Nissan Murano. Manual — part 523
EC-202
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0130, P0150 A/F SENSOR 1
3.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4.
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
5.
Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
5.
CHECK INTERMITTENT INCIDENT
Perform
GI-44, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning part.
6.
REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace malfunctioning air fuel ratio (A/F) sensor 1.
CAUTION:
• Discard any A/F sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
• Before installing new A/F sensor, clean exhaust system threads using Oxygen Sensor Thread
Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved anti-seize lubricant
(commercial service tool).
>> INSPECTION END
DTC
A/F sensor 1
ECM
Continuity
Bank
Connector
Terminal
Connector
Terminal
P0130
1
F27
1
F8
45
Existed
2
49
P0150
2
F64
1
53
2
57
DTC
A/F sensor 1
Ground
Continuity
Bank
Connector
Terminal
P0130
1
F27
1
Ground
Not existed
2
P0150
2
F64
1
2
DTC
ECM
Ground
Continuity
Connector
Terminal
P0130
F8
45
Ground
Not existed
49
P0150
53
57
P0131, P0151 A/F SENSOR 1
EC-203
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0131, P0151 A/F SENSOR 1
Description
INFOID:0000000009719949
The air fuel ratio (A/F) sensor 1 is a planar one-cell limit current sen-
sor. The sensor element of the A/F sensor 1 is composed an elec-
trode layer, which transports ions. It has a heater in the element.
The sensor is capable of precise measurement = 1, but also in the
lean and rich range. Together with its control electronics, the sensor
outputs a clear, continuous signal throughout a wide range.
The exhaust gas components diffuse through the diffusion layer at
the sensor cell. An electrode layer is applied voltage, and this current
relative oxygen density in lean. Also this current relative hydrocar-
bon density in rich.
Therefore, the A/F sensor 1 is able to indicate air fuel ratio by this
electrode layer of current. In addition, a heater is integrated in the
sensor to ensure the required operating temperature of approxi-
mately 800
°
C (1,472
°
F).
DTC Logic
INFOID:0000000009719950
DTC DETECTION LOGIC
To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1
signal is not inordinately low.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10.5 V at idle.
>> GO TO 2.
2.
CHECK A/F SENSOR 1 FUNCTION
With CONSULT
1.
Start engine and warm it up to normal operating temperature.
2.
Select “A/F SEN1 (B1)” or “A/F SEN1 (B2)” in “DATA MONITOR” mode with CONSULT.
3.
Check “A/F SEN1 (B1)” or “A/F SEN1 (B2)” indication.
JMBIA0112GB
PBIB3354E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0131
Air fuel ratio (A/F) sensor 1
(bank 1) circuit low voltage
• The A/F signal computed by ECM from the A/
F sensor 1 signal is constantly approx. 0 V.
• Harness or connectors
(The A/F sensor 1 circuit is open or
shorted.)
• A/F sensor 1
P0151
Air fuel ratio (A/F) sensor 1
(bank 2) circuit low voltage
EC-204
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P0131, P0151 A/F SENSOR 1
With GST
Follow the procedure “With CONSULT” above.
Is the indication constantly approx. 0 V?
YES
>> Go to
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
1.
Turn ignition switch OFF, wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF, wait at least 10 seconds and then restart engine.
4.
Drive and accelerate vehicle to more than 40 km/h (25 MPH) within 20 seconds after restarting engine.
CAUTION:
Always drive vehicle at a safe speed.
5.
Maintain the following conditions for approximately 20 consecutive seconds.
NOTE:
• Keep the accelerator pedal as steady as possible during cruising.
• If this procedure is not completed within 1 minute after restarting engine at step 1, return to step
1.
6.
Check 1st trip DTC.
With GST
Follow the procedure “With CONSULT” above.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009719951
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection E38. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
1.
Disconnect A/F sensor 1 harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between A/F sensor 1 harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
DETECT MALFUNCTIONING PART
Check the following.
ENG SPEED
1,000 - 3,200 rpm
VHCL SPEED SE
More than 40 km/h (25 mph)
B/FUEL SCHDL
1.5 - 9.0 msec
Selector lever
Suitable position
DTC
A/F sensor 1
Ground
Voltage
Bank
Connector
Terminal
P0131
1
F27
4
Ground
Battery voltage
P0151
2
F64
4
P0131, P0151 A/F SENSOR 1
EC-205
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
• IPDM E/R harness connector F12
• 15 A fuse (No. 46)
• Harness for open or short between A/F sensor 1 and IPDM E/R
>> Repair or replace harness or connectors.
4.
CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4.
Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector
and ground.
5.
Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
5.
CHECK INTERMITTENT INCIDENT
Perform
GI-44, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning part.
6.
REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace malfunctioning air fuel ratio (A/F) sensor 1. Refer to
.
CAUTION:
• Discard any A/F sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a
hard surface such as a concrete floor; use a new one.
• Before installing new A/F sensor, clean exhaust system threads using Oxygen Sensor Thread
Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved anti-seize lubricant
(commercial service tool).
DTC
A/F sensor 1
ECM
Continuity
Bank
Connector
Terminal
Connector
Terminal
P0131
1
F27
1
F8
45
Existed
2
49
P0151
2
F64
1
53
2
57
DTC
A/F sensor 1
Ground
Continuity
Bank
Connector
Terminal
P0131
1
F27
1
Ground
Not existed
2
P0151
2
F64
1
2
DTC
ECM
Ground
Continuity
Connector
Terminal
P0131
F8
45
Ground
Not existed
49
P0151
53
57
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст