Nissan Murano. Manual — part 1348
ST-86
< REMOVAL AND INSTALLATION >
[WITHOUT HEATED STEERING WHEEL]
LOWER SHAFT
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Spiral cable may be cut if steering wheel turns while separating steering column assembly and steer-
ing gear assembly. Be sure to secure steering wheel using string to avoid turning.
• Tighten the clamp to the specified torque and check the clamp
length (A).
• After lower shaft (steering gear side) fitted, make sure there is not
gap (A) between the yoke (1), lower shaft (2), joint fixing bolt (3).
• When installing lower joint to steering gear assembly, follow the procedure listed below.
- Set rack of steering gear in the neutral position.
NOTE:
To get the neutral position of rack, turn gear-sub assembly and measure the distance of inner socket, and
then measure the intermediate position of the distance.
- Align rear cover cap projection (A) with the marking position of
gear housing assembly (B).
- Install slit part of lower joint (C) aligning with the rear cover cap
projection (A). Make sure that the slit part of lower joint (C) is
aligned with rear cover cap projection (A) and the marking position
of gear housing assembly (B).
• Adjust neutral position of steering angle sensor. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Special Repair Requirement"
.
• Check the following after installation:
- Check if steering wheel turns smoothly when it is turned several times fully to the end of the left and right.
- Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
Clamp length “A”
: 14.0 – 18.0 mm (0.551 –
0.709 in)
JSGIA0094ZZ
JSGIA0180ZZ
: Bolt
JSGIA0313ZZ
LOWER SHAFT
ST-87
< REMOVAL AND INSTALLATION >
[WITHOUT HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Inspection
INFOID:0000000009721530
• Check the length (A) (extended position) of the lower shaft.
• Check each part of lower shaft for damage or other malfunctions.
Replace if there are.
Standard
Lower shaft length (A)
: Refer to
.
JSGIA0314ZZ
ST-88
< REMOVAL AND INSTALLATION >
[WITHOUT HEATED STEERING WHEEL]
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE
Exploded View
INFOID:0000000009721531
REMOVAL
2WD models
AWD models
DISASSEMBLY
JSGIA0606GB
1.
Steering gear assembly
2.
Cotter pin
: Vehicle front
Refer to
for symbols in the figure.
JSGIA0607GB
1.
Steering gear assembly
2.
Cotter pin
: Vehicle front
Refer to
for symbols in the figure.
STEERING GEAR AND LINKAGE
ST-89
< REMOVAL AND INSTALLATION >
[WITHOUT HEATED STEERING WHEEL]
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
2WD models
JSGIA0571GB
1.
Low pressure piping
2.
Rear cover cap
3.
Gear-sub assembly
4.
Power steering solenoid valve
5.
O-ring
6.
Adjusting screw
7.
Spring
8.
Retainer
9.
Outer socket
10. Boot clamp
11.
Boot
12. Inner socket
13. Boot clamp (stainless wire)
14. Cylinder tube
15. Gear housing assembly
16. Rack oil seal
17. Rack assembly
18. Rack Teflon ring
19. O-ring
20. End cover assembly
: Apply power steering fluid.
: Apply Genuine Medium Strength Thread Locking Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Prod-
.
: Apply Genuine High Performance Thread Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Products and
: Apply multi-purpose grease.
Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст