Nissan Murano. Manual — part 1008

MIR-10

< SYSTEM DESCRIPTION >

[WITH ADP]

DIAGNOSIS SYSTEM (DRIVER SEAT CONTROL UNIT)

ACTIVE TEST

CAUTION:

When driving vehicle, do not perform active test.

WORK SUPPORT

IGN ON SW

“ON/OFF”

×

×

ON/OFF status judged from the ignition switch signal.

ACC ON SW

“ON/OFF”

×

×

ON/OFF status judged from the ACC switch signal.

KEY ON SW

“ON/OFF”

×

×

ON/OFF status judged from the key on switch signal.

KEYLESS ID

—

×

×

Key ID status judged from the key ID signal.

KYLS DR UNLK

“ON/OFF”

×

×

ON/OFF status judged from the driver side door unlock ac-
tuator output switch signal.

VHCL SPEED (ABS)

“ON/OFF”

×

×

ON/OFF status judged from vehicle speed signal.

HANDLE

“RHD/LHD”

×

×

RHD/LHD status judged from handle position signal.

TRANSMISSION

“AT or CVT/

MT”

×

×

AT or CVT/MT status judged from transmission.

STEERING STATUS

NOTE:
This item is displayed, but cannot monitored

Monitor Item

Unit

Main

Signals

Selection

From

Menu

Contents

Test item

Description

SEAT SLIDE

Activates/deactivates the sliding motor.

SEAT RECLINING

Activates/deactivates the reclining motor.

SEAT LIFTER FR

Activates/deactivates the lifting motor (front).

SEAT LIFTER RR

Activates/deactivates the lifting motor (rear).

TILT MOTOR

Activates/deactivates the tilt motor.

TELESCO MOTOR

Activates/deactivates the telescopic motor.

MIRROR MOTOR RH

Activates/deactivates the mirror motor (passenger side).

MIRROR MOTOR LH

Activates/deactivates the mirror motor (driver side).

MEMORY SW INDCTR

Turns ON/OFF the memory indicator.

Work item

Content

Item

SEAT SLIDE VOLUME SET

The amount of seat sliding for entry/exit assist can be selected
from 3 items.

40 mm

80 mm

150 mm

EXIT TILT SETTING

Entry/exit assist (steering column) can be selected:
ON (operated) – OFF (not operated)

ON

OFF

EXIT SEAT SLIDE SETTING

Entry/exit assist (seat) can be selected:
ON (operated) – OFF (not operated)

ON

OFF

DOOR MIRROR REMOTE CONTROL SWITCH

MIR-11

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

DTC/CIRCUIT DIAGNOSIS

DOOR MIRROR REMOTE CONTROL SWITCH

MIRROR SWITCH

MIRROR SWITCH : Description

INFOID:0000000009719322

It operates angle of the door mirror face.
It transmits mirror face adjust operation to AUTOMATIC DRIVE POSITIONER CONTROL UNIT.

MIRROR SWITCH : Component Function Check

INFOID:0000000009719323

1.

CHECK MIRROR SWITCH FUNCTION

Check the operation on “MIR CON SW–UP/DN” and “MIR CON SW–RH/LH” in “DATA MONITOR” mode
with CONSULT.

Is the inspection result normal?

YES

>> Mirror switch function is OK.

NO

>> Refer to

MIR-11, "MIRROR SWITCH : Diagnosis Procedure"

.

MIRROR SWITCH : Diagnosis Procedure

INFOID:0000000009719324

1.

CHECK MIRROR SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK MIRROR SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.

Monitor item

Condition

MIR CON SW-UP/DN

When operating the mirror switch toward the up or down side.

: ON

Other than above.

: OFF

MIR CON SW-RH/LH

When operating the mirror switch toward the right or left side.

: ON

Other than above.

: OFF

(+)

(–)

Voltage (V)

(Approx.)

Door mirror remote control switch

Connector

Terminal

D14

4

Ground

5

12

13

15

MIR-12

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

DOOR MIRROR REMOTE CONTROL SWITCH

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to

ADP-211, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK MIRROR SWITCH

Check door mirror remote control switch (mirror switch).
Refer to

MIR-12, "MIRROR SWITCH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace door mirror remote control switch (mirror switch). Refer to

MIR-75, "Removal and Instal-

lation"

.

5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to

GI-44, "Intermittent Incident"

.

>> INSPECTION END

MIRROR SWITCH : Component Inspection

INFOID:0000000009719325

1.

CHECK MIRROR SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Check continuity between door mirror remote control switch terminals.

Automatic drive positioner control unit Door

mirror

remote control switch

Continuity

Connector

Terminal

Connector

Terminal

M75

3

D14

15

Existed

4

13

15

12

16

4

Automatic drive positioner control unit

Ground

Continuity

Connector

Terminal

M75

3

Not existed

4

15

16

Door mirror remote control switch

Ground

Continuity

Connector

Terminal

D14

7

Existed

DOOR MIRROR REMOTE CONTROL SWITCH

MIR-13

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace door mirror remote control switch. Refer to

MIR-75, "Removal and Installation"

.

CHANGEOVER SWITCH

CHANGEOVER SWITCH : Description

INFOID:0000000009719326

Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.

CHANGEOVER SWITCH : Component Function Check

INFOID:0000000009719327

1.

CHECK CHANGEOVER SWITCH FUNCTION

Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT.

Is the inspection result normal?

YES

>> Changeover switch function is OK.

NO

>> Refer to

MIR-13, "CHANGEOVER SWITCH : Diagnosis Procedure"

.

CHANGEOVER SWITCH : Diagnosis Procedure

INFOID:0000000009719328

1.

CHECK CHANGEOVER SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CHANGEOVER SWITCH CIRCUIT

Door mirror remote control switch

Condition

Continuity

Connector

Terminal

D14

4

7

Mirror switch

RIGHT

Existed

Other than above

Not existed

13

LEFT

Existed

Other than above

Not existed

15

UP

Existed

Other than above

Not existed

12

DOWN

Existed

Other than above

Not existed

Monitor item

Condition

MIR CHNG SW-R/L

When operating the changeover toward the right or left side.

: ON

Other than above.

: OFF

(+)

(–)

Voltage (V)

(Approx.)

Door mirror remote control switch

Connector

Terminal

D14

10

Ground

5

11