Nissan Murano. Manual — part 27
ADP-100
< DTC/CIRCUIT DIAGNOSIS >
MIRROR SENSOR
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
ADP-100, "PASSENGER SIDE : Diagnosis Procedure"
.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000009720746
1.
CHECK DOOR MIRROR SENSOR (PASSENGER SIDE) POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect door mirror (passenger side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-211, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
3.
CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR GROUND
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) connector.
Monitor item
Condition
Value
MIR/SEN RH U-D
Door mirror (passenger side)
Change between
3.4 [V] (close to peak)
0.6 [V] (close to valley)
MIR/SEN RH R-L
Change between
3.4 [V] (close to left edge)
0.6 [V] (close to right edge)
(+)
(–)
Voltage (V)
(Approx.)
Door mirror (passenger side)
Connector
Terminals
D43
23
Ground
5
Automatic drive positioner control unit
Door mirror (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M75
21
D43
23
Existed
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
21
Not existed
MIRROR SENSOR
ADP-101
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness or connector.
4.
CHECK DOOR MIRROR (PASSENGER SIDE) SENSOR HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and door mirror (passenger side) connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror (pas-
senger side) harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace door mirror sensor. (Built in passenger side door mirror.)
NO
>> Repair or replace harness or connector.
Automatic drive positioner control unit
Door mirror (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M75
20
D43
24
Existed
Automatic drive positioner control unit
Door mirror (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M75
5
D43
21
Existed
17
22
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
5
Not existed
17
ADP-102
< DTC/CIRCUIT DIAGNOSIS >
SLIDING MOTOR
SLIDING MOTOR
Description
INFOID:0000000009720747
• The sliding motor is installed to the seat cushion frame.
• The sliding motor is installed with the driver seat control unit.
• The seat is slid forward/backward by changing the rotation direction of sliding motor.
Component Function Check
INFOID:0000000009720748
1.
CHECK FUNCTION
1.
Select “SEAT SLIDE” in “Active test” mode with CONSULT.
2.
Check the sliding motor operation.
Is the operation of relevant parts normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
ADP-102, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000009720749
1.
CHECK SLIDING MOTOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect sliding motor connector.
3.
Turn the ignition switch ON.
4.
Perform “Active test” (“SEAT SLIDE”) with CONSULT.
5.
Check voltage between sliding motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding motor. (Built in seat slide cushion frame.)
NO
>> GO TO 2.
2.
CHECK SLIDING MOTOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect driver seat control unit connector.
3.
Check continuity between driver seat control unit harness connector and sliding motor harness connector.
Test item
Description
SEAT SLIDE
OFF
Seat sliding
Stop
FR
Forward
RR
Backward
(+)
(–)
Condition
Voltage (V)
(Approx.)
Sliding motor
Connector
Terminals
B461
51
Ground
SEAT SLIDE
OFF
0
FR (forward)
Battery voltage
RR (backward)
0
50
OFF
0
FR (forward)
0
RR (backward)
Battery voltage
Driver seat control unit
Sliding motor
Continuity
Connector
Terminal
Connector
Terminal
B451
4
B461
51
Existed
3
50
SLIDING MOTOR
ADP-103
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4.
Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace driver seat control unit. Refer to
ADP-210, "Removal and Installation"
NO
>> Repair or replace harness or connector.
Driver seat control unit
Ground
Continuity
Connector
Terminal
B451
4
Not existed
3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст