Nissan Terrano model r20 series 2004. Manual — part 277
6. Install drive pinion bearing spacer, pinion bearing adjusting
shim and drive pinion in gear carrier.
7. Insert companion flange into drive pinion by tapping the com-
panion flange with a soft hammer.
8. Tighten pinion nut to specified torque.
The threaded portion of drive pinion and pinion nut should be
free from oil or grease.
Tool number:
KV38104700
9. Turn drive pinion in both directions several times, and measure
pinion bearing preload.
Tool number:
ST3127S000
Pinion bearing preload:
1.1 - 1.6 N
⋅
m (11.2 - 16.3 kg-cm, 9.7 - 14.1 in-lb)
10. Install differential case assembly with side bearing outer races
into gear carrier.
SPD712
SPD697
SPD040
SPD149
PD383
ASSEMBLY (C200)
Differential Carrier (Cont’d)
PD-54
11. Position side bearing on gear carrier with threads properly
engaged; screw in adjusters lightly at this stage of assembly.
Tool number:
ST32580000
12. Align mark on bearing cap with that on gear carrier and install
bearing cap on gear carrier.
I
Do not tighten at this point to allow further tightening of side
bearing adjusters.
13. Tighten both right and left side bearing adjusters alternately and
measure ring gear backlash and total preload at the same time.
Adjust right and left side bearing adjusters by tightening them
alternately so that proper ring gear backlash and total preload
can be obtained.
Ring gear-to-drive pinion backlash:
0.10 - 0.20 mm (0.0039 - 0.0079 in)
I
When checking preload, turn drive pinion in both direc-
tions several times to set bearing rollers.
Tool number:
ST3127S000
The total pinion bearing preload value with the differential case
assembly should be in accordance with the same value measured
without the differential case assembly. (See point 9.)
The relationship between both is:
Pinion bearing preload
With differential case assembly
Without differential case assembly
kg-cm
N
⋅
m
kg-cm
N
⋅
m
14
1.4
17 - 23
1.7 - 2.3
15
1.5
18 - 24
1.8 - 2.4
16
1.6
19 - 25
1.9 - 2.5
17
1.7
20 - 26
2.0 - 2.6
SPD684
SPD265
SPD246
SPD149
ASSEMBLY (C200)
Differential Carrier (Cont’d)
PD-55
14. Tighten side bearing cap bolts.
: 88 - 98 N
⋅
m (9.0 - 9.9 kg-m, 65 - 72 ft-lb)
15. Install side lock finger in place to prevent rotation during opera-
tion.
16. Check runout of ring gear with a dial indicator.
Runout limit:
0.08 mm (0.0031 in)
I
If backlash varies excessively in different places, the variance
may have resulted from foreign matter caught between the ring
gear and the differential case.
I
If the backlash varies greatly when the runout of the ring gear
is within a specified range, the hypoid gear set or differential
case should be replaced.
17. Check tooth contact. (Refer to PD-49.)
SPD698
SPD247
ASSEMBLY (C200)
Differential Carrier (Cont’d)
PD-56
Propeller Shaft
GENERAL SPECIFICATIONS
Unit: mm (in)
MODEL
ALL
H/T
WAGON
Portion
Front
Rear
Propeller shaft
model
0F71H
2S80B
Number of joints
2
Coupling
method with
transmission
Flange type
Sleeve type
Types of journal
bearings
Solid type (dis-
assembly type)
Solid type
Shaft length
(Spider to spi-
der)
mm (in)
569 (22.40)
750 (29.53)
950 (37.40)
Shaft outer
diameter mm (in)
65 (2.56)
65 (2.56)
INSPECTION AND ADJUSTMENT
Front propeller shaft
Unit: mm (in)
Propeller shaft model
0F71H
Journal axial play limit
0.02 (0.0008)
Propeller shaft runout limit
0.6 (0.024)
Measuring point A
L/2
YPD011
Rear propeller shaft
Unit: mm (in)
Propeller shaft model
2S80B
Journal axial play limit
0.02 (0.0008)
Propeller shaft runout limit
0.6 (0.024)
Measuring point A
L/2
YPD012
Available snap rings
0F71H models
Unit: mm (in)
Thickness mm (in)
Part number
1.25 (0.0492)
37150-2X800
1.30 (0.0512)
37149-2X800
1.35 (0.0531)
37148-2X800
1.40 (0.0551)
37147-2X800
1.45 (0.0571)
37146-2X800
2S80B models
Thickness mm (in)
Part number
1.45 (0.0571)
37146-7F000
1.50 (0.0591)
37147-7F000
1.55 (0.0610)
37148-7F000
1.60 (0.0630)
37149-7F000
1.65 (0.0650)
37150-7F000
1.70 (0.0669)
37151-7F000
1.75 (0.0689)
37152-7F000
SERVICE DATA AND SPECIFICATIONS (SDS)
PD-57
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст