Nissan Murano. Manual — part 634
EM-110
< UNIT DISASSEMBLY AND ASSEMBLY >
OIL SEAL
4.
Use a seal cutter (SST) to cut away liquid gasket and remove
rear oil seal retainer.
CAUTION:
Be careful not to damage mating surfaces.
NOTE:
Regard both rear oil seal and retainer an assembly.
INSTALLATION
1.
Remove old liquid gasket on mating surfaces of cylinder block and oil pan (upper) using scraper.
2.
Apply new engine oil to both oil seal lip and dust seal lip of new oil seal retainer.
3.
Apply a continuous bead of liquid gasket with the tube presser
(commercial service tool) to rear oil seal retainer as shown in the
figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and Sealants"
.
CAUTION:
Attaching should be done within 5 minutes after coating.
4.
Install rear oil seal retainer to cylinder block. Refer to
.
• Check the garter spring is in position and seal lips not inverted.
5.
Install in the reverse order of removal after this step.
SEM830E
a
:
φ
2.0 - 3.0 mm (0.08 - 0.12 in)
JPBIA0542ZZ
CYLINDER HEAD
EM-111
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CYLINDER HEAD
Exploded View
INFOID:0000000009718002
REMOVAL
DISASSEMBLY
1.
Oil level gauge
2.
Cylinder head (bank 2)
3.
Cylinder head bolt
4.
Cylinder head (bank 1)
5.
Cylinder head gasket (bank 1)
6.
Cylinder head gasket (bank 2)
A.
Comply with the installation procedure
when tightening. Refer to
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Should be lubricated with oil.
JPBIA1748ZZ
EM-112
< UNIT DISASSEMBLY AND ASSEMBLY >
CYLINDER HEAD
Removal and Installation
INFOID:0000000009718003
REMOVAL
1.
Remove the following parts:
• Oil level gauge
• Intake manifold collector: Refer to
.
• Rocker cover: Refer to
• Fuel tube and fuel injector assembly: Refer to
• Intake manifold: Refer to
• Exhaust manifold: Refer to
• Water inlet and thermostat assembly: Refer to
.
• Water outlet, water connector, water bypass pipe, and heater pipe: Refer to
• Timing chain and rear timing chain case: Refer to
and
.
• Camshaft: Refer to
.
1.
Valve lifter
2.
Valve collet
3.
Valve spring retainer
4.
Valve spring
5.
Valve oil seal
6.
Valve spring seat
7.
Valve guide (EXH)
8.
Spark plug
9.
Spark plug tube
10. Cylinder head (bank 1)
11.
Valve seat (EXH)
12. Valve (EXH)
13. Valve (INT)
14. Valve seat (INT)
15. Valve guide (INT)
16. Cylinder head (bank 2)
: Apply genuine high strength thread locking sealant or equivalent.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Should be lubricated with oil.
: Sealing point
: Select with proper thickness.
JPBIA1728GB
CYLINDER HEAD
EM-113
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Remove cylinder head bolts in the reverse order as shown in the
figure with cylinder head bolt wrench (commercial service tool)
and power tool to remove cylinder heads (bank 1 and bank 2).
3.
Remove cylinder head gaskets.
INSTALLATION
1.
Install new cylinder head gaskets.
2.
Turn crankshaft until No. 1 piston is set at TDC.
• Crankshaft key (1) should line up with the bank 1 cylinder cen-
ter line as shown in the figure.
A
: Bank 1
B
: Bank 2
: Engine front
JPBIA0172ZZ
: Bank 1 side
JPBIA1752ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст