Nissan Murano. Manual — part 21
ADP-76
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch. Refer to
POWER SEAT SWITCH GROUND CIRCUIT
ADP-77
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
POWER SEAT SWITCH GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000009720717
1.
CHECK POWER SEAT SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch connector.
3.
Check continuity between power seat switch connector and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Repair or replace harness or connector.
Power seat switch
Ground
Continuity
Connector
Terminal
B459
35
Existed
ADP-78
< DTC/CIRCUIT DIAGNOSIS >
TILT &TELESCOPIC SWITCH GROUND CIRCUIT
TILT &TELESCOPIC SWITCH GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000009720718
1.
CHECK TILT & TELESCOPIC SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect tilt & telescopic switch connector.
3.
Check continuity between tilt & telescopic switch and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Repair or replace harness.
Tilt & telescopic switch
Ground
Continuity
Connector
Terminal
M102
1
Existed
FRONT DOOR SWITCH (DRIVER SIDE)
ADP-79
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
FRONT DOOR SWITCH (DRIVER SIDE)
Description
INFOID:0000000009720719
Detects front door (driver side) open/close condition.
Component Function Check
INFOID:0000000009720720
1.
CHECK FUNCTION
1.
Select “DOOR SW-DR” in “Data monitor” mode with CONSULT.
2.
Check the front door switch (driver side) signal under the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
.
Diagnosis Procedure
INFOID:0000000009720721
1.
CHECK FRONT DOOR SWITCH (DRIVER SIDE) SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door switch (driver side) connector.
3.
Check signal between BCM connector and ground with oscilloscope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FRONT DOOR SWITCH (DRIVER SIDE) CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM connector and front door switch (driver side) connector.
3.
Check continuity between BCM connector and ground.
Is the inspection result normal?
Monitor item
Condition
Status
DOOR SW-DR
Front door switch
(driver side)
Open
ON
Close
OFF
(+)
(–)
Signal
(Reference value)
Front door switch(driver side)
Connector
Terminals
B34
2
Ground
JPMIA0011GB
BCM
Front door switch(driver side)
Continuity
Connector
Terminal
Connector
Terminal
M123
150
B34 2
Existed
BCM
Ground
Continuity
Connector
Terminal
M123
150
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст