Nissan Murano. Manual — part 767
FL-8
< REMOVAL AND INSTALLATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
• To keep the connecting portion clean and to avoid dam-
age and foreign materials, cover them completely with
plastic bags (A) or something similar.
8.
Remove retainer for main fuel level sensor unit, fuel filter and
fuel pump assembly and sub fuel level sensor unit with fuel tank
lock ring wrench (SST) by turning counterclockwise.
9.
Remove main fuel level sensor unit, fuel filter and fuel pump assembly, and sub fuel level sensor unit.
• Raise main fuel level sensor unit, fuel filter and fuel pump
assembly, and disconnect fuel hose connector (push in tabs
and pull out) and sub fuel level sensor unit harness connector.
• Raise and release sub fuel level sensor unit to remove.
INSTALLATION
Note to the following, and install in the reverse order of removal.
Main and Sub Fuel Level Sensor Unit
1.
Install new seal packing to fuel tank without any twist.
2.
Connect fuel hose connector (push in until it stops) and sub fuel
level sensor unit harness connector.
NOTE:
When installing fuel hose connector insert them fully until a click
sound of full stopper engagement is heard.
JPBIA0135ZZ
SBIA0411E
SBIA0396E
SBIA0398E
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-9
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
3.
Align the direction mark on main fuel level sensor unit, fuel filter
and fuel pump assembly and sub fuel level sensor unit with that
on fuel tank as shown in the figure, and install them to fuel tank.
CAUTION:
• Never allow seal packing to drop.
• Never bend float arm during installing.
4.
Install retainer for main fuel level sensor unit, fuel filter and fuel
pump assembly and sub fuel level sensor unit with fuel tank lock
ring wrench (SST) by turning clockwise.
CAUTION:
Install retainer horizontally.
Quick Connector
Connect quick connector as follows:
1.
Check the connection for damage or any foreign materials.
2.
Align the connector with the tube, then insert the connector straight into the tube until a click sound is
heard.
3.
After connecting, check that the connection is secure by following method.
• Pull (A) the tube and the connector to check they are securely
connected.
• Visually confirm that the two retainer tabs are connected to the
connector.
Disassembly and Assembly
INFOID:0000000009720457
DISASSEMBLY
Fuel level sensor unit, fuel filter and fuel pump assembly side
1.
Disconnect harness connector.
2.
Remove fuel level sensor unit according to the following procedure.
SBIA0397E
SBIA0411E
JPBIA0140ZZ
FL-10
< REMOVAL AND INSTALLATION >
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
a.
Push the pawl of fuel level sensor unit (1) mounting area with an
L-shaped iron rod or an equivalent to unlock.
CAUTION:
Be careful not to damage it.
b.
With the fuel level sensor unit unlocked, slide it in the direction
shown by the arrow (
).
Sub fuel level sensor unit assembly side
1.
Remove sub fuel level sensor unit according to the following procedure.
a.
Push the pawl of sub fuel level sensor unit (1) mounting area
with an L-shaped iron rod or an equivalent to unlock.
CAUTION:
Be careful not to damage it.
b.
With the sub fuel level sensor unit unlocked, slide it in the direc-
tion shown by the arrow (
).
ASSEMBLY
Install fuel level sensor unit and sub fuel level sensor unit according to the following procedure.
• Insert fuel level sensor unit and sub fuel level sensor unit all the way to the end until a “click” touch and
sound can be recognized.
• Pull fuel level sensor unit and sub fuel level sensor unit in the removal direction to ensure that they do not
become detached.
Inspection
INFOID:0000000009720458
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leakage.
1.
Turn ignition switch “ON” (with engine stopped), then check connections for leakage by applying fuel pres-
sure to fuel piping.
2.
Start engine and let it idle and check there are no fuel leakage at the fuel system connections.
PBIC4900J
PBIC4899J
FUEL TANK
FL-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
FUEL TANK
Exploded View
INFOID:0000000009720459
Removal and Installation
INFOID:0000000009720460
WARNING:
Be sure to read “General Precautions” when working on the fuel system. Refer to
.
REMOVAL
• Drain fuel from fuel tank if necessary. Refer to
FL-6, "Removal and Installation"
.
• Perform work on level place.
1.
Perform steps 2 to 7 of “REMOVAL” in “ FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP
ASSEMBLY” on main and sub fuel level sensor units. Refer to
FL-6, "Removal and Installation"
2.
Remove center muffler. Refer to
3.
Remove propeller shaft. Refer to
. (AWD models)
1.
Clamp
2.
EVAP/Vent line hose
3.
Fuel tank
4.
Fuel tank mounting band (RH)
5.
Fuel tank protector
6.
Fuel tank protector (RH)
7.
Fuel tank protector (LH)
8.
Fuel tank mounting band (LH)
9.
Clamp
10. Clamp
11.
Fuel filler hose
12. EVAP (Recirculation) hose
13. Clamp
14.
Fuel filler tube
15. Grommet
16. Fuel filler cap
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSBIA4294GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст