Nissan Murano. Manual — part 362
DIAGNOSIS SYSTEM (BCM)
DLK-59
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
UNLK SEN -DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
PUSH SW -IPDM
Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY1 -F/B
Indicates [ON/OFF] condition of ignition relay 1.
DETE SW -IPDM
Indicates [ON/OFF] condition of P position.
SFT PN -IPDM
Indicates [ON/OFF] condition of P or N position.
SFT P -MET
Indicates [ON/OFF] condition of P position.
SFT N -MET
Indicates [ON/OFF] condition of N position.
ENGINE STATE
Indicates [STOP/START/CRANK/RUN] condition of engine states.
S/L LOCK-IPDM
Indicates [ON/OFF] condition of steering lock unit (LOCK).
NOTE:
For models without steering lock unit this item is not displayed.
S/L UNLK-IPDM
Indicates [ON/OFF] condition of steering lock unit (UNLOCK).
NOTE:
For models without steering lock unit this item is not displayed.
S/L RELAY-REQ
Indicates [ON/OFF] condition of steering lock relay.
NOTE:
For models without steering lock unit this item is not displayed.
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h].
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].
DOOR STAT-DR
Indicates [LOCK/READY/UNLOCK] condition of driver side door status.
DOOR STAT-AS
Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.
ID OK FLAG
Indicates [SET/RESET] condition of key ID.
PRMT ENG STRT
Indicates [SET/RESET] condition of engine start possibility.
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored.
RKE-PANIC
Indicates [ON/OFF] condition of PANIC button of Intelligent Key.
RKE-P/W OPEN
Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.
RKE-MODE CHG
Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the
numerical value start changing.
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored.
Monitor Item
Condition
Test item
Description
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.
PW REMOTO DOWN SET
This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT screen is touched.
DLK-60
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
TRUNK
TRUNK : CONSULT Function (BCM - TRUNK)
INFOID:0000000009718914
BCM CONSULT FUNCTION
CONSULT performs the following functions via CAN communication with BCM.
INSIDE BUZZER
This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT screen is touched.
• Key warning chime sounds when “KEY WARN” on CONSULT screen is touched.
• P position warning chime sounds when “P RNG WARN” on CONSULT screen is touched.
• ACC warning chime sounds when “ACC WARN” on CONSULT screen is touched.
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer will be activated after “ON” on CONSULT screen is touched.
INDICATOR
This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “KEY ON” on CONSULT screen is touched.
• “KEY” Warning lamp flashes when “KEY IND” on CONSULT screen is touched.
INT LAMP
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.
LCD
This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT screen is touched.
• Engine start information displays when “BP I” on CONSULT screen is touched.
• Key ID warning displays when “ID NG” on CONSULT screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT screen is touched.
NOTE:
For models without steering lock unit, “ROTAT” is displayed, but cannot be tested.
• P position warning displays when “SFT P” on CONSULT screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT screen is touched.
• Take away through window warning displays when “NO KY” on CONSULT screen is touched.
• Take away warning display when “OUTKEY” on CONSULT screen is touched.
• OFF position warning display when “LK WN” on CONSULT screen is touched.
TRUNK/GLASS HATCH
This test is able to check back door opener actuator open operation.
This actuator opens when “ON” on CONSULT screen is touched.
FLASHER
This test is able to check hazard warning lamp operation.
The hazard warning lamps will be activated after “ON” on CONSULT screen is touched.
HORN
This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT screen is touched.
IGN CONT2
This test is able to check ignition relay operation.
The ignition relay will be activated after “ON” on CONSULT screen is touched.
P RANGE
This test is able to check CVT shift selector power supply
CVT shift selector power is supplied when “ON” on CONSULT screen is touched.
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched.
LOCK INDICATOR
NOTE:
This item is displayed, but cannot be tested.
ACC INDICATOR
This test is able to check indicator in push-ignition switch operation.
Indicator in push-button ignition switch illuminates when “ON” on CONSULT screen is touched.
IGNITION ON IND
This test is able to check indicator in push-ignition switch operation.
Indicator in push-button ignition switch illuminates when “ON” on CONSULT screen is touched.
KEY SLOT ILLUMI
This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT screen is touched.
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be tested.
AUTOMATIC SLIDING DOOR
NOTE:
This item is displayed, but cannot be tested.
Test item
Description
DIAGNOSIS SYSTEM (BCM)
DLK-61
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
*: With back door opener system
ACTIVE TEST
Diagnosis mode
Function Description
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitor Item
Contents
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
UNLK SEN -DR
NOTE:
This item is displayed, but cannot be monitored.
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter.
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored.
TR CANCEL SW
NOTE:
This item is displayed, but cannot be monitored.
TR/BD OPEN SW
Indicates [ON/OFF] condition of back door opener switch.
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored.
RKE-TR/BD*
NOTE:
This item is displayed, but cannot be monitored.
Test item
Description
TRUNK/GLASS HATCH
This test is able to check back door opener actuator open operation.
This actuator opens when “”
DLK-62
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)
DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)
CONSULT Function (AUTOMATIC BACK DOOR CONTROL UNIT)
INFOID:0000000009718915
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with automatic back door control unit.
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
SELF-DIAG RESULT
Diagnosis mode
Function Description
SELF-DIAG RESULTS
Displays the diagnosis results judged by automatic back door control unit.
CAN DIAG SUPPORT MNTR
Monitors the reception status of CAN communication viewed from automatic back door
control unit.
DATA MONITOR
The automatic back door control unit input/output signals are displayed.
ECU IDENTIFICATION
The automatic back door control unit part number is displayed.
Monitor Item
Unit
Description
VHCL SPEED MTR
[km/h]
Display the vehicle speed signal received from combination meter by nu-
merical value.
VHCL SPEED ABS
[km/h]
Display the vehicle speed signal received from ABS actuator and electrical
unit by numerical value [km/h].
MAIN SW
[ON/OFF]
Indicates condition of main switch.
AUTO BD SW
[ON/OFF]
Indicates condition of main switch.
BK DOOR CL SW
[ON/OFF]
Indicates condition of back door close switch.
UNLOCK SEN DR
[ON/OFF]
Indicates condition of unlock sensor (driver).
OPEN SW
[ON/OFF]
Indicates condition of open switch.
CLOSE SW
[ON/OFF]
Indicates condition of close switch.
HALF LATCH SW
[ON/OFF]
Indicates condition of half latch switch.
TOUCH SEN RH
[ON/OFF/OPEN]
Indicates condition of touch sensor RH.
TOUCH SEN LH
[ON/OFF/OPEN]
Indicates condition of touch sensor LH.
P RANGE IND
[ON/OFF]
Indicates condition of P range signal from combination meter.
RKE REQ
[OFF/MOVE/
REV]
Indicates condition of remote keyless entry signal from BCM.
IGN SW
[ON/OFF]
Indicates condition of IGN power supply.
ENCODER A
[LO/HI]
Indicates condition of encoder signal from encoder A.
ENCODER B
[LO/HI]
Indicates condition of encoder signal from encoder B.
BD OPENER SW
[ON/OFF]
Indicates condition of back door opener switch.
UNLOCK SEN BD
[LOCK/
UNLOCK]
Indicates condition of unlock sensor (back door).
DESTINATION
[JPN/NAM]
Indicates specification of destination of the parts.
HAZARD
[ON/OFF]
Indicates specification of hazard warning.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст