Nissan Murano. Manual — part 560
EC-350
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0605 ECM
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009720082
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Perform DTC CONFIRMATION PROCEDURE.
See
Is the 1st trip DTC P0605 displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
Go to
EC-16, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
>> INSPECTION END
P0607 ECM
EC-351
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0607 ECM
Description
INFOID:0000000009720083
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
DTC Logic
INFOID:0000000009720084
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009720085
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Erase DTC.
3.
Perform DTC CONFIRMATION PROCEDURE.
See
.
4.
Check DTC.
Is the DTC P0607 displayed again?
Yes
>> GO TO 2.
No
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
Go to
EC-16, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
.
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0607
CAN communication bus
When detecting error during the initial diagno-
sis of CAN controller of ECM.
• ECM
EC-352
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0643 SENSOR POWER SUPPLY
P0643 SENSOR POWER SUPPLY
DTC Logic
INFOID:0000000009720086
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for 1 second.
2.
Check DTC
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009720087
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection E38. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK ACCELERATOR PEDAL POSITION SENSOR 1 POWER SUPPLY CIRCUIT
1.
Disconnect accelerator pedal position (APP) sensor harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between APP sensor harness connector and ground.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
P0643
Sensor power supply
circuit short
ECM detects that the voltage of power
source for sensor is excessively low or high.
• Harness or connectors
(APP sensor 1 circuit is shorted.)
(TP sensor circuit is shorted.)
[CMP sensor (PHASE) circuit is shorted.)
(PSP sensor circuit is shorted.)
(Battery current sensor circuit is shorted.)
• Accelerator pedal position sensor
• Throttle position sensor
• Camshaft position sensor (PHASE)
• Power steering pressure sensor
• Battery current sensor
APP sensor
Ground
Voltage (V)
Connector
Terminal
E110
4
Ground
Approx. 5
P0643 SENSOR POWER SUPPLY
EC-353
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 3.
3.
CHECK SENSOR POWER SUPPLY CIRCUIT
Check harness for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair short to ground or short to power in harness or connectors.
4.
CHECK COMPONENTS
Check the following.
• Camshaft position sensor (PHASE) (Refer to
EC-281, "Component Inspection"
• Battery current sensor (Refer to
EC-369, "Component Inspection"
.)
• Power steering pressure sensor (Refer to
EC-345, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace malfunctioning component.
5.
CHECK TP SENSOR
EC-190, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 6.
6.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace electric throttle control actuator. Refer to
.
2.
Go to
EC-190, "Special Repair Requirement"
.
>> INSPECTION END
7.
CHECK APP SENSOR
EC-421, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> GO TO 8.
8.
REPLACE ACCELERATOR PEDAL ASSEMBLY
1.
Replace accelerator pedal assembly. Refer to
.
2.
Go to
EC-421, "Special Repair Requirement"
.
>> INSPECTION END
9.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
ECM
Sensor
Connector
Terminal
Name
Connector
Terminal
F8
47
TP sensor
F29
1
51
Battery current sensor
F76
1
55
PSP sensor
F62
3
59
CMP sensor (PHASE) (bank 1)
F26
1
63
CMP sensor (PHASE) (bank 2)
F69
1
E16
83
APP sensor
E110
4
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст