Nissan Murano. Manual — part 911
BODY SIDE TRIM
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
a.
Disengage front pillar garnish fixing anchor clips with remover
tool (A).
b.
Cut anchor clip (A) portion using nippers (B).
c.
Remove front pillar garnish while lifting it upward.
d.
Remove clips remaining on body side using a remover tool.
FRONT KICKING PLATE INNER
1.
Disengage the pawls and metal clip from the body panel with
remover tool (A).
2.
Remove front kicking plate inner (1).
FRONT KICKING PLATE OUTER
: Anchor clip
JMJIA4843ZZ
JMJIA4844ZZ
JMJIA6202ZZ
: Pawl
: Metal clip
JMJIA1365ZZ
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
1.
Disengage the pawls from the body panel with remover tool (A).
2.
Remove front kicking plate outer (1).
FRONT BODY SIDE WELT
1.
Remove front kicking plate inner.
2.
Remove center pillar upper garnish.
3.
Remove front body side welt.
REAR BODY SIDE WELT
1.
Remove rear kicking plate inner.
2.
Remove center pillar upper garnish.
3.
Remove rear body side welt.
DASH SIDE FINISHER
1.
Remove front kicking plate inner.
2.
Disengage dash side finisher (1) mounting clip with remover tool
(A).
3.
Remove dash side finisher (1).
REAR KICKING PLATE INNER
1.
Disengage the pawls from the body with remover tool (A).
2.
Remove rear kicking plate inner (1).
REAR KICKING PLATE OUTER
: Pawl
JMJIA1366ZZ
: Clip
JMJIA2448ZZ
: Pawl
JMJIA1368ZZ
BODY SIDE TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
1.
Disengage the pawls from the body side panel with remover tool
(A).
2.
Remove rear kicking plate outer (1).
CENTER PILLAR LOWER GARNISH
1.
Remove front kicking plate inner and rear kicking plate inner.
2.
Insert remover tool (A) between center pillar lower garnish (1)
and body side panel to disengage the metal clips.
3.
Remove anchor bolt cover (2), then remove the anchor bolt
behind the cover.
4.
Remove center pillar lower garnish (1).
CENTER PILLAR UPPER GARNISH
1.
Remove partially front and rear body side welt.
2.
Remove front kicking plate inner and rear kicking plate inner.
3.
Remove center pillar lower garnish.
4.
Remove front seat belt shoulder anchor (2).
5.
Remove the bolt located behind the center pillar upper cap (A).
6.
Pull back center pillar upper garnish (1) to disengage clips and
remove center pillar upper garnish from the body side panel.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
• When installing, check in advance that clips are accurately aligned with the holes on body panel
side, and then install by pressing in.
• Never reuse front pillar garnish fixing anchor clip. Always replace it with a new one when it is
removed.
: Pawl
JMJIA1369ZZ
: Metal clip
JMJIA1370ZZ
JMJIA1371ZZ
INT-24
< REMOVAL AND INSTALLATION >
FLOOR TRIM
FLOOR TRIM
Exploded View
INFOID:0000000009720370
LHD models
Removal and Installation
INFOID:0000000009720371
REMOVAL
1.
Remove front seat assembly (LH and RH). Refer to
SE-98, "Removal and Installation"
2.
Remove rear seat assembly (LH and RH). Refer to
SE-109, "Removal and Installation"
3.
Remove dash side finisher (LH and RH), front kicking plate inner (LH and RH), center pillar lower garnish
(LH and RH), and rear kicking plate inner (LH and RH). Refer to
INT-20, "Removal and Installation"
.
4.
Remove center console assembly. Refer to
IP-23, "Removal and Installation"
5.
Remove instrument stay fixing nuts (A), and then remove instrument stay (1).
Remove rear foot duct (2), rear foot duct (3) and rear ventilator duct (4).
JMJIA6882ZZ
1.
Floor carpet assembly
2.
Harness protector
3.
Front floor spacer RH
4.
Front floor spacer LH
: Pawl
: Vehicle front
JMJIA1373ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст