Nissan Murano. Manual — part 616
EM-38
< REMOVAL AND INSTALLATION >
EXHAUST MANIFOLD AND THREE WAY CATALYST
EXHAUST MANIFOLD AND THREE WAY CATALYST
Exploded View
INFOID:0000000009717971
Removal and Installation
INFOID:0000000009717972
REMOVAL
WARNING:
1.
Gasket
2.
Exhaust manifold (bank 1)
3.
Exhaust manifold cover (bank 1)
4.
Air fuel ratio sensor 1 (bank 1)
5.
Ring gasket
6.
Three way catalyst (bank 1)
7.
Three way catalyst support (bank 1)
8.
Heated oxygen sensor 2 (bank 1)
9.
Three way catalyst (bank 2)
10. Three way catalyst support (bank 2)
11. Heated oxygen sensor 2 (bank 2)
12.
Ring gasket
13. Exhaust manifold (bank 2)
14. Exhaust manifold cover (bank 2)
15.
Air fuel ratio sensor 1 (bank 2)
A.
To oil pan (upper)
B.
Upper mark
C.
Stud bolt and flange bolt type
(bank 2)
D.
Flange bolt type (bank 2)
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JPBIA2710GB
EXHAUST MANIFOLD AND THREE WAY CATALYST
EM-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Perform the work when the exhaust and cooling system have completely cooled down.
1.
Remove following parts:
• Radiator core support covers (RH and LH), air duct (inlet), air cleaner case (upper) with mass air flow
sensor and air duct assembly: Refer to
.
• Engine cover: Refer to
• Front wiper arm: Refer to
• Extension cowl top: Refer to
.
2.
Remove exhaust front tube. Refer to
3.
Disconnect harness connector and remove air fuel ratio sensor
1 on both banks with the heated oxygen sensor wrench [SST:
KV10117100 (J-3647-A)] (B).
• Put marks to identify installation positions of each air fuel ratio
sensor 1.
CAUTION:
• Be careful not to damage air fuel ratio sensor 1.
• Discard any air fuel ratio sensor 1 which has been
dropped onto a hard surface such as a concrete floor.
Replace with a new sensor.
NOTE:
Figure is shown as an example of bank 2 (A).
4.
Disconnect harness connector and remove heated oxygen sen-
sor 2 on both banks with the heated oxygen sensor wrench
[SST: KV10114400 (J-38365)] (B).
• Put marks to identify installation positions of each heated oxy-
gen sensor 2.
CAUTION:
• Be careful not to damage heated oxygen sensor 2.
• Discard any heated oxygen sensor 2 which has been
dropped onto a hard surface such as a concrete floor.
Replace with a new sensor.
5.
Remove exhaust manifold covers (bank 1 and bank 2).
6.
Remove three way catalyst support mounting bolts (bank 1 and bank 2).
7.
Remove three way catalysts by loosening bolts first and then removing nuts. (Stud bolt and flange bolt
type)
CAUTION:
Handle carefully to avoid any shock to three way catalyst.
JPBIA1781ZZ
A
: Bank 2
C
: Bank 1
JPBIA1724ZZ
EM-40
< REMOVAL AND INSTALLATION >
EXHAUST MANIFOLD AND THREE WAY CATALYST
8.
Loosen mounting nuts in the reverse order as shown in the fig-
ure to remove exhaust manifolds (bank 1 and bank 2).
NOTE:
Disregard No. 7 and 8 when loosing.
9.
Remove gaskets.
CAUTION:
Cover engine openings to avoid entry of foreign materials.
INSTALLATION
Note the following, and install in the reverse order of removal.
Exhaust Manifold Gasket
Install in the direction indicated in the figure.
Exhaust Manifold
• If stud bolts were removed, install them and tighten to the torque specified below.
A
: Bank 1
B
: Bank 2
: Engine front
JPBIA1633ZZ
A
: Bank 1
B
: Triangle press
C
: Bank 2
: Engine front
PBIC4954E
: 15.4 N·m (1.6 kg-m, 11 ft-lb)
EXHAUST MANIFOLD AND THREE WAY CATALYST
EM-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Tighten mounting nuts in numerical order as shown in the figure.
NOTE:
No. 7 and 8 mean double tightening of nuts No. 1 and 2.
Three Way Catalyst (bank 2) Flange Bolt Type
1.
Temporarily tighten upper side bolts (B) and lower side bolt (A)
shown in the figure.
2.
Tighten the upper side bolts (B) shown in the figure. (specified
torque)
3.
Tighten all the lower side bolts [the other four except (B)]. (spec-
ified torque)
Three Way Catalyst Supports
1.
Temporarily tighten three way catalyst support mounting bolts.
2.
Tighten three way catalyst support mounting bolts to oil pan (upper).
3.
Tighten three way catalyst support mounting bolts to three way catalyst.
Air Fuel Ratio Sensor 1 and Heated Oxygen Sensor 2
• Install air fuel ratio sensor 1 and heated oxygen sensor 2 in the original position.
• Install referring the following if the installation positions cannot be
identified.
CAUTION:
• Before installing a new air fuel ratio sensor and a new heated
oxygen sensor, clean exhaust system threads using oxygen
sensor thread cleaner (commercial service tool: J-43897-18 or
J-43897-12) and apply anti-seize lubricant (commercial ser-
vice tool).
• Never over torque air fuel ratio sensor and heated oxygen sensor. Doing so may cause damage to air
fuel ratio sensor and heated oxygen sensor, resulting in “MIL” coming on.
A
: Bank 1
B
: Bank 2
: Engine front
JPBIA1633ZZ
: Engine front
JPBIA2709ZZ
Glass tube color
Air fuel ratio sensor 1
: Black
Heated oxygen sensor 2
: White
PBIC2652E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст