Nissan Murano. Manual — part 1071
PCS-46
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
DIAGNOSIS SYSTEM (BCM)
WORK SUPPORT
SELF-DIAG RESULT
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
SELF-DIAG RESULTS
Displays the diagnosis results judged by BCM.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitor item
Description
REMO CONT ID CONFIR
It can be checked whether Intelligent Key ID code is registered or not in this mode.
AUTO LOCK SET
Auto door lock time can be changed in this mode.
• MODE 1: 1 minute
• MODE 2: 5 minutes
• MODE 3: 30 seconds
• MODE 4: 2 minutes
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch (driver side, passenger side and back door) mode
can be changed to operate (ON) or not operate (OFF) in this mode.
ENGINE START BY I-KEY
Engine start function mode can be changed to operate (ON) or not operate (OFF) with this mode.
TRUNK/GLASS HATCH OPEN
Buzzer reminder function mode by back door request switch can be changed to operate (ON) or
not operate (OFF) with this mode.
PANIC ALARM SET
Panic alarm button pressing time on Intelligent Key remote control button can be selected from the
following with this mode.
• MODE 1: 0.5 sec.
• MODE 2: Non-operation
• MODE 3: 1.5 sec.
PW DOWN SET
Unlock button pressing time on Intelligent Key button can be selected from the following with this
mode.
• MODE 1: 3 sec.
• MODE 2: Non-operation
• MODE 3: 5 sec.
TRUNK OPEN DELAY
NOTE:
This item is displayed, but cannot be supported.
LO- BATT OF KEY FOB WARN
Intelligent Key low battery warning mode can be changed to operate (ON) or not operate (OFF)
with this mode.
ANTI KEY LOCK IN FUNCTI
Key reminder function mode can be changed to operate (ON) or not operate (OFF) with this mode.
HAZARD ANSWER BACK
Hazard reminder function mode can be selected from the following with this mode.
• LOCK ONLY: Door lock operation only
• UNLOCK ONLY: Door unlock operation only
• LOCK/UNLOCK: Lock/unlock operation
• OFF: Non-operation
ANS BACK I-KEY LOCK
Buzzer reminder function (lock operation) mode by door request switch (driver side and passenger
side) can be selected from the following with this mode.
• Horn chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• OFF: Non-operation
ANS BACK I-KEY UNLOCK
Buzzer reminder function (unlock operation) mode by door request switch can be changed to op-
erate (ON) or not operate (OFF) with this mode.
SHORT CRANKING OUTPUT
Starter motor can operate during the times below.
• 70 msec
• 100 msec
• 200 msec
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis.
HORN WITH KEYLESS LOCK
Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not op-
erate (OFF) with this mode.
PCS
DIAGNOSIS SYSTEM (BCM)
PCS-47
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor Item
Condition
REQ SW -DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -RR
NOTE:
This item is displayed, but cannot be monitored.
REQ SW -RL
NOTE:
This item is displayed, but cannot be monitored.
REQ SW -BD/TR
Indicates [ON/OFF] condition of back door request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY2 -F/B
Indicates [ON/OFF] condition of ignition relay 2.
ACC RLY-FB
NOTE:
This item is displayed, but cannot be monitored.
CLUCH SW
NOTE:
This item is displayed, but cannot be monitored.
BRAKE SW 1
Indicates [ON/OFF]* condition of brake switch power supply.
BRAKE SW 2
Indicates [ON/OFF] condition of brake switch.
DETE/CANCL SW
Indicates [ON/OFF] condition of P position.
SFT PN/N SW
Indicates [ON/OFF] condition of P or N position.
S/L -LOCK
Indicates [ON/OFF] condition of steering lock unit (LOCK).
NOTE:
For models without steering lock unit this item is not displayed.
S/L -UNLOCK
Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
NOTE:
For models without steering lock unit this item is not displayed.
S/L RELAY -F/B
Indicates [ON/OFF] condition of ignition switch.
NOTE:
For models without steering lock unit this item is not displayed.
UNLK SEN -DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
PUSH SW -IPDM
Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY1 -F/B
Indicates [ON/OFF] condition of ignition relay 1.
DETE SW -IPDM
Indicates [ON/OFF] condition of P position.
SFT PN -IPDM
Indicates [ON/OFF] condition of P or N position.
SFT P -MET
Indicates [ON/OFF] condition of P position.
SFT N -MET
Indicates [ON/OFF] condition of N position.
ENGINE STATE
Indicates [STOP/START/CRANK/RUN] condition of engine states.
S/L LOCK-IPDM
Indicates [ON/OFF] condition of steering lock unit (LOCK).
NOTE:
For models without steering lock unit this item is not displayed.
S/L UNLK-IPDM
Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
NOTE:
For models without steering lock unit this item is not displayed.
S/L RELAY-REQ
Indicates [ON/OFF] condition of steering lock relay.
NOTE:
For models without steering lock unit this item is not displayed.
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h].
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].
PCS-48
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
DOOR STAT-DR
Indicates [LOCK/READY/UNLOCK] condition of driver side door status.
DOOR STAT-AS
Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.
ID OK FLAG
Indicates [SET/RESET] condition of key ID.
PRMT ENG STRT
Indicates [SET/RESET] condition of engine start possibility.
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored.
RKE-PANIC
Indicates [ON/OFF] condition of PANIC button of Intelligent Key.
RKE-P/W OPEN
Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.
RKE-MODE CHG
Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the
numerical value start changing.
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored.
Monitor Item
Condition
Test item
Description
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.
PW REMOTO DOWN SET
This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT screen is touched.
INSIDE BUZZER
This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT screen is touched.
• Key warning chime sounds when “KEY WARN” on CONSULT screen is touched.
• P position warning chime sounds when “P RNG WARN” on CONSULT screen is touched.
• ACC warning chime sounds when “ACC WARN” on CONSULT screen is touched.
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer will be activated after “ON” on CONSULT screen is touched.
INDICATOR
This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “KEY ON” on CONSULT screen is touched.
• “KEY” Warning lamp flashes when “KEY IND” on CONSULT screen is touched.
INT LAMP
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.
LCD
This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT screen is touched.
• Engine start information displays when “BP I” on CONSULT screen is touched.
• Key ID warning displays when “ID NG” on CONSULT screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT screen is touched.
NOTE:
For models without steering lock unit, “ROTAT” is displayed, but cannot be tested.
• P position warning displays when “SFT P” on CONSULT screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT screen is touched.
• Take away through window warning displays when “NO KY” on CONSULT screen is touched.
• Take away warning display when “OUTKEY” on CONSULT screen is touched.
• OFF position warning display when “LK WN” on CONSULT screen is touched.
PCS
DIAGNOSIS SYSTEM (BCM)
PCS-49
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
TRUNK/GLASS HATCH
This test is able to check back door opener actuator open operation.
This actuator opens when “ON” on CONSULT screen is touched.
FLASHER
This test is able to check hazard warning lamp operation.
The hazard warning lamps will be activated after “ON” on CONSULT screen is touched.
HORN
This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT screen is touched.
IGN CONT2
This test is able to check ignition relay operation.
The ignition relay will be activated after “ON” on CONSULT screen is touched.
P RANGE
This test is able to check CVT shift selector power supply
CVT shift selector power is supplied when “ON” on CONSULT screen is touched.
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched.
LOCK INDICATOR
NOTE:
This item is displayed, but cannot be tested.
ACC INDICATOR
This test is able to check indicator in push-ignition switch operation.
Indicator in push-button ignition switch illuminates when “ON” on CONSULT screen is touched.
IGNITION ON IND
This test is able to check indicator in push-ignition switch operation.
Indicator in push-button ignition switch illuminates when “ON” on CONSULT screen is touched.
KEY SLOT ILLUMI
This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT screen is touched.
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be tested.
AUTOMATIC SLIDING DOOR
NOTE:
This item is displayed, but cannot be tested.
Test item
Description
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст