Nissan Murano. Manual — part 757
FRONT DRIVE SHAFT
FAX-23
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
9.
Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” mark) on the housing assembly or joint sub-assem-
bly, boot may be removed. Remove all grease from the boot
mounting surface.
10. To prevent the deformation of the boot, adjust the boot installa-
tion length (L) to the specified value shown below by inserting
the suitable tool into inside of the boot from the large diameter
side of the boot and discharging the inside air.
CAUTION:
• If the boot mounting length exceeds the standard, it may cause breakage of boot.
• Be careful not to touch the inside of the boot with a tip of tool.
11. Secure the large and small ends of the boot with boot bands
using the boot band crimping tool (A) [SST: KV40107300 (
—
)].
CAUTION:
Never reuse boot band.
NOTE:
Secure boot band so that dimension (A) meets the specification
as shown in the figure.
12. Secure joint sub-assembly and housing assembly, and then
make sure that they are in the correct position when rotating
boot. Reinstall them using boot bands when boot installation
positions become incorrect.
CAUTION:
Never reuse boot band.
TRANSAXLE SIDE
TRANSAXLE SIDE : Disassembly and Assembly
INFOID:0000000009717905
DISASSEMBLY
Left Side
1.
Fix drive shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2.
Disassemble boot (wheel side). Refer to
FAX-22, "WHEEL SIDE : Disassembly and Assembly"
3.
Remove boot bands and boot (transaxle side).
Right Side
1.
Fix drive shaft with a vise.
CAUTION:
Protect shaft using aluminum or copper plates when fixing with a vise.
2.
Disassemble boot (wheel side). Refer to
FAX-22, "WHEEL SIDE : Disassembly and Assembly"
L
: Refer to
.
JPDIF0222ZZ
JPDIF0012ZZ
A
: 7.0 mm (0.276 in) or less
JPDIF0268ZZ
FAX-24
< REMOVAL AND INSTALLATION >
[2WD]
FRONT DRIVE SHAFT
3.
Remove boot bands and boot (transaxle side).
4.
Remove support bearing, follow the procedure described below.
a.
Remove dust shield.
b.
Remove snap ring (1).
c.
Press out bearing housing and support bearing from housing
assembly.
d.
Remove dust shield.
e.
Remove snap ring (1).
JPDIF0121ZZ
JPDIF0073ZZ
SFA693
JPDIF0177ZZ
FRONT DRIVE SHAFT
FAX-25
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
f.
Press out support bearing from bearing housing (1) with suitable
drift (A) [SST: ST17130000 (
—
)].
5.
Remove dynamic damper, follow the procedure described
below.
a.
Remove damper bands.
b.
Remove dynamic damper from shaft.
ASSEMBLY
Left Side
1.
Install dust shield.
CAUTION:
Never reuse dust shield.
2.
Install circular clip.
CAUTION:
Never reuse circular clip.
3.
Clean old grease on housing assembly with paper waste.
4.
Install boot securely into grooves (indicated by “*” marks) shown
in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” mark) on housing assembly, boot may be removed.
Remove all grease from the boot mounting surface.
5.
To prevent the deformation of the boot, adjust the boot installa-
tion length (L) to the specified value shown below by inserting
the suitable tool into the inside of boot from the large diameter
side of boot and discharging inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of boot.
• Be careful not to touch the inside of the boot with the tip of tool.
6.
Install boot bands securely as shown in the figure.
a.
Put boot band in the groove on drive shaft boot. Then fit pawls
(
) into holes to temporary installation.
NOTE:
For the large diameter side, fit projection (A) and guide slit (B) at
first.
JPDIF0151ZZ
L
: Refer to
JPDIF0144ZZ
JPDIF0157ZZ
FAX-26
< REMOVAL AND INSTALLATION >
[2WD]
FRONT DRIVE SHAFT
b.
Pinch projection on the band with suitable pliers to tighten band.
c.
Insert tip of band below end of the pawl.
7.
Secure housing assembly, and then make sure that they are in
the correct position when rotating boot. Reinstall them with boot
bands when the mounting positions become incorrect.
Right Side
1.
Install dust shield.
CAUTION:
Never reuse dust shield.
2.
Install circular clip.
CAUTION:
Never reuse circular clip.
3.
Install support bearing, follow the procedure described below.
a.
Press support bearing to bearing housing (1) with suitable drift
(A) [SST: ST35271000 (
—
)].
b.
Install snap ring (1).
CAUTION:
Never reuse snap ring.
c.
Install bearing housing and support bearing to housing assem-
bly.
d.
Install snap ring (1).
CAUTION:
Never reuse snap ring.
JPDIF0158ZZ
JPDIF0151ZZ
JPDIF0177ZZ
JPDIF0073ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст