Nissan Murano. Manual — part 1513
WW-120
< SYMPTOM DIAGNOSIS >
WIPER AND WASHER SYSTEM SYMPTOMS
Front wiper does not
stop.
HI only
• Combination switch
• BCM
Combination switch
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
“FR WIP REQ”
IPDM E/R
—
LO only
• Combination switch
• BCM
Combination switch
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
“FR WIP REQ”
IPDM E/R
—
INT only
• Combination switch
• BCM
Combination switch
Refer to
Front wiper request signal
• BCM
• IPDM E/R
IPDM E/R DATA MONITOR
“FR WIP REQ”
Front wiper does not
operate normally.
Intermittent adjustment
cannot be performed.
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
BCM
—
Intermittent control
linked with vehicle
speed cannot be per-
formed.
Check the vehicle speed detection wiper setting.
Refer to
WW-20, "WIPER : CONSULT Function (BCM - WIPER)"
NOTE:
Factory setting of the front wiper intermitted operation is the operation without ve-
hicle speed.
Wiper is not linked to
the washer operation.
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
BCM
—
Does not return to stop
position. [Repeatedly
operates for 10 sec-
onds and then stops
for 20 seconds. After
that, it stops the opera-
tion. (Fail-safe)]
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper stop position sig-
nal circuit
Refer to
.
Rear wiper does not
operate.
ON only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
INT only
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
ON and INT
• Combination switch
• Harness between combination switch and BCM
• BCM
Combination switch
Refer to
• BCM
• Harness between rear wiper motor and BCM
• Harness between rear wiper motor and ground
• Rear wiper motor
Rear wiper motor circuit
Refer to
.
Symptom
Probable malfunction location
Inspection item
WIPER AND WASHER SYSTEM SYMPTOMS
WW-121
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Rear wiper does not
stop.
ON only
• Combination switch
• BCM
Combination switch
Refer to
INT only
• Combination switch
• BCM
Combination switch
Refer to
Rear washer is in the active condition, but
washer fluid is sprayed from rear view camera
side.
Washer switching solenoid valve
Washer switching solenoid
valve circuit
Refer to
Symptom
Probable malfunction location
Inspection item
WW-122
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000009719759
FRONT WIPER MOTOR PROTECTION FUNCTION
• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)
such as a large amount of snow is detected during the front wiper operation.
• At that time turn OFF the front wiper and remove the foreign object. Then wait for approximately 20 seconds
or more and reactivate the front wiper. The wiper will operate normally.
REAR WIPER MOTOR PROTECTION FUNCTION
• BCM may stop rear wiper to protect the rear wiper motor when the rear wiper is stopped for 5 seconds or
more due to a snowfall.
• Rear wiper operates normally one minute after the obstacles are removed with rear wiper OFF.
FRONT WIPER DOES NOT OPERATE
WW-123
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER DOES NOT OPERATE
Description
INFOID:0000000009719760
The front wiper does not operate under any operation conditions.
Diagnosis Procedure
INFOID:0000000009719761
1.
CHECK WIPER RELAY OPERATION
IPDM E/R AUTO ACTIVE TEST
1.
Start IPDM E/R auto active test. Refer to
PCS-10, "Diagnosis Description"
2.
Check that the front wiper operates at the LO/HI operation.
CONSULT ACTIVE TEST
1.
Select “FRONT WIPER” of IPDM E/R active test item.
2.
With operating the test item, check front wiper operation.
Is front wiper operation normally?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR FUSE
1.
Turn the ignition switch OFF.
2.
Check that the front wiper motor 30 A fuse (#60) is not fusing.
Is the fuse fusing?
YES
>> Replace the fuse after repairing the applicable circuit.
NO
>> GO TO 3.
3.
CHECK FRONT WIPER MOTOR GROUND OPEN CIRCUIT
1.
Disconnect front wiper motor connector.
2.
Check continuity between front wiper motor harness connector and ground.
Does continuity exist?
YES
>> GO TO 4.
NO
>> Repair the harness or connector.
4.
CHECK FRONT WIPER MOTOR OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1.
Turn the ignition switch ON.
2.
Select “FRONT WIPER” of IPDM E/R active test item.
3.
With operating the test item, check voltage between IPDM E/R harness connector and ground.
Lo
: Front wiper LO operation
Hi
: Front wiper HI operation
Off
: Stop the front wiper.
Front wiper motor
Ground
Continuity
Connector
Terminal
E12
2
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст