Nissan Murano. Manual — part 1409
TM-178
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
CVT FLUID FILTER
CVT FLUID FILTER
Exploded View
INFOID:0000000010106055
Removal and Installation
INFOID:0000000010106056
NOTE:
Cap or plug openings to prevent fluid from spilling.
REMOVAL
1.
Remove front fender protector LH. Refer to
EXT-26, "FENDER PROTECTOR : Exploded View"
2.
Pull out CVT fluid cooler hose from CVT fluid filter.
3.
Remove filter hose.
4.
Remove CVT fluid filter from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Never reuse hose clamp.
1.
Transaxle
2.
CVT fluid filter
3.
Hose clamp
4.
Filter hose
Refer to
for symbols in the figure.
JSDIA4011GB
CVT FLUID FILTER
TM-179
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Install filter hose (1) and hose clamps (2) as shown in the figure.
A
: Paint mark
JSDIA4012ZZ
TM-180
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
TRANSAXLE ASSEMBLY
UNIT REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000009719595
Removal and Installation
INFOID:0000000009719596
WARNING:
Never remove the reservoir tank cap when the engine is hot. Serious burns could occur from high-
pressure engine coolant escaping from the reservoir tank.
CAUTION:
• Perform this step engine is cold.
• When replacing TCM and transaxle assembly as a set, replace transaxle assembly first and then
replace TCM. Refer to
.
REMOVAL
1.
Air breather hose
2.
CVT fluid level gauge
3.
CVT fluid charging pipe
4.
O-ring
5.
Copper washer
6.
fluid cooler tube
7.
Transaxle assembly
A.
For tightening torque, refer to
TM-180, "Removal and Installation"
.
for symbols in the figure.
JPDIA0626GB
TRANSAXLE ASSEMBLY
TM-181
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Remove the engine, the transaxle, transfer (AWD models) assembly and front suspension member. Refer
to
(AWD).
2.
Lift with hoist and separate engine, transaxle and transfer (AWD models) assembly from front suspension
member. Refer to
(2WD),
(AWD).
3.
Remove air breather hose. Refer to
4.
Disconnect secondary speed sensor connector. Refer to
5.
Disconnect CVT unit connector.
6.
Disconnect air fuel ratio sensor 1 (bank 2). Refer to
.
7.
Remove crankshaft position sensor (POS). Refer to
8.
Remove CVT fluid charging pipe from transaxle assembly.
9.
Remove transaxle assembly fixing bolts with power tool.
10. Remove transaxle assembly from engine assembly with a hoist.
11. Remove CVT fluid cooler hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply petroleum jelly to O-ring.
• Check fitting of dowel pins (
) when installing transaxle assembly
to engine assembly.
• When installing CVT fluid cooler tube (1) to transaxle assembly:
- Contact CVT fluid cooler tube a boss portion (A) of the transaxle
case.
- Tighten the bolt of CVT fluid cooler tube without moving the CVT
fluid cooler tube.
• When installing transaxle assembly to the engine assembly, attach the fixing bolts in accordance with the fol-
lowing.
1.
Rotate torque converter to align a torque converter stud bolt with the service hole.
2.
Rotate drive plate to align a torque converter stud bolt insertion hole of drive plate with service hole.
3.
Install transaxle to engine.
JPDIA0598ZZ
JPDIA0602ZZ
JPDIA0628ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст