Nissan Murano. Manual — part 1023
MIR-70
< REMOVAL AND INSTALLATION >
[WITH ADP]
INSIDE MIRROR
REMOVAL AND INSTALLATION
INSIDE MIRROR
Exploded View
INFOID:0000000009719350
Removal and Installation
INFOID:0000000009719351
CAUTION:
Never reuse the inside mirror disassembled from mirror base.
REMOVAL
1.
Remove the inside mirror cover.
2.
Remove TORX bolt.
3.
Slide the inside mirror upward to remove.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When inserting the inside mirror into the mirror base, be sure to push the pawl until it get connected to
the mirror base.
1.
Inside mirror
2.
Inside mirror cover
3.
Mirror base
4.
TORX bolt
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
JMLIA0136GB
OUTSIDE MIRROR
MIR-71
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
OUTSIDE MIRROR
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Exploded View
INFOID:0000000009719352
REMOVAL
DISASSEMBLY
1.
Door mirror assembly
2.
Front door assembly
3.
Door mirror corner cover
4.
Door mirror corner cover
(with BSW indicator)
5.
BSW indicator assembly
: Clip
JMLIA3464ZZ
JMLIA0123ZZ
MIR-72
< REMOVAL AND INSTALLATION >
[WITH ADP]
OUTSIDE MIRROR
DOOR MIRROR ASSEMBLY : Removal and Installation
INFOID:0000000009719353
CAUTION:
Never damage the mirror bodies.
REMOVAL
1.
Remove the front door finisher. Refer to
INT-13, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Disconnect BSW indicator harness connector (with BSW indicator models).
3.
Disengage the fixing clips and remove the door mirror corner cover.
4.
Disconnect the door mirror harness connector.
5.
Remove the door mirror mounting nuts, and remove the door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
GLASS MIRROR
GLASS MIRROR : Exploded View
INFOID:0000000009719354
GLASS MIRROR : Disassembly and Assembly
INFOID:0000000009719355
CAUTION:
Never damage the mirror bodies.
DISASSEMBLY
1.
Door mirror cover
2.
Door mirror assembly
3.
Glass mirror
: Pawl
1.
Door mirror cover
2.
Door mirror assembly
3.
Glass mirror
: Pawl
JMLIA0123ZZ
OUTSIDE MIRROR
MIR-73
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
1.
Place the glass mirror upward.
2.
Put a strip of protective tape (A) on the housing.
3.
Insert flat-bladed screwdriver (B) into the recess at lower side
between glass mirror (1) and actuator (2), and push up pawls to
remove glass mirror lower side.
NOTE:
Insert a small slotted screwdriver into recess, and push up while
rotating (twist) to make work easier.
4.
Insert flat-bladed screwdriver at RH/LH side between glass mirror and actuator, and push up pawls to
remove glass mirror RH/LH side.
NOTE:
Insert flat-bladed screwdriver into recesses, and push up while rotating (twist) to make work easier.
5.
Remove two terminals of mirror heater attachment. (With heater mirror model)
6.
Pull glass mirror as shown in the figure in order to disengage
both upper pawls, and then remove glass mirror.
ASSEMBLY
Install in the reverse order of removal.
CAUTION:
After installation, visually check that pawls are securely engaged.
DOOR MIRROR COVER
JMLIA0124ZZ
1.
Glass mirror
2.
Actuator
JMLIA0092ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст