Nissan Murano. Manual — part 365
B2409 HALF LATCH SWITCH
DLK-71
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between automatic back door control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control unit. Refer to
DLK-368, "Removal and Installation"
.
NO
>> Repair or replace harness.
4.
CHECK HALF LATCH SWITCH GROUND CIRCUIT
Check continuity between back door lock assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace back door lock assembly ground circuit.
5.
CHECK HALF LATCH SWITCH
DLK-71, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace back door lock assembly. Refer to
DLK-365, "Removal and Installation"
.
6.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000009718936
COMPONENT INSPECTION
1.
CHECK HALF LATCH SWITCH
Check back door lock assembly (half latch switch).
Is the inspection result normal?
YES
>> Half latch switch is OK.
NO
>> Replace back door lock assembly. Refer to
DLK-351, "DOOR LOCK : Removal and Installation"
Automatic back door control unit
Back door lock assembly
Continuity
Connector
Terminal
Connector
Terminal
B8
8
D179
6
Existed
Automatic back door control unit
Ground
Continuity
Connector
Terminal
B8
8
Not existed
Back door lock assembly
Ground
Continuity
Connector
Terminal
D179
8
Existed
Terminal
Condition
Continuity
Back door lock assembly (half latch switch)
6
8
Back door lock
Open
Existed
Fully closed/Half latch
Not existed
DLK-72
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2416 TOUCH SENSOR RH
B2416 TOUCH SENSOR RH
Description
INFOID:0000000009718937
The touch sensor RH is installed on the right edge of the back door, and it detects any trapped foreign material
in the back door during the auto close operation and at the closure operation.
DTC Logic
INFOID:0000000009718938
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009718939
1.
CHECK TOUCH SENSOR RH SIGNAL
Check touch sensor RH (“TOUCH SEN RH”) in Data Monitor mode.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 2.
2.
CHECK AUTOMATIC BACK DOOR CONTROL UNIT OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect touch sensor RH connector.
3.
Check voltage between touch sensor RH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK TOUCH SENSOR RH CIRCUIT
1.
Disconnect automatic back door control unit connector.
2.
Check continuity between automatic back door control unit harness connector and touch sensor RH har-
ness connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2416
TOUCH SENSOR
RH
When the automatic back door control unit detects
the open circuit of the touch sensor RH
• Touch sensor RH
• Harness or connectors
(Touch sensor RH circuit is short-
ed)
• Automatic back door control unit
Monitor item
Condition
Status
TOUCH SEN RH
Touch sensor RH
Other than below
OFF
Detect obstruction
ON
(+)
(–)
Voltage (V)
(Approx.)
Touch sensor RH
Connector
Terminal
D164
1
Ground
6
B2416 TOUCH SENSOR RH
DLK-73
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between automatic back door control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic back door control unit. Refer to
DLK-368, "Removal and Installation"
.
NO
>> Repair or replace harness.
4.
CHECK TOUCH SENSOR RH GROUND CIRCUIT
Check continuity between automatic back door control unit harness connector and touch sensor RH harness
connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK TOUCH SENSOR RH
DLK-73, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace touch sensor RH. Refer to
DLK-354, "TOUCH SENSOR : Removal and Installation"
6.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000009718940
1.
CHECK TOUCH SENSOR RH
Check touch sensor RH.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace touch sensor RH. Refer to
DLK-354, "TOUCH SENSOR : Removal and Installation"
Automatic back door control unit
Touch sensor RH
Continuity
Connector
Terminal
Connector
Terminal
B8
16
D164
1
Existed
Automatic back door control unit
Ground
Continuity
Connector
Terminal
B8
16
Not existed
Automatic back door control unit
Touch sensor RH
Continuity
Connector
Terminal
Connector
Terminal
B8
15
D164
2
Existed
Terminal
Condition
Resistance
(Approx.)
Touch sensor RH
1
2
Touch sensor RH
Detect obstruction
120
Ω
or less
Other than above
1 k
Ω
±
10%
DLK-74
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2417 TOUCH SENSOR LH
B2417 TOUCH SENSOR LH
Description
INFOID:0000000009718941
The touch sensor LH is installed on the light edge of the back door, and it detects any trapped foreign material
in the back door during the auto close operation and at the closure operation.
DTC Logic
INFOID:0000000009718942
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009718943
1.
CHECK TOUCH SENSOR RH SIGNAL
Check touch sensor LH (“TOUCH SEN LH”) in Data Monitor mode.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 2.
2.
CHECK AUTOMATIC BACK DOOR CONTROL UNIT OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect touch sensor LH connector.
3.
Check voltage between touch sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK TOUCH SENSOR LH CIRCUIT
1.
Disconnect automatic back door control unit.
2.
Check continuity between automatic back door control unit harness connector and touch sensor LH har-
ness connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2417
TOUCH SENSOR LH
When the automatic back door control unit detects
the open circuit of the touch sensor LH.
• Touch sensor LH
• Harness or connectors
(Touch sensor LH circuit is open)
• Automatic back door control unit
Monitor item
Condition
Status
TOUCH SEN LH
Touch sensor LH
Other than below
OFF
Detect obstruction
ON
(+)
(–)
Voltage (V)
(Approx.)
Touch sensor LH
Connector
Terminal
D165
1
Ground
6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст