Nissan Murano. Manual — part 1338
ST-46
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE
Exploded View
INFOID:0000000009721490
REMOVAL
2WD models
AWD models
DISASSEMBLY
JSGIA0606GB
1.
Steering gear assembly
2.
Cotter pin
: Vehicle front
Refer to
for symbols in the figure.
JSGIA0607GB
1.
Steering gear assembly
2.
Cotter pin
: Vehicle front
Refer to
for symbols in the figure.
STEERING GEAR AND LINKAGE
ST-47
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
2WD models
JSGIA0571GB
1.
Low pressure piping
2.
Rear cover cap
3.
Gear-sub assembly
4.
Power steering solenoid valve
5.
O-ring
6.
Adjusting screw
7.
Spring
8.
Retainer
9.
Outer socket
10. Boot clamp
11.
Boot
12. Inner socket
13. Boot clamp (stainless wire)
14. Cylinder tube
15. Gear housing assembly
16. Rack oil seal
17. Rack assembly
18. Rack Teflon ring
19. O-ring
20. End cover assembly
: Apply power steering fluid.
: Apply Genuine Medium Strength Thread Locking Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Prod-
.
: Apply Genuine High Performance Thread Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and
: Apply multi-purpose grease.
Refer to
ST-48
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
STEERING GEAR AND LINKAGE
AWD models
Removal and Installation
INFOID:0000000009721491
REMOVAL
1.
Set the vehicle to the straight-ahead position.
2.
Remove front road wheel and tires.
3.
Remove splash guards (RH and LH). Refer to
EXT-26, "FENDER PROTECTOR : Exploded View"
.
4.
Remove engine under cover. Refer to
.
5.
Remove exhaust front tube. Refer to
6.
Separate the rear propeller shaft (front side). Refer to
(AWD models).
7.
Remove heat insulator from front floor.
JSGIA0572GB
1.
Low pressure piping
2.
Rear cover cap
3.
Gear-sub assembly
4.
Power steering solenoid valve
5.
O-ring
6.
Adjusting screw
7.
Spring
8.
Retainer
9.
Outer socket
10. Boot clamp
11.
Boot
12. Inner socket
13. Boot clamp (stainless wire)
14. Cylinder tube
15. Gear housing assembly
16. Rack oil seal
17. Rack assembly
18. Rack Teflon ring
19. O-ring
20. End cover assembly
: Apply power steering fluid.
: Apply Genuine Medium Strength Thread Locking Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Prod-
.
: Apply Genuine High Performance Thread Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and
.
: Apply multi-purpose grease.
Refer to
for symbols not described on the above.
STEERING GEAR AND LINKAGE
ST-49
< REMOVAL AND INSTALLATION >
[WITH HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
8.
Remove cotter pin (1), and then loosen the nuts.
9.
Remove steering outer socket (2) from steering knuckle (3) so
as not to damage ball joint boot (4) using a ball joint remover
(commercial service tool).
CAUTION:
Temporarily tighten the nut to prevent damage to threads
and to prevent the ball joint remover from suddenly coming
off.
10. Remove high pressure piping and low pressure hose of hydrau-
lic piping, and then drain power steering fluid.
11. Remove steering hydraulic piping bracket from front steering
gear assembly.
12. Remove power steering solenoid valve harness connector (1)
and harness clip.
13. Remove lower joint fixing bolt (steering gear side).
14. Separate the lower shaft from the steering gear assembly by sliding the slide shaft.
CAUTION:
• Spiral cable may be cut if steering wheel turns while separating steering column assembly and
steering gear assembly. Be sure to secure steering wheel using string to avoid turning.
• When removing lower shaft, never insert a tool, such as a screwdriver, into the yoke groove to
pull out the lower shaft. In case of the violation of the above, replace lower shaft with a new one.
15. Remove the stabilizer assembly. Refer to
16. Support front suspension member with a suitable jack.
17. Remove engine mounting insulator (rear) mounting bolt (lower side). Refer to
(2WD models),
(AWD models).
18. Remove engine mounting insulator (LH). Refer to
(AWD models).
19. Remove the mounting bolts and nuts of steering gear assembly.
20. Remove member stay, front suspension member fixing bolts and nuts. Refer to
.
21. Lower the suitable jack for the front suspension member to the steering gear assembly can be removed.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column assembly and steer-
ing gear assembly. Be sure to secure steering wheel using string to avoid turning.
JSGIA0320ZZ
: Bolt
JSGIA0321ZZ
JSGIA0322ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст