Nissan Murano. Manual — part 1049
MWI-76
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
Fail-Safe
INFOID:0000000009721304
FAIL-SAFE
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.
JRNWC8911GB
MWI
COMBINATION METER
MWI-77
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DTC Index
INFOID:0000000009721305
Function
Specifications
Speedometer
Reset to zero by suspending communication.
Tachometer
Engine coolant temperature gauge
Illumination control
When suspending communication, changes to nighttime
mode.
Information display
Door open warning
The display turns off by suspending communication.
Parking brake release warning
Low tire pressure warning
Fuel filler cap warning
Instantaneous fuel warning
• When reception time of an abnormal signal is 2 seconds or
less, the last received datum is used for calculation to indi-
cate the result.
• When reception time of an abnormal signal is more than two
seconds, the last result calculated during normal condition
is indicated.
Average fuel consumption
Average vehicle speed
Travel distance
Buzzer
The buzzer turns off by suspending communication.
Warning lamp/indicator
lamp
ABS warning lamp
The lamp turns on by suspending communication.
Brake warning lamp
AWD warning lamp
Malfunction indicator lamp
Low tire pressure warning lamp
The lamp turns ON after flashing for 1 minute.
High beam indicator lamp
The lamp turns off by suspending communication.
Turn signal indicator lamp
Light indicator lamp
Oil pressure warning lamp
CRUISE indicator lamp
O/D OFF indicator lamp
VDC warning lamp
VDC OFF indicator lamp
AWD LOCK indicator lamp
Key warning lamp
Blind Spot Intervention ON indicator
BSW/Blind Spot Intervention warning
lamp
Lane departure warning lamp
LDW ON indicator lamp
Display contents of CONSULT
Diagnostic item is detected when ...
Refer to
CAN COMM CIRCUIT
[U1000]
When combination meter is not transmitting or receiving CAN communication signal
for 2 seconds or more.
CONTROL UNIT (CAN)
[U1010]
When detecting error during the initial diagnosis of the CAN controller of combina-
tion meter.
MWI-78
< ECU DIAGNOSIS INFORMATION >
COMBINATION METER
VEHICLE SPEED
[B2205]
The abnormal vehicle speed signal is input from the ABS actuator and electric unit
(control unit) for 2 seconds or more.
ENGINE SPEED
[B2267]
If ECM continuously transmits abnormal engine speed signals for 2 seconds or
more.
WATER TEMP
[B2268]
If ECM continuously transmits abnormal engine coolant temperature signals for 60
seconds or more.
Display contents of CONSULT
Diagnostic item is detected when ...
Refer to
MWI
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
MWI-79
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)
Reference Value
INFOID:0000000010088708
VALUES ON THE DIAGNOSIS TOOL
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor Item
Condition
Value/Status
MOTOR FAN REQ
Engine idle speed
Changes depending on engine
coolant temperature, air conditioner
operation status, vehicle speed,
etc.
1/2/3/4
AC COMP REQ
Engine running
A/C switch OFF
Off
A/C switch ON
(Compressor is operating)
On
TAIL&CLR REQ
Lighting switch OFF
Off
Lighting switch 1ST, 2ND, HI or AUTO (Light is illuminated)
On
HL LO REQ
Lighting switch OFF
Off
Lighting switch 2ND HI or AUTO (Light is illuminated)
On
HL HI REQ
Lighting switch OFF
Off
Lighting switch HI
On
FR FOG REQ
Lighting switch 2ND or
AUTO (Light is illuminated)
Front fog lamp switch OFF
Off
• Front fog lamp switch ON
• Daytime running light activated
(Only for Canada)
On
FR WIP REQ
Ignition switch ON
Front wiper switch OFF
Stop
Front wiper switch INT
1LOW
Front wiper switch LO
Low
Front wiper switch HI
Hi
WIP AUTO STOP
Ignition switch ON
Front wiper stop position
STOP P
Any position other than front wiper
stop position
ACT P
WIP PROT
Ignition switch ON
Front wiper operates normally
Off
Front wiper stops at fail-safe opera-
tion
BLOCK
IGN RLY1 -REQ
Ignition switch OFF or ACC
Off
Ignition switch ON
On
IGN RLY
Ignition switch OFF or ACC
Off
Ignition switch ON
On
PUSH SW
Release the push-button ignition switch
Off
Press the push-button ignition switch
On
INTER/NP SW
Ignition switch ON
Selector lever in any position other
than P or N
Off
Selector lever in P or N position
On
ST RLY CONT
Ignition switch ON
Off
At engine cranking
On
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст