Nissan Murano. Manual — part 1247
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-85
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
Description
INFOID:0000000009722813
IPDM E/R confirms the shift position with the following signals.
• Transmission range switch
• Shift position signal from BCM (CAN)
DTC Logic
INFOID:0000000009722814
DTC DETECTION LOGIC
NOTE:
If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions and wait for at least 1 second.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009722815
1.
CHECK DTC WITH BCM
Check “Self diagnostic result” with CONSULT. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK TRANSMISSION RANGE SWITCH INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
.
NO
>> GO TO 3.
3.
CHECK TRANSMISSION RANGE SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector and IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and TCM harness connector.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210F
INTER LOCK/PNP SW
ON
IPDM E/R detects a mismatch between the sig-
nals below for 1 second or more.
• Transmission range switch input signal
• Shift position signal from BCM (CAN)
• Harness or connectors
(Transmission range switch circuit
is open or shorted)
• Transmission range switch
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E10
30
Ground
Selector lever
P or N
Battery voltage
Other than above
0
SEC-86
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
NO
>> Repair or replace harness or connector.
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
E10
72
F23
20
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
72
Not existed
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-87
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
Description
INFOID:0000000009722816
IPDM E/R confirms the shift position with the following signals.
• Transmission range switch
• Shift position signal from BCM (CAN)
DTC Logic
INFOID:0000000009722817
DTC DETECTION LOGIC
NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn the ignition switch ON under the following conditions and wait for at least 1 second.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009722818
1.
CHECK DTC WITH TCM
Check “Self diagnostic result” with CONSULT. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK TRANSMISSION RANGE SWITCH INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
.
NO
>> GO TO 3.
3.
CHECK TRANSMISSION RANGE SWITCH CIRCUIT
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2110
INTER LOCK/PNP
SW
IPDM E/R detects mismatch between the signals
below for 1 second or more.
• Transmission range switch input signal
• Shift position signal from BCM (CAN)
• Harness or connectors
(Transmission range switch circuit is
open or shorted)
• Transmission range switch
• IPDM E/R
• BCM
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E10
30
Ground
Selector lever
P or N
Battery voltage
Other than above
0
SEC-88
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect TCM connector and IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and TCM harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
NO
>> Repair or replace harness or connector.
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
E10
72
F23
20
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
72
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст