Nissan Murano. Manual — part 696
EXL-196
< BASIC INSPECTION >
[HALOGEN TYPE]
DIAGNOSIS AND REPAIR WORK FLOW
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES
>> GO TO 8.
NO
>> Check according to
GI-44, "Intermittent Incident"
.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO
>> Before returning the vehicle to the customer, always erase DTC.
HEADLAMP SYSTEM
EXL-197
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SYSTEM DESCRIPTION
HEADLAMP SYSTEM
System Diagram
INFOID:0000000009722989
System Description
INFOID:0000000009722990
OUTLINE
Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP (LO) OPERATION
• BCM detects the combination switch condition with the combination switch reading function.
• BCM transmits the low beam request signal to IPDM E/R with CAN communication according to the head-
lamp (LO) ON condition.
Headlamp (LO) ON condition
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment (With auto light system)
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
HEADLAMP (HI) OPERATION
• BCM transmits the high beam request signal to IPDM E/R and the combination meter with CAN communica-
tion according to the headlamp (HI) ON condition.
Headlamp (HI) ON condition
- Lighting switch HI with the lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment (With auto light system)
- Lighting switch PASS
• Combination meter turns the high beam indicator lamp ON according to the high beam request signal.
• IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high
beam request signal.
JPLIA0167GB
EXL-198
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
HEADLAMP SYSTEM
Component Parts Location
INFOID:0000000009722991
Component Description
INFOID:0000000009722992
1.
Headlamp (HI)
2.
Headlamp (LO)
3.
Combination switch
4.
IPDM E/R
5.
BCM
6.
High beam indicator lamp
A.
Engine room (LH)
B.
Behind the combination meter
C.
On the combination meter
JPLIA0891ZZ
Part
Description
BCM
• Detects each switch condition by the combination switch reading function.
• Judges that the headlamp is turned ON according to the vehicle condition.
- Requests the headlamp relay (HI/LO) ON to IPDM E/R (with CAN communication).
- Requests the high beam indicator lamp ON to the combination meter (with CAN
communication).
IPDM E/R
Controls the integrated relay, and supplies voltage to the load according to the request
from BCM (with CAN communication).
Combination switch
(Lighting & turn signal switch)
Combination meter
(High beam indicator lamp)
Turns the high beam indicator lamp ON according to the request from BCM (with CAN
communication).
DAYTIME RUNNING LIGHT SYSTEM
EXL-199
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DAYTIME RUNNING LIGHT SYSTEM
System Diagram
INFOID:0000000009722993
System Description
INFOID:0000000009722994
OUTLINE
• Turns the front fog lamp ON as the daytime running light.
• Daytime running light is controlled by daytime running light control function and combination switch reading
function of BCM, and relay control function of IPDM E/R.
DAYTIME RUNNING LIGHT OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM detects the vehicle condition depending on the following signals.
- Engine condition signal (received from ECM with CAN communication)
- Parking brake switch signal (received from combination meter with CAN communication)
• BCM transmits the front fog light request signal to IPDM E/R with CAN communication according to the day-
time running light ON condition.
Daytime running light ON condition
- While the engine running with the parking brake released
Daytime running light OFF condition
- Engine stopped
- Headlamp ON (Passing included)
• IPDM E/R turns the integrated front fog lamp relay ON and turns the front fog lamp ON according to the front
fog light request signal.
JPLIA0803GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст