Nissan Murano. Manual — part 457
DRIVE PINION
DLN-67
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY20A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
8.
Put out the circumference of pinion sleeve oil seal from back
side of pinion sleeve with punch to remove pinion sleeve oil
seal.
CAUTION:
When removing oil seal, never damage the pinion sleeve by
scooping it out with a tool.
9.
Remove pinion rear bearing inner race.
10. Remove the pinion rear bearing outer race with the puller (A)
[SST: KV381054S0 (J-34286)].
11. Remove the pinion front bearing outer race with the puller (A)
[SST: KV381054S0 (J-34286)].
12. Remove the collapsible spacer from the drive pinion.
13. Using the replacer (A) (commercial service tool), press the pin-
ion front bearing inner race out of the drive pinion.
Assembly
INFOID:0000000009718154
1.
Select the pinion sleeve shim. Refer to
JSDIA2345ZZ
JPDIE0026ZZ
JPDIE0027ZZ
JPDIE0028ZZ
DLN-68
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY20A]
DRIVE PINION
2.
Install the pinion rear bearing outer race with the drift (A) [SST:
KV38100300 (J-25523)].
3.
Install the pinion front bearing outer race with the drifts.
4.
Install the pinion front bearing inner race to drive pinion with the
drift (A) [SST: ST30901000 (J-26010-01)].
Apply gear oil to the pinion front bearing.
CAUTION:
• Never reuse pinion front bearing.
5.
Install a collapsible spacer to the drive pinion.
CAUTION:
Never reuse collapsible spacer.
6.
Install the pinion rear bearing inner race to pinion sleeve.
Apply gear oil to the pinion rear bearing.
CAUTION:
• Never reuse pinion rear bearing.
7.
Install pinion sleeve oil seal to pinion sleeve with the drift (A)
[SST: ST33400001 (J-26082)].
Apply multi-purpose grease onto oil seal lips, and gear oil onto
the circumference.
CAUTION:
• Never reuse oil seal.
• Use the drift with larger diameter than outer diameter of
oil seal.
8.
Install companion flange to pinion sleeve assembly with the drift
(A) [SST: ST33200000 (J-26082)].
9.
Apply anti-corrosive oil to the thread and seat of the lock nut,
and adjust the pinion lock nut tightening torque and pinion bear-
ing preload torque, using a preload gauge.
JPDIE0043ZZ
A
: Drift [SST: ST33400001 (J-26082)]
B
: Drift [SST: ST30901000 (J–26010-01)]
JPDIE0044ZZ
JPDIE0045ZZ
JPDIE0046ZZ
Standard
Drive pinion lock nut
tighten torque
: 128 – 294 N·m (13 – 29 kg-m,
95 – 216 ft-lb)
JPDIE0047ZZ
DRIVE PINION
DLN-69
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY20A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
CAUTION:
• Never reuse lock nut.
• If specified preload torque is exceeded, replace the collapsible spacer and tighten again. Never
loosen the pinion lock nut for further preload torque adjustment.
10. Apply multi-purpose grease lightly and evenly onto an O-ring, and install it to the pinion sleeve.
CAUTION:
• Never reuse O-ring.
• When installing O-ring, never use a tool.
• Never damage the pinion sleeve.
11. Assemble the selected pinion sleeve shim.
12. Install the pinion sleeve assembly, and apply anti-corrosive oil onto thread and seats on the mounting
bolts. Tighten to the specified torque. Refer to
13. Check backlash, tooth contact, total preload and companion flange runout. Refer to
.
CAUTION:
Measure the total preload without the adapter case oil seal.
Adjustment
INFOID:0000000009718155
BACKLASH
1.
Install a bolt to the companion flange.
2.
Fit a dial indicator onto the bolt.
3.
Measure the circumference backlash of the companion flange,
and Check that it satisfies the standard below.
• If measured value is out of the specification, disassemble it to
check and adjust each part.
TOOTH CONTACT
1.
Remove the pinion sleeve assembly. Refer to
.
2.
Apply red lead to the drive gear.
CAUTION:
Apply red lead to both the faces of 3 to 4 gears at 4 loca-
tions evenly spaced on the drive gear.
3.
Install the pinion sleeve shims and pinion sleeve assembly.
Refer to
.
4.
Remove the plug on the upper side of the transfer case.
When installing plug, apply sealant on screw part, and tighten it
at the specified torque. Refer to
Use Genuine Silicone RTV or equivalent. Refer to
"Recommended Chemical Products and Sealants"
.
Standard
Drive pinion bearing preload
: Refer to
Backlash
: Refer to
SDIA1801E
SDIA1524E
DLN-70
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY20A]
DRIVE PINION
5.
Rotate the companion flange back and forth several times, and
check the drive pinion gear to drive gear tooth contact by view-
ing from the plug hole.
6.
If tooth contact is poorly adjusted, adjust pinion height (dimen-
sion X) in the following manner.
For selecting adjusting shims, refer to the latest parts informa-
tion.
SDIA1802E
SDIA0520E
SDIA0517E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст