Nissan Murano. Manual — part 1467
WCS-90
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
JRMWE5838GB
WCS
BCM (BODY CONTROL MODULE)
WCS-91
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
JRMWE5839GB
WCS-92
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
Fail-safe
INFOID:0000000010088792
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC are detected.
JRMWE5840GB
WCS
BCM (BODY CONTROL MODULE)
WCS-93
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
HIGH FLASHER OPERATION
BCM detects the turn signal lamp circuit status by the current value.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE:
The blinking speed is normal while activating the hazard warning lamp.
FAIL-SAFE CONTROL BY RAIN SENSOR MALFUNCTION
• BCM judges the rain sensor serial link error by the rain sensor serial link condition and detects the rain sen-
sor malfunction by rain sensor malfunction signal.
• When BCM detects the rain sensor serial link error or the rain sensor malfunction while front wiper AUTO
operation, BCM operates a fail-safe control.
NOTE:
If rain sensor malfunction is detected when ignition switch is turned OFF
⇒
ON and front wiper switch is INT/
AUTO position, BCM operates a fail-safe control.
REAR WIPER MOTOR PROTECTION
BCM detects the rear wiper stopping position according to the rear wiper stop position signal.
When the rear wiper stop position signal does not change for more than 5 seconds while driving the rear
wiper, BCM stops power supply to protect the rear wiper motor.
Condition of cancellation
1.
More than 1 minute is passed after the rear wiper stop.
2.
Turn rear wiper switch OFF.
3.
Operate the rear wiper switch or rear washer switch.
DTC Inspection Priority Chart
INFOID:0000000010088793
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Display contents of CONSULT
Fail-safe
Cancellation
B2190: NATS ANTENNA AMP
Inhibit engine cranking
Erase DTC
B2191: DIFFERENCE OF KEY
Inhibit engine cranking
Erase DTC
B2192: ID DISCORD BCM-ECM
Inhibit engine cranking
Erase DTC
B2193: CHAIN OF BCM-ECM
Inhibit engine cranking
Erase DTC
B2195: ANTI SCANNING
Inhibit engine cranking
Ignition switch ON
→
OFF
B2560: STARTER CONT RELAY
Inhibit engine cranking
500 ms after the following CAN signal communication status be-
comes consistent
• Starter control relay signal
• Starter relay status signal
B2608: STARTER RELAY
Inhibit engine cranking
500 ms after the following signal communication status becomes
consistent
• Starter motor relay control signal
• Starter relay status signal (CAN)
B260A: IGNITION RELAY
Inhibit engine cranking
500 ms after the following conditions are fulfilled
• IGN relay (IPDM E/R) control signal: OFF (Battery voltage)
• Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
• Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
B260F: ENG STATE SIG LOST
Maintains the power supply
position attained at the time
of DTC detection
When any of the following conditions are fulfilled
• Power position changes to ACC
• Receives engine status signal (CAN)
B2617: STARTER RELAY CIRC
Inhibit engine cranking
1 second after the starter motor relay control inside BCM becomes
normal
B2618: BCM
Inhibit engine cranking
1 second after the ignition relay (IPDM E/R) control inside BCM be-
comes normal
B261E: VEHICLE TYPE
Inhibit engine cranking
BCM initialization
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст