Nissan Murano. Manual — part 1492
WW-36
< DTC/CIRCUIT DIAGNOSIS >
FRONT WIPER MOTOR GROUND CIRCUIT
FRONT WIPER MOTOR GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000009719736
1.
CHECK FRONT WIPER MOTOR (GROUND) OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect front wiper motor connector.
3.
Check continuity between front wiper motor harness connector and ground.
Does continuity exist?
YES
>> Front wiper motor ground circuit is normal.
NO
>> Repair the harness or connector.
Front wiper motor
Ground
Continuity
Connector
Terminal
E12
2
Existed
WASHER SWITCH
WW-37
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER SWITCH
Description
INFOID:0000000009719737
• Washer switch is integrated with combination switch.
• Combination switch switches polarity between front washer operating and rear washer operating to supply
power to the washer pump on ground.
Component Inspection
INFOID:0000000009719738
1.
CHECK WIPER SWITCH
1.
Turn the ignition switch OFF.
2.
Disconnect combination switch connector.
3.
Check continuity between the combination switch terminals.
Does continuity exist?
YES
>> Wiper and washer switch is normal.
NO
>> Replace combination switch (Wiper and washer switch).
JPLIA0163GB
A
: Terminal 4
B
: Terminal 6
C
: Terminal 3
D
: Terminal 1
JPLIA0164GB
Combination switch
Condition
Continuity
Terminal
1
6
Front washer switch ON
Existed
3
4
1
4
Rear washer switch ON
3
6
WW-38
< DTC/CIRCUIT DIAGNOSIS >
RAIN SENSOR
RAIN SENSOR
Description
INFOID:0000000009719739
Rain sensor judges a wiping speed for front wiper by rain condition
and the vehicle conditions. And it transmits the wiping speed request
signal to the BCM via the rain sensor serial link.
Component Function Check
INFOID:0000000009719740
1.
CHECK FRONT WIPER AUTO OPERATION
1.
Clean rain sensor detection area of windshield fully.
2.
When the front wiper switch is turned to INT/AUTO position, front wiper operates once regardless of a
rainy condition.
Is front wiper (AUTO) operation normally?
YES
>> Rain sensor circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009719741
1.
CHECK RAIN SENSOR FUSE
1.
Turn the ignition switch OFF.
2.
Check that the rain sensor 10 A fuse (#6) is not fusing.
Is the fuse fusing?
YES
>> Replace the fuse after repairing the applicable circuit.
NO
>> GO TO 2.
2.
CHECK RAIN SENSOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect rain sensor connector.
3.
Turn ignition switch ON.
4.
Check voltage between rain sensor harness connector and ground.
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK RAIN SENSOR GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between rain sensor harness connector and ground.
JSLIA0093ZZ
Terminal
Voltage (Approx.)
(+)
(
−
)
Rain sensor connector
Terminal
R23
1
Ground Battery
voltage
RAIN SENSOR
WW-39
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Does continuity exist?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK RAIN SENSOR SIGNAL
1.
Connect rain sensor connector.
2.
Turn ignition switch ON.
3.
Check signal between BCM harness connector and ground with oscilloscope.
Is the measurement value normal?
YES
>> Replace rain sensor. Refer to
.
NO
>> GO TO 5.
5.
CHECK RAIN SENSOR SIGNAL CIRCUIT FOR OPEN
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and rain sensor harness connector.
Does continuity exist?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK RAIN SENSOR SIGNAL CIRCUIT FOR SHORT
Check continuity between BCM harness connector and ground.
Does continuity exist?
YES
>> Repair or replace harness.
NO
>> Replace BCM. Refer to
.
Rain sensor
Ground
Continuity
Connector
Terminal
R23
3
Existed
Terminal
Condition
Signal
(Reference value)
(+)
(
−
)
BCM
connector
Terminal
M123
112
Ground
Ignition
switch ON
Approx. 8.7V
JPMIA0156GB
BCM
Rain sensor
Continuity
Connector
Terminal
Connector
Terminal
M123
112
R23
2
Existed
BCM
Ground
Continuity
Connector
Terminal
M123
112
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст