Nissan Juke (2014 year). Service Repair Manual — part 234
B1215, B1216, B1217 SATELLITE SENSOR LH
SRC-151
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
SRC-152
< DTC/CIRCUIT DIAGNOSIS >
B1218, B1219, B1220, B1221, B1222, B1223 DIAGNOSIS SENSOR UNIT
B1218, B1219, B1220, B1221, B1222, B1223 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000009751860
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-152, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751861
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1218
B1219
B1220
B1221
B1222
B1223
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
B1234, B1235, B1236, B1237, B1238, B1239 DIAGNOSIS SENSOR UNIT
SRC-153
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1234, B1235, B1236, B1237, B1238, B1239 DIAGNOSIS SENSOR UNIT
DTC Logic
INFOID:0000000009751862
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-153, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751863
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1234
B1235
B1236
B1237
B1238
B1239
CONTROL UNIT
Air bag diagnosis sensor unit is malfunctioning
Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
SRC-154
< DTC/CIRCUIT DIAGNOSIS >
B1336, B1337 SATELLITE SENSOR RH
B1336, B1337 SATELLITE SENSOR RH
DTC Logic
INFOID:0000000009751864
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-154, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751865
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor RH. Refer to
SR-25, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of CON-
SULT
DTC detecting condition
Possible cause
B1336
B1337
FR-RH DOOR SATEL
SENS
[SENSOR MALFUNC-
TION]
Front door satellite sensor RH is malfunc-
tioning
• Harness or connectors
• Malfunction in front door satellite sensor RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
B1336, B1337 SATELLITE SENSOR RH
SRC-155
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
SRC-156
< DTC/CIRCUIT DIAGNOSIS >
B1338, B1340, B1341, B1342 SATELLITE SENSOR RH
B1338, B1340, B1341, B1342 SATELLITE SENSOR RH
DTC Logic
INFOID:0000000009751866
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-156, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751867
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor RH. Refer to
SR-25, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1338
B1340
B1341
B1342
FR-RH DOOR SATEL
SENS
[COMM MALFUNC-
TION]
Front door satellite sensor RH is malfunc-
tioning
• Harness or connectors
• Malfunction in front door satellite sensor RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
B1338, B1340, B1341, B1342 SATELLITE SENSOR RH
SRC-157
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
SRC-158
< DTC/CIRCUIT DIAGNOSIS >
B1339 SATELLITE SENSOR RH
B1339 SATELLITE SENSOR RH
DTC Logic
INFOID:0000000009751868
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-158, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751869
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor RH. Refer to
SR-25, "Removal and Installation"
.
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1339
FR-RH DOOR SATEL
SENS
[MIS-INSTALLATION]
Front door satellite sensor RH is out of the
specified specification
Diagnosis sensor unit or front door satellite sen-
sor RH is different from the part specified
Revision: 2013 October
2014 JUKE
B1343, B1344 SATELLITE SENSOR LH
SRC-159
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1343, B1344 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000009751870
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-159, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751871
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor LH. Refer to
SR-25, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1343
B1344
FR-LH DOOR SATEL
SENS
[SENSOR MALFUNC-
TION]
Front door satellite sensor LH is malfunc-
tioning
• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
SRC-160
< DTC/CIRCUIT DIAGNOSIS >
B1343, B1344 SATELLITE SENSOR LH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
B1345, B1347, B1348, B1349 SATELLITE SENSOR LH
SRC-161
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1345, B1347, B1348, B1349 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000009751872
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-164, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751873
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
REPLACE SATELLITE SENSOR
1.
Replace front door satellite sensor LH. Refer to
SR-25, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1345
B1347
B1348
B1349
FR-LH DOOR SATEL
SENS
[COMM MALFUNC-
TION]
Front door satellite sensor LH is malfunc-
tioning
• Harness or connectors
• Malfunction in front door satellite sensor LH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
SRC-162
< DTC/CIRCUIT DIAGNOSIS >
B1345, B1347, B1348, B1349 SATELLITE SENSOR LH
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: 2013 October
2014 JUKE
B1346 SATELLITE SENSOR LH
SRC-163
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1346 SATELLITE SENSOR LH
DTC Logic
INFOID:0000000009751874
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-163, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751875
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
REPLACE FRONT DOOR SATELLITE SENSOR
1.
Replace front door satellite sensor LH. Refer to
SR-25, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1346
FR-LH DOOR SATEL
SENS
[MIS-INSTALLATION]
Front door satellite sensor LH is out of the
specified specification
Diagnosis sensor unit or front door satellite sen-
sor LH is different from the part specified
Revision: 2013 October
2014 JUKE
SRC-164
< DTC/CIRCUIT DIAGNOSIS >
B1350, B1351 SATELLITE SENSOR
B1350, B1351 SATELLITE SENSOR
DTC Logic
INFOID:0000000009751876
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1.
Turn ignition switch ON.
2.
Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1.
Turn ignition switch ON.
2.
Check the air bag warning lamp status. Refer to
SRC-12, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
SRC-164, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009751877
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
REPLACE BOTH OF FRONT DOOR SATELLITE SENSOR
1.
Replace both of front door satellite sensor. Refer to
SR-25, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Perform DTC confirmation procedure. Refer to
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
DTC
Display contents of
CONSULT
DTC detecting condition
Possible cause
B1350
B1351
FR DOOR SATEL SENS
Front door satellite sensor is malfunction-
ing or out of the specified specification
• Malfunction in front door satellite sensor LH/RH
• Malfunction in air bag diagnosis sensor unit
Revision: 2013 October
2014 JUKE
SRS AIR BAG WARNING LAMP DOES NOT TURN OFF
SRC-165
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
SYMPTOM DIAGNOSIS
SRS AIR BAG WARNING LAMP DOES NOT TURN OFF
Diagnosis Procedure
INFOID:0000000009751878
1.
CHECK AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Check the deployment of air bag module and seat belt pre-tensioner.
Is air bag module deployed?
YES
>> Replace the malfunctioning parts.
NO
>> GO TO 2.
2.
CHECK AIR BAG FUSE
Check 10 A fuse [No.2, located in fuse block (J/B)].
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the fuse.
3.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace harness connectors.
4.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace wiring harness.
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1.
Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
2.
Check air bag warning lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 6.
6.
REPLACE COMBINATION METER
1.
Replace combination meter. Refer to
MWI-61, "Removal and Installation"
2.
Check air bag warning lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 1.
Revision: 2013 October
2014 JUKE
SRC-166
< SYMPTOM DIAGNOSIS >
SRS AIR BAG WARNING LAMP DOES NOT TURN ON
SRS AIR BAG WARNING LAMP DOES NOT TURN ON
Diagnosis Procedure
INFOID:0000000009751879
1.
CHECK COMBINATION METER POWER SUPPLY AND GROUND CIRCUIT
Check combination meter unit power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace harness connectors.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace wiring harness.
4.
CHECK AIR BAG DIAGNOSIS SENSOR UNIT
Disconnect air bag diagnosis sensor unit connector and turn ignition switch ON.
Does air bag warning lamp turn ON?
YES
>> Replace air bag diagnosis sensor unit. Refer to
SR-28, "Removal and Installation"
.
NO
>> Replace combination meter. Refer to
MWI-61, "Removal and Installation"
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст