Nissan Juke (2014 year). Service Repair Manual — part 198
SYSTEM INITIALIZATION
PWC-27
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
SYSTEM INITIALIZATION
Description
INFOID:0000000009753791
If any of the following operations are performed, the initialization is necessary for normal operation of power
window system.
• Disconnection and connection of battery cable from negative terminal.
• When power window main switch replaced.
• Electric power supply to power window main switch or power window motor (driver side) is interrupted by
blown fuse or disconnection and connection of the negative terminal of battery, etc.
• Disconnection and connection of power window main switch harness connector.
• Removal of power window motor (driver side) from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
CAUTION:
The following specified operations can not be performed under the non-initialized condition.
• Auto-up operation
• Anti-pinch function
Work Procedure
INFOID:0000000009753792
1.
STEP 1
1.
Turn ignition switch ON.
2.
Operate power window switch to fully open the window. (This operation is unnecessary if the window is
already fully open)
3.
Continue pulling the power window switch UP (AUTO-UP operation). Even after glass stops at fully closed
position, keep pulling the switch for 2 seconds or more.
4.
Check that AUTO-UP function operates normally.
>> GO TO 2.
2.
STEP 2
Check anti-pinch function. Refer to
>> END
Revision: 2013 October
2014 JUKE
PWC-28
< BASIC INSPECTION >
CHECK ANTI-PINCH FUNCTION
CHECK ANTI-PINCH FUNCTION
Description
INFOID:0000000009753793
If any of the following operations are performed, the initialization is necessary for normal operation of anti-
pinch function.
• Disconnection and connection of battery cable from negative terminal.
• When power window main switch replaced.
• Electric power supply to power window main switch or power window motor (driver side) is interrupted by
blown fuse or disconnection and connection of the negative terminal of battery, etc.
• Disconnection and connection of power window main switch harness connector.
• Removal of power window motor (driver side) from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of glass.
• Removal and installation of door glass run.
Work Procedure
INFOID:0000000009753794
1.
CHECK ANTI-PINCH FUNCTION
1.
Fully open the door window.
2.
Place a piece of wood near fully closed position.
3.
Close door glass completely with AUTO-UP.
4.
Check the following conditions.
-
Check that glass lowers for approximately 150 mm (5.9 in) without pinching piece of wood and stops.
-
Check that glass does not rise not when operating the power window main switch while lowering.
CAUTION:
•
Perform initial setting when AUTO-UP operation or anti-pinch function does not operate nor-
mally.
•
Check that AUTO-UP operates before inspection when system initialization is performed.
•
Do not check with hands and other body parts because they may be pinched. Do not get
pinched.
>> END
Revision: 2013 October
2014 JUKE
POWER SUPPLY AND GROUND CIRCUIT
PWC-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
POWER WINDOW MAIN SWITCH
POWER WINDOW MAIN SWITCH : Diagnosis Procedure
INFOID:0000000009753795
1.
CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check voltage between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK POWER WINDOW MAIN SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and power window main switch harness connector.
4.
Check continuity between BCM harness connector and ground.
(): Without Intelligent Key
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
NO
>> Repair or replace harness.
3.
CHECK POWER WINDOW MAIN SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace harness.
(+)
(-)
Condition
Voltage (V)
Power window main switch
Connector
Terminal
D35
10
Ground
Ignition switch
ON
9 – 16
D36
18
OFF
BCM
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
M69 (M66)
68 (67)
D35
10
Existed
69 (66)
D36
18
BCM
Ground
Continuity
Connector
Terminal
M69 (M66)
68 (67)
Not existed
69 (66)
Power window main switch
Ground
Continuity
Connector
Terminal
D35
1
Existed
Revision: 2013 October
2014 JUKE
PWC-30
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
FRONT POWER WINDOW SWITCH (PASSENGER SIDE) : Diagnosis Procedure
INFOID:0000000009753796
1.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect front power window switch (passenger side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and front power window switch (passenger side) har-
ness connector.
4.
Check continuity between BCM harness connector and ground.
(): Without Intelligent Key
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
(without Intelligent Key).
NO
>> Repair or replace harness.
REAR POWER WINDOW SWITCH
REAR POWER WINDOW SWITCH : Diagnosis Procedure
INFOID:0000000009753797
1.
CHECK REAR POWER WINDOW SWITCH POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect rear power window switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between rear power window switch harness connector and ground.
(+)
(-)
Voltage (V)
Front power window switch (passenger side)
Connector
Terminal
D10
1
Ground
9 – 16
BCM
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M69 (M66)
68 (67)
D10
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M69 (M66)
68 (67)
Not existed
(+)
(-)
Voltage (V)
Rear power window switch
Connector
Terminal
LH
D63
1
Ground
9 – 16
RH
D43
Revision: 2013 October
2014 JUKE
POWER SUPPLY AND GROUND CIRCUIT
PWC-31
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK REAR POWER WINDOW SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and rear power window switch harness connector.
4.
Check continuity between BCM harness connector and ground.
(): Without Intelligent Key
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
NO
>> Repair or replace harness.
BCM
Rear power window switch
Continuity
Connector
Terminal
Connector
Terminal
M69 (M66)
68 (67)
LH
D63
1
Existed
RH
D43
BCM
Ground
Continuity
Connector
Terminal
M69 (M66)
68 (67)
Not existed
Revision: 2013 October
2014 JUKE
PWC-32
< DTC/CIRCUIT DIAGNOSIS >
FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Component Function Check
INFOID:0000000009753798
1.
CHECK FUNCTION
Check front power window motor (passenger side) operation with front power window switch (passenger side).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009753799
1.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front power window switch (passenger side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check continuity between front power window switch (passenger side) harness connector and power win-
dow main switch harness connector.
4.
Check continuity between front power window switch (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-55, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
Check front power window switch (passenger side).
Refer to
PWC-33, "Component Inspection"
Is the inspection result normal?
(+)
(-)
Condition
Voltage (V)
Front power window switch (passenger side)
Connector
Terminal
D10
2
Ground
Power window main
switch
(passenger side)
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
Front power window switch (passenger side)
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
D10
2
D35
16
Existed
3
2
Front power window switch (passenger side)
Ground
Continuity
Connector
Terminal
D10
2
Not existed
3
Revision: 2013 October
2014 JUKE
FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
PWC-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
YES
>> GO TO 4.
NO
>> Replace front power window switch (passenger side).
4.
CHECK INTERMITTENT INCIDENT
GI-46, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000009753800
1.
CHECK FRONT POWER WINDOW SWITCH (PASSENGER SIDE)
1.
Turn ignition switch OFF.
2.
Disconnect front power window switch (passenger side) connector.
3.
Check front power window switch (passenger side) terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front power window switch (passenger side).
Front power window switch (passenger side)
Condition
Continuity
Terminal
1
5
UP
Existed
3
4
2
5
NEUTRAL
3
4
1
4
DOWN
2
5
Revision: 2013 October
2014 JUKE
PWC-34
< DTC/CIRCUIT DIAGNOSIS >
REAR POWER WINDOW SWITCH
REAR POWER WINDOW SWITCH
Component Function Check
INFOID:0000000009753801
1.
CHECK FUNCTION
Check rear power window motor operation with rear power window switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009753802
1.
CHECK REAR POWER WINDOW SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear power window switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between rear power window switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK REAR POWER WINDOW SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check continuity between rear power window switch harness connector and power window main switch
harness connector.
4.
Check continuity between rear power window switch harness connector and ground.
(+)
(-)
Condition
Voltage (V)
Rear power window switch
Connector
Terminal
LH
D63
2
Ground
Power window main
switch
(rear LH side)
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
RH
D43
2
Power window main
switch
(rear RH side)
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
Rear power window switch
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
LH
D63
2
D35
9
Existed
3
8
RH
D43
2
7
3
6
Revision: 2013 October
2014 JUKE
REAR POWER WINDOW SWITCH
PWC-35
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-55, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK REAR POWER WINDOW SWITCH
Check rear power window switch.
Refer to
PWC-35, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace rear power window switch.
4.
CHECK INTERMITTENT INCIDENT
GI-46, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000009753803
1.
CHECK REAR POWER WINDOW SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect rear power window switch connector.
3.
Check rear power window switch terminals under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace rear power window switch.
Rear power window switch
Ground
Continuity
Connector
Terminal
LH
D63
2
Not existed
3
RH
D43
2
3
Rear power window switch
Condition
Continuity
Terminal
1
5
UP
Existed
3
4
2
5
NEUTRAL
3
4
1
4
DOWN
2
5
Revision: 2013 October
2014 JUKE
PWC-36
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW MOTOR
POWER WINDOW MOTOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000009753804
1.
CHECK FUNCTION
Check front power window motor (driver side) operation with power window main switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-36, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000009753805
1.
CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front power window motor (driver side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (driver side).
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check continuity between front power window motor (driver side) harness connector and power window
main switch harness connector.
4.
Check continuity between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-55, "Removal and Installation"
NO
>> Repair or replace harness.
PASSENGER SIDE
(+)
(-)
Condition
Voltage (V)
Front power window motor (driver side)
Connector
Terminal
D37
2
Ground
Power window main
switch
(driver side)
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
Front power window motor (driver side)
Power window main switch
Continuity
Connector
Terminal
Connector
Terminal
D37
2
D35
17
Existed
3
19
Front power window motor (driver side)
Ground
Continuity
Connector
Terminal
D37
2
Not existed
3
Revision: 2013 October
2014 JUKE
POWER WINDOW MOTOR
PWC-37
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
PASSENGER SIDE : Component Function Check
INFOID:0000000009753806
1.
CHECK FUNCTION
Check front power window motor (passenger side) operation with power window main switch or front power
window switch (passenger side).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-37, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000009753807
1.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front power window motor (passenger side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between front power window motor (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (passenger side).
NO
>> GO TO 2.
2.
CHECK FRONT POWER WINDOW MOTOR (PASSENGER SIDE) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect front power window switch (passenger side) connector.
3.
Check continuity between front power window motor (passenger side) harness connector and front power
window switch (passenger side) harness connector.
4.
Check continuity between front power window motor (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window switch (passenger side).
NO
>> Repair or replace harness.
REAR LH
REAR LH : Component Function Check
INFOID:0000000009753808
1.
CHECK FUNCTION
(+)
(-)
Condition
Voltage (V)
Front power window motor (passenger side)
Connector
Terminal
D16
1
Ground
Front power window
switch
(passenger side)
NEUTRAL
0 – 1
UP
9 – 16
3
NEUTRAL
0 – 1
DOWN
9 – 16
Front power window motor (passenger side)
Front power window switch (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
D16
1
D10
5
Existed
3
4
Front power window motor (passenger side)
Ground
Continuity
Connector
Terminal
D16
1
Not existed
3
Revision: 2013 October
2014 JUKE
PWC-38
< DTC/CIRCUIT DIAGNOSIS >
POWER WINDOW MOTOR
Check rear power window motor LH operation with power window main switch or rear power window switch
LH.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
PWC-38, "REAR LH : Diagnosis Procedure"
REAR LH : Diagnosis Procedure
INFOID:0000000009753809
1.
CHECK REAR POWER WINDOW MOTOR LH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear power window motor LH connector.
3.
Turn ignition switch ON.
4.
Check voltage between rear power window motor LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window motor LH.
NO
>> GO TO 2.
2.
CHECK REAR POWER WINDOW MOTOR LH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect rear power window switch LH connector.
3.
Check continuity between rear power window motor LH harness connector and rear power window switch
LH harness connector.
4.
Check continuity between rear power window motor LH connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window switch LH.
NO
>> Repair or replace harness.
REAR RH
REAR RH : Component Function Check
INFOID:0000000009753810
1.
CHECK FUNCTION
Check rear power window motor RH operation with power window main switch or rear power window switch
RH.
Is the inspection result normal?
YES
>> INSPECTION END
(+)
(-)
Condition
Voltage (V)
Rear power window motor LH
Connector
Terminal
D67
1
Ground
Rear power win-
dow switch LH
NEUTRAL
0 – 1
DOWN
9 – 16
3
NEUTRAL
0 – 1
UP
9 – 16
Rear power window motor LH
Rear power window switch LH
Continuity
Connector
Terminal
Connector
Terminal
D67
1
D63
4
Existed
3
5
Rear power window motor LH
Ground
Continuity
Connector
Terminal
D67
1
Not existed
3
Revision: 2013 October
2014 JUKE
POWER WINDOW MOTOR
PWC-39
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
NO
>> Refer to
PWC-39, "REAR RH : Diagnosis Procedure"
.
REAR RH : Diagnosis Procedure
INFOID:0000000009753811
1.
CHECK REAR POWER WINDOW MOTOR RH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear power window motor RH connector.
3.
Turn ignition switch ON.
4.
Check voltage between rear power window motor RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window motor RH.
NO
>> GO TO 2.
2.
CHECK REAR POWER WINDOW MOTOR RH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect rear power window switch RH connector.
3.
Check continuity between rear power window motor RH harness connector and rear power window switch
RH harness connector.
4.
Check continuity between rear power window motor RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear power window switch RH.
NO
>> Repair or replace harness.
(+)
(-)
Condition
Voltage (V)
Rear power window motor RH
Connector
Terminal
D47
1
Ground
Rear power window
switch RH
NEUTRAL
0 – 1
DOWN
9 – 16
3
NEUTRAL
0 – 1
UP
9 – 16
Rear power window motor RH
Rear power window switch RH
Continuity
Connector
Terminal
Connector
Terminal
D47
1
D43
4
Existed
3
5
Rear power window motor RH
Ground
Continuity
Connector
Terminal
D47
1
Not existed
3
Revision: 2013 October
2014 JUKE
PWC-40
< DTC/CIRCUIT DIAGNOSIS >
ENCODER CIRCUIT
ENCODER CIRCUIT
Component Function Check
INFOID:0000000009753812
1.
CHECK FUNCTION
Check that front driver side door glass perform AUTO UP/DOWN operation normally when power window
main switch is operated.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009753813
1.
CHECK ENCODER PULSE SIGNAL
1.
Turn ignition switch ON.
2.
Check signal between power window main switch harness connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-55, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK ENCODER SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector and front power window motor (driver side) connector.
3.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
(+)
(-)
Signal
(Reference value)
Power window main switch
Connector
Terminal
D35
4
Ground
Refer to the following signal
5
JMKIA5210GB
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D35
4
D37
5
Existed
5
4
Power window main switch
Ground
Continuity
Connector
Terminal
D35
4
Not existed
5
Revision: 2013 October
2014 JUKE
ENCODER CIRCUIT
PWC-41
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK ENCODER POWER SUPPLY
1.
Connect power window main switch connector.
2.
Turn ignition switch ON.
3.
Check voltage between front power window motor (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK ENCODER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-55, "Removal and Installation"
NO
>> Repair or replace harness.
5.
CHECK ENCODER GROUND CIRCUIT 1
1.
Turn ignition switch OFF.
2.
Disconnect power window main switch connector.
3.
Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.
4.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK ENCODER GROUND CIRCUIT 2
1.
Connect power window main switch connector.
(+)
(-)
Voltage (V)
Front power window motor (driver side)
Connector
Terminal
D37
1
Ground
9 – 16
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D35
14
D37
1
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D35
14
Not existed
Power window main switch
Front power window motor (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D35
12
D37
6
Existed
Power window main switch
Ground
Continuity
Connector
Terminal
D35
12
Not existed
Revision: 2013 October
2014 JUKE
PWC-42
< DTC/CIRCUIT DIAGNOSIS >
ENCODER CIRCUIT
2.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace front power window motor (driver side).
NO
>> Replace power window main switch. Refer to
PWC-55, "Removal and Installation"
Power window main switch
Ground
Continuity
Connector
Terminal
D35
12
Existed
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст