Nissan Murano. Manual — part 1188
REAR SHOCK ABSORBER
RSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
1.
Wrap a shop cloth around lower side of shock absorber and fix it with a vise.
CAUTION:
Never set the cylindrical part of shock absorber with a vise.
2.
Secure the piston rod tip so that piston rod does not turn, and remove piston rod lock nut.
3.
Remove mounting bracket and bound bumper from shock absorber.
ASSEMBLY
Install in the reverse order of disassembly.
Inspection
INFOID:0000000009721432
INSPECTION AFTER REMOVAL
Check the following items, and replace the parts if necessary.
• Shock absorber assembly for deformation, cracks, damage.
• Welded and sealed areas for oil leakage.
• Piston rod for damage, uneven wear or distortion.
• Seal of shock absorber mounting bracket for cracks, damage and come off.
INSPECTION AFTER DISASSEMBLY
Bound Bumper
Check bound bumper for cracks and damage. Replace it if necessary.
Shock Absorber
Check the following items, and replace the part if necessary.
• Shock absorber for deformation, cracks, and other damage.
• Piston rod for damage, uneven wear, and distortion.
INSPECTION AFTER ASSEMBLY
Make sure piston rod on shock absorber is not damaged when attaching components to shock absorber.
INSPECTION AFTER INSTALLATION
1.
Check wheel alignment. Refer to
2.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
Disposal
INFOID:0000000009721433
1.
Set shock absorber horizontally with the piston rod fully extended.
2.
Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position (
) from top
as shown in the figure to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction (
).
• Directly to the outer tube avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3.
Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
A
: 20 – 30 mm (0.79 – 1.18 in)
JPEIA0161ZZ
RSU-12
< REMOVAL AND INSTALLATION >
RADIUS ROD
RADIUS ROD
Exploded View
INFOID:0000000009721434
Removal and Installation
INFOID:0000000009721435
REMOVAL
1.
Remove tire with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-124, "REAR WHEEL SENSOR : Exploded
.
3.
Remove rear lower link and coil spring. Refer to
4.
Remove shock absorber mounting bolt (lower side) with power tool. Refer to
5.
Remove front lower link mounting bolt and nut (axle housing side) with power tool. Refer to
6.
Loosen front lower link mounting bolt and nut (suspension member side). Refer to
.
7.
Remove radius rod mounting bolts and nuts (axle housing side) with power tool.
8.
Remove radius rod mounting bolt (rear suspension member side) with power tool, then remove radius
rod.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
Inspection
INFOID:0000000009721436
INSPECTION AFTER REMOVAL
Check radius rod and bushing for any deformation, cracks, or damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
1.
Upper seat
2.
Coil spring
3.
Rubber seat
4.
Rear lower link
5.
Rear suspension member
6.
Radius rod
7.
Front lower link
Refer to
for symbols in the figure.
JPEIB0146GB
RADIUS ROD
RSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
RSU-14
< REMOVAL AND INSTALLATION >
FRONT LOWER LINK
FRONT LOWER LINK
Exploded View
INFOID:0000000009721437
Removal and Installation
INFOID:0000000009721438
REMOVAL
1.
Remove tire with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-124, "REAR WHEEL SENSOR : Exploded
.
3.
Remove rear lower link and coil spring. Refer to
4.
Remove shock absorber mounting bolt (lower side) with power tool. Refer to
5.
Remove stabilizer bushing and stabilizer clamp. Refer to
.
6.
Remove front lower link mounting bolts and nuts (rear suspension member side) with power tool.
7.
Remove front lower link mounting bolts and nuts (axle housing side) with power tool.
8.
Remove front lower link.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
Inspection
INFOID:0000000009721439
INSPECTION AFTER REMOVAL
Check front lower link and bushing for any deformation, cracks, or damage. Replace if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
BRC-9, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
1.
Upper seat
2.
Coil spring
3.
Rubber seat
4.
Rear lower link
5.
Rear suspension member
6.
Radius rod
7.
Front lower link
Refer to
for symbols in the figure.
JPEIB0146GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст