Nissan Murano. Manual — part 1155
RF-4
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000009719644
Initialization of system should be conducted after the following conditions.
• When the sunroof motor or sunshade motor is changed.
• When the sunroof of sunshade does not operate normally. (Incomplete initialization conditions)
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000009719645
INITIALIZATION PROCEDURE
If the sunroof or sunshade does not close or open automatically, use the following procedure to return sunroof
or sunshade operation to normal.
1.
Close the sunroof and sunshade, then release the sunroof switch once.
2.
Press and hold the sunroof switch CLOSE (1st or 2nd) again (for approx. 10 seconds), then sunroof will
move to forward and it will be stopped mechanically.
3.
Release the sunroof switch, and press and hold the sunroof switch CLOSE (1st or 2nd) again. then sun-
roof and sunshade will automatically move to fully closed
⇒
fully open
⇒
fully closed.
4.
Release sunroof switch, after the sunroof is fully closed.
5.
Check sunroof and sunshade operation.
CHECK ANTI-PINCH FUNCTION
1.
Full open the sunroof.
2.
Place a piece of wood near fully closed position.
3.
Close the sunroof completely with auto-slide close.
4.
Check that sunroof lowers for approximately 150 mm (5.91in) or 2 seconds with out pinching a piece of
wood and stop.
5.
Full open the sunshade.
6.
Place a piece of wood near fully closed position.
7.
Close the sunroof completely with auto-slide close.
8.
Check that sunroof lowers for approximately 150 mm (5.91in) or 2 seconds with out pinching a piece of
wood and stop.
CAUTION:
• Never check with hands and other part of body because they may be pinched. Never get pinched.
• Depending on environment and driving conditions, if a similar impact or lord is applied to the sun-
roof it may lower.
• Check that auto-slide operates before inspection when system initialization is performed.
• Perform initial setting when auto-slide operation or anti-pinch function does not operate normally.
SUNROOF SYSTEM
RF-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
SYSTEM DESCRIPTION
SUNROOF SYSTEM
System Diagram
INFOID:0000000009719646
SUNROOF
System Description
INFOID:0000000009719647
DESCRIPTION
• Sunroof motor assembly and sunshade motor assembly operate with the power supplied from BCM while
ignition switch is ON or retained power is operating.
• Sunroof motor assembly receives an operation signal from sunroof switch, and sends the signal to sunshade
motor by communication line.
• Sunroof motor assembly and sunshade motor assembly receive a vehicle speed signal from combination
meter and controls the sunroof motor and sunshade motor torque at the time of high speed operation.
• The sunroof switch can be operated in the directions of push, open (1st, 2nd) and close (1st, 2nd). It can
operate the sunroof and sunshade by one switch.
OPERATION DESCRIPTION
The sunroof and sunshade operate as per the following by operating the sunroof switch operation.
JMKIA2654GB
(1)
PUSH
(2)
OPEN 1st
(3)
OPEN 2nd
(4)
CLOSE 1st
(5)
CLOSE 2nd
JMKIA1883ZZ
RF-6
< SYSTEM DESCRIPTION >
SUNROOF SYSTEM
Before Operation
Switch condition
Roof and sunshade operation
After Operation
OPEN: 1st
Opens the sunshade
OPEN: 2nd
The sunshade opens, and
then the sunroof opens.
PUSH
The sunshade opens, and
then the sunroof tilts up.
OPEN: 1st
Opens the sunroof
PUSH
Tilts down
CLOSE: 1st
CLOSE: 2nd
The sunroof tilts down, and
then sunshade closes.
JMKIA2617GB
JMKIA2619ZZ
JMKIA2620ZZ
JMKIA2621ZZ
JMKIA2627GB
JMKIA2628ZZ
JMKIA2618GB
JMKIA2622ZZ
JMKIA2623ZZ
SUNROOF SYSTEM
RF-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
AUTO OPERATION
The sunroof or sunshade operates automatically to the fully-open or fully-close position by operating the sun-
roof switch to the OPEN (2nd) or CLOSE (2nd) position.
RETAINED POWER OPERATION
Retained power operation is an additional power supply function that enables sunroof system to operate for 45
seconds period after ignition switch is turned OFF.
Retained power function cancel conditions
• Front door CLOSE (door switch OFF)
→
OPEN (door switch ON)
• Ignition switch is ON again.
• Timer passed. (45 seconds)
ANTI-PINCH FUNCTION
CAUTION:
There are some small distances immediately before the closed position which cannot be detected.
• The CPU of sunroof motor assembly monitor the sunroof condition by the signals from sunroof motor. When
sunroof motor assembly detects an interruption during auto operation (close or tilt down operation), sunroof
motor will tilt up or open [150 mm (5.91 in) or more] sunroof.
• The CPU of sunshade motor assembly monitor the sunshade condition by the signals from sunshade motor.
When sunshade motor assembly detects an interruption during auto close operation, sunroof motor will open
[150 mm (5.91 in) or more] sunshade.
Component Parts Location
INFOID:0000000009719648
PUSH
Tilts up
CLOSE: 1st
Closes the sunroof
CLOSE: 2nd
The sunroof closes, and then
the sunshade closes.
CLOSE: 1st
Closes the sunshade
Before Operation
Switch condition
Roof and sunshade operation
After Operation
JMKIA2624GB
JMKIA2625ZZ
JMKIA2622ZZ
JMKIA2626ZZ
JMKIA2627GB
JMKIA2629ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст