNING LIGHT*
2
On
Transmits the daytime running light request signal via CAN communica-
tion to IPDM E/R
Off
Stop the daytime running light request signal transmission
ILL DIM SIGNAL
On
NOTE:
This item is indicated, but can not tested
Off
Service item
Setting item
Description
WIPER SPEED
SETTING
On
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
Off*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Monitor Item
[Unit]
Description
IGN ON SW
[On/Off]
Ignition switch ON status judged from ignition power supply.
IGN SW CAN
[On/Off]
Ignition switch ON status received from IPDM E/R with CAN communication.
FR WIPER HI
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER LOW
[On/Off]
FR WIPER INT
[On/Off]
FR WASHER SW
[On/Off]
INT VOLUME
[1
−
7]
Each switch status that BCM judges from the combination switch reading function.
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-111
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER)
INFOID:0000000010286818
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
FR WIPER STOP
[On/Off]
Front wiper motor (stop position) status received from IPDM E/R with CAN communication.
VEHICLE SPEED
[km/h]
The value of the vehicle speed signal received from combination meter with CAN communication.
RR WIPER ON
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
RR WIPER INT
[On/Off]
RR WASHER SW
[On/Off]
RR WIPER STOP
[On/Off]
Rear wiper motor (stop position) status input from the rear wiper motor.
REVERSE SW CAN
[On/Off]
Reverse position status as judged from TCM with CAN communication.
RAIN SENSOR
[Off/LOW/HIGH/SPLASH/NG]
NOTE:
This item is displayed, but cannot be monitored.
Monitor Item
[Unit]
Description
Test item
Operation
Description
FR WIPER
Hi
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to
operate the front wiper HI operation.
Lo
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
Off
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
On
Outputs the voltage to operate the rear wiper motor.
Off
Stops the voltage to stop.
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Indicates [On/Off] condition of ignition switch in ON position
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
Revision: 2013 October
2014 JUKE
BCS-112
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
AIR CONDITIONER
AIR CONDITIONER : CONSULT Function (BCM - AIR CONDITIONER) (Manual A/C)
INFOID:0000000010286780
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Display item list
ACTIVE TEST
COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)
INFOID:0000000009751662
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test item
Operation
Description
FLASHER
RH
Outputs the voltage to turn the right side turn signal lamps ON.
LH
Outputs the voltage to turn the left side turn signal lamps ON.
Off
Stops the voltage to turn the turn signal lamps OFF.
Monitor Item [Unit]
Contents
FAN ON SIG
[On/Off]
Displays blower motor status as judged from blower fan ON signal.
AIR COND SW
[On/Off]
Displays A/C switch status as judged from A/C switch signal.
THERMO AMP
[On/Off]
Displays thermo control amp. status as judged from thermo control amp. signal.
IGN SW
[On/Off]
Displays ignition switch position status as judged form ignition switch signal.
FR DEF SW
[On/Off]
Displays the D/F or DEF status as judged from defroster position signal.
Test item
Operation
Description
A/C INDICATOR
On
A/C indicator is turned ON.
Off
A/C indicator is turned OFF.
Monitor item [UNIT]
Description
TURN SIGNAL R
[Off/On]
Displays the status of TURN RH switch in combination switch judged by the combination switch reading func-
tion.
TURN SIGNAL L
[Off/On]
Displays the status of the TURN LH switch in combination switch judged by the combination switch reading
function.
HI BEAM SW
[Off/On]
Displays the status of HI BEAM switch in combination switch judged by the combination switch reading func-
tion.
HEAD LAMP SW 1
[Off/On]
Displays the status of HEADLAMP 1 switch in combination switch judged by the combination switch reading
function.
HEAD LAMP SW 2
[Off/On]
Displays the status of HEADLAMP 2 switch in combination switch judged by the combination switch reading
function.
TAIL LAMP SW
[Off/On]
Displays the status of TAIL LAMP switch in combination switch judged by the combination switch reading
function.
PASSING SW
[Off/On]
Displays the status of PASSING switch in combination switch judged by the combination switch reading func-
tion.
AUTO LIGHT SW
[Off/On]
NOTE:
This item is indicated, but not monitored.
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-113
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BCM
BCM : CONSULT Function (BCM - BCM)
INFOID:0000000009751663
WORK SUPPORT
IMMU
IMMU : CONSULT Function (BCM - IMMU)
INFOID:0000000010286808
WORK SUPPORT
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)
INFOID:0000000010286822
WORK SUPPORT
FR FOG SW
[Off/On]
Displays the status of FR FOG switch in combination switch judged by the combination switch reading func-
tion.
RR FOG SW
[Off/On]
NOTE:
This item is indicated, but not monitored.
FR WIPER HI
[Off/On]
Displays the status of FR WIPER HI switch in combination switch judged by the combination switch reading
function.
FR WIPER LOW
[Off/On]
Displays the status of FR WIPER LOW switch in combination switch judged by the combination switch read-
ing function.
FR WIPER INT
[Off/On]
Displays the status of FR WIPER INT switch in combination switch judged by the combination switch reading
function.
FR WASHER SW
[Off/On]
Displays the status of FR WASHER switch in combination switch judged by the combination switch reading
function.
INT VOLUME
[1 - 7]
Displays the status of wiper intermittent dial position judged by the combination switch reading function.
RR WIPER ON
[Off/On]
Displays the status of RR WIPER switch in combination switch judged by the combination switch reading
function.
RR WIPER INT
[Off/On]
Displays the status of RR WIPER INT switch in combination switch judged by the combination switch reading
function.
RR WASHER SW
[Off/On]
Displays the status of RR WASHER switch in combination switch judged by the combination switch reading
function.
Monitor item [UNIT]
Description
Item
Description
RESET SETTING VALUE
Return a value set with WORK SUPPORT of each system to a default value in factory shipment.
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation. Security indicator lamp will be
turned on when “ON” on CONSULT screen is touched.
Revision: 2013 October
2014 JUKE
BCS-114
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*:Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
TRUNK
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 1
30 min.
Sets the interior room lamp battery saver timer operating
time.
NOTE:
The factor setting is 10 minutes. The setting cannot be re-
turned to the factory setting, when the setting is changed
once.
MODE 2
60 min.
MODE 3
15 min.
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Indicated [On/Off] condition of ignition switch in ON position
KEY ON SW
[On/Off]
Indicated [On/Off] condition of key switch
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW- RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
BACK DOOR SW
[On/Off]
Indicated [On/Off] condition of back door switch
LOCK STATUS
[On/Off]
The switch status input from door lock status switch (driver side)
CDL LOCK SW
[On/Off]
Indicates [On/Off] condition of door lock and unlock switch
CDL UNLOCK SW
[On/Off]
Indicates [On/Off] condition of door lock and unlock switch
KEYLESS LOCK
[On/Off]
Indicates [On/Off] condition of lock signal from keyfob
KEYLESS UNLOCK
[On/Off]
Indicates [On/Off] condition of unlock signal from keyfob
TRNK/HAT MNTR
[On/Off]
NOTE:
This item is displayed, but cannot be tested
KEY CYL LK-SW
[On/Off]
Indicated [On/Off] condition of lock signal from door key cylinder
KEY CYL UN-SW
[On/Off]
Indicated [On/Off] condition of unlock signal from door key cylinder
ACC ON SW
[On/Off]
Indicates [On/Off] condition of ignition switch in ACC position
Test item
Operation
Description
BATTERY SAVER
Off
Cuts the interior room lamp power supply.
On
Outputs the interior room lamp power supply.
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-115
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
TRUNK : CONSULT Function (BCM - TRUNK)
INFOID:0000000010286786
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
THEFT ALM
THEFT ALM : CONSULT Function (BCM - THEFT)
INFOID:0000000010286807
WORK SUPPORT
ACTIVE TEST
RETAIND PWR
RETAIND PWR : CONSULT Function (BCM - RETAINED PWR)
INFOID:0000000010286811
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
SIGNAL BUFFER
Monitor Item
Contents
KEY ON SW
Indicates [On/Off] condition of key switch.
LOCK STATUS
NOTE:
This item is displayed, but cannot be monitored.
VEHICLE SPEED
Indicates [Km/h] condition of vehicle speed signal from combination meter.
IGN ON SW
Indicates [On/Off] condition of ignition switch.
TRNK OPNR SW
NOTE:
This item is displayed, but cannot be monitored.
KYLS TRNK/HAT
NOTE:
This item is displayed, but cannot be monitored.
Service Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation. Security indicator lamp will be
turned on when “ON” on CONSULT screen is touched.
VEHICLE SECURITY HORN
This test is able to check horn operation. Horn will be activated for 0.5 seconds after “ON” on
CONSULT screen is touched.
HEADLAMP (HI)
This test is able to check headlamp (HI) operation. Headlamps (HI) will be activated for 0.5
seconds after “ON” on CONSULT screen is touched.
FLASHER
This test is able to check hazard warning lamp operation. Hazard warning lamps will be acti-
vated after “LH” or “RH” on CONSULT screen is touched.
Monitor Item
Description
DOOR SW-DR
Indicates [ON/OFF] condition of driver side door switch.
DOOR SW-AS
Indicates [ON/OFF] condition of passenger side door switch.
Revision: 2013 October
2014 JUKE
BCS-116
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER)
INFOID:0000000009751669
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
PANIC ALARM
PANIC ALARM : CONSULT Function (BCM - PANIC ALARM)
INFOID:0000000010286809
ACTIVE TEST
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
TOR)
INFOID:0000000010286830
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SELF DIAGNOSTIC RESULT
DATA MONITOR MODE
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor item [UNIT]
Description
OIL PRESS SW
[Off/On]
NOTE:
This item is indicated, but not monitored.
BRAKE SW
[Off/On]
Displays the switch status input from stop lamp switch.
Test item
Operation
Description
OIL PRESSURE SW
Off
NOTE:
This item is indicated, but not tested.
On
Test item
Description
VEHICLE SECURITY HORN
This test is able to check horn operation.
Horn is activated for 0.5 seconds after “ON” on CONSULT screen touched.
HEAD LAMP (HI)
This test is able to check headlamp (HI) operation.
Headlamps (HI) will be activated after “ON” on CONSULT screen touched.
Diagnosis mode
Function Description
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Work Support
Components can be quickly and accurately adjusted.
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-117
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST MODE
NOTE:
After completing the work below, perform an active test.
1.
Check ID registration state and perform self-diagnosis.
2.
Erase the self-diagnosis result history.
WORK SUPPORT
Monitor item (Unit)
Remarks
AIR PRESS FL
(kPa, kg/cm2 or Psi)
Tire pressure
AIR PRESS FR
(kPa, kg/cm2 or Psi)
AIR PRESS RR
(kPa, kg/cm2 or Psi)
AIR PRESS RL
(kPa, kg/cm2 or Psi)
ID REGST FL1
(Yet, Done)
Registration ID
ID REGST FR1
(Yet, Done)
ID REGST RR1
(Yet, Done)
ID REGST RL1
(Yet, Done)
WARNING LAMP
(On/Off)
Low tire pressure warning lamp
BUZZER
(On/Off)
NOTE:
This item is displayed, but cannot be use this item.
Item
Description
WARNING LAMP
Low tire pressure warning lamp can be turned ON arbitrarily.
ID REGIST WARNING
NOTE:
Displayed but not used in TPMS.
RUN FLAT TIRE W/L
NOTE:
Displayed but not used in TPMS.
FLASHER
Turn signal lamps can be turned ON arbitrarily.
RUN FLAT TIRE W/R
NOTE:
Displayed but not used in TPMS.
Item
Description
ID READ
Registered tire pressure sensor ID can be displayed.
ID REGIST
Tire pressure sensor ID can be registered.
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст