Nissan Murano. Manual — part 1221
REAR SEAT
SE-107
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REAR SEAT
Exploded View
INFOID:0000000009718772
REAR SEAT (LH SIDE)
1.
Headrest (LH)
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback trim
5.
Seatback pad
6.
Reclining device inner cover (out-
side)
7.
Reclining device inner cover (inside) 8.
Seat cushion trim
9.
Seat cushion hinge cover
10. Seat cushion link cover
11.
Seat cushion pad and frame
12. Seat cushion link bush
13. Reclining device outer cover
14. Reclining cover
15. Rear seat harness (LH)
JMJIA1466GB
SE-108
< REMOVAL AND INSTALLATION >
REAR SEAT
REAR SEAT (RH SIDE)
16. Reclining device assembly
17. Seatback control cable
18. Seatback control lever escutcheon
19. Seatback frame
20. Seatback board
21. Seatback board clip
22. Seatback silencer
Refer to
for symbols in the figure.
1.
Headrest (RH)
2.
Headrest (center)
3.
Headrest holder (locked)
4.
Headrest holder (free)
5.
Seatback trim
6.
Seatback pad
7.
Armrest inner cover
8.
Cup holder
9.
Armrest
10. Armrest bush
11.
Armrest outer cover
12. Seat cushion trim
13. Seat cushion hinge cover
14. Seat cushion link cover
15. Seat cushion pad and frame
JMJIA1465GB
REAR SEAT
SE-109
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Removal and Installation
INFOID:0000000009718773
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
REMOVAL
1.
Remove the seat mounting bolts and nuts.
a.
Pull up the luggage floor finisher front (1).
b.
Remove the seat mounting bolt (A) and nut (B).
2.
Disconnect the rear seat harness connector (A) and heater unit harness connector (B). (Power return seat
and heater seat model only)
a.
LH side
b.
RH side
3.
Remove the reclining cover.
16. Seat cushion link bush
17. Reclining device inner cover (out-
side)
18. Reclining device inner cover (inside)
19. Reclining device assembly
20. Reclining device outer cover
21. Reclining cover
22. Rear seat harness (RH)
23. Seatback board
24. Seatback board clip
25. Seatback frame
26. Dynamic dumper
27. Seatback control lever escutcheon
28. Seatback control cable
29. Seatback silencer
Refer to
for symbols in the figure.
JMJIA1476ZZ
JMJIA1477ZZ
JMJIA1478ZZ
SE-110
< REMOVAL AND INSTALLATION >
REAR SEAT
4.
Remove the seatback control cable (1) from reclining device
assembly and seat mounting bolt (A).
5.
Remove the seat cushion hinge cover.
1.
Insert a finger from lower side of seat cushion hinge cover
and disengage pawl while pressing it upward, as shown in
the figure.
2.
Slide cushion hinge cover to the under to remove.
CAUTION:
Remove the pawl more carefully.
If pawl was damaged, the cover is broken by case.
6.
Remove the rear seat mounting bolts (A).
JMJIA1479ZZ
: Pawl
JMJIA8278ZZ
: Pawl
JMJIA8279ZZ
JMJIA1480ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст