Nissan Murano. Manual — part 1392
TM-110
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
SHIFT LOCK SYSTEM
Component Function Check
INFOID:0000000009719530
1.
CHECK CVT SHIFT LOCK OPERATION
1.
Turn ignition switch ON.
2.
Move selector lever to “P” position.
3.
Attempt to shift selector lever to any other position with brake pedal released.
Can selector lever be shifted to any other position?
JRDWC1703GB
SHIFT LOCK SYSTEM
TM-111
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
YES
>> Go to
.
NO
>> GO TO 2.
2.
CHECK CVT SHIFT LOCK OPERATION
Attempt to shift selector lever to any other position with brake pedal depressed.
Can the selector lever be shifted to any other position?
YES
>> INSPECTION END
NO
>> Go to
.
Diagnosis Procedure
INFOID:0000000009719531
1.
CHECK POWER SOURCE
1.
Turn ignition switch OFF.
2.
Disconnect fuse block (J/B) connector.
3.
Turn ignition switch ON.
4.
Check voltage between fuse block (J/B) connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>>
Check the following.
• 10A fuse [No. 3, located in fuse block (J/B)]
• Ignition switch
2.
CHECK HARNESS BETWEEN FUSE BLOCK (J/B) AND STOP LAMP SWITCH (PART 1)
1.
Turn ignition switch OFF.
2.
Disconnect stop lamp switch connector.
3.
Check continuity between fuse block (J/B) vehicle side harness connector terminal and stop lamp switch
vehicle side harness connector terminal.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK HARNESS BETWEEN FUSE BLOCK (J/B) AND STOP LAMP SWITCH (PART 2)
Check continuity between stop lamp switch vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to
TM-113, "Component Inspection (Stop Lamp Switch)"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace stop lamp switch. Refer to
.
Fuse block (J/B) connector
Ground
Voltage (Approx.)
Connector
Terminal
E103
4F
Battery voltage
Fuse block (J/B) vehicle side harness connector
Stop lamp switch vehicle side harness connector
Continuity
Connector
Terminal
Connector
Terminal
E103
4F
E116
3
Existed
Stop lamp switch vehicle side harness connector
Ground
Continuity
Connector
Terminal
E116
3
Not existed
TM-112
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
SHIFT LOCK SYSTEM
5.
CHECK HARNESS BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 1)
1.
Disconnect CVT shift selector connector.
2.
Check continuity between stop lamp switch vehicle side harness connector terminal and CVT shift selec-
tor vehicle side harness connector terminal.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace damaged parts.
6.
CHECK HARNESS BETWEEN STOP LAMP SWITCH AND CVT SHIFT SELECTOR (PART 2)
Check continuity between control vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace damaged parts.
7.
CHECK GROUND CIRCUIT
Check continuity between CVT shift selector vehicle side harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace damaged parts.
8.
CHECK CVT SHIFT SELECTOR
1.
Shift selector lever to “P” position.
2.
Check continuity between CVT shift selector connector terminals.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Replace CVT shift selector. Refer to
9.
CHECK SHIFT LOCK SOLENOID
1.
Remove shift lock unit. Refer to
2.
Check shift lock solenoid. Refer to
TM-113, "Component Inspection (Shift Lock Solenoid)"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace damaged parts.
Stop lamp switch vehicle side harness connector
CVT shift selector vehicle side harness connec-
tor
Continuity
Connector
Terminal
Connector
Terminal
E116
4
M57
6
Existed
CVT shift selector vehicle side harness connector
Ground
Continuity
Connector
Terminal
M57
6
Not existed
CVT shift selector vehicle side harness connector
Ground
Continuity
Connector
Terminal
M57
7
Existed
CVT shift selector connector
Continuity
Connector
Terminal
M57
6
7
Existed
SHIFT LOCK SYSTEM
TM-113
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Component Inspection (Stop Lamp Switch)
INFOID:0000000009719532
1.
CHECK STOP LAMP SWITCH
Check continuity between stop lamp switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace stop lamp switch. Refer to
.
Component Inspection (Shift Lock relay)
INFOID:0000000009719533
1.
CHECK SHIFT LOCK RELAY
Apply voltage to terminals of shift lock relay connector to check the continuity.
CAUTION:
Connect the fuse between the terminals when applying the voltage.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace shift lock relay.
Component Inspection (Shift Lock Solenoid)
INFOID:0000000009719534
1.
CHECK SHIFT LOCK SOLENOID
Apply voltage to CVT shift selector connector terminals and then check that shift lock solenoid is activated.
CAUTION:
Connect the fuse between the terminals when applying the voltage.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace shift lock unit. Refer to
.
Stop lamp switch connector
Condition
Continuity
Connector
Terminal
E116
3
4
Depressed brake pedal
Existed
Released brake pedal
Not existed
Shift lock relay connector
Condition
Continuity
Connector
Terminal
E53
5
3
Apply 12 V direct voltage between terminals 2 and 1.
Existed
(+) (fuse)
(
−
)
Condition
Status
CVT shift selector connector
Connector
Terminal
M57
6
7
• Park switch: ON
• Apply 12 V direct current be-
tween terminals 6 and 7.
Shift lock solenoid operates
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст