Murano Cross Cabriolet Z51 (2011 year). Manual — part 53
FRONT PASSENGER AIR BAG MODULE
SR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000007228839
Removal and Installation
INFOID:0000000007228840
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Disconnect front passenger air bag harness connector (A).
3.
Remove front passenger air bag module mounting bolt (B).
NOTE:
The figure shows the installed front passenger air bag module.
(Under view of the module installed without glove box cover.)
1.
Instrument panel assembly
2.
Front passenger air bag module
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA0509GB
JMHIA0510ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
SR-18
< REMOVAL AND INSTALLATION >
FRONT PASSENGER AIR BAG MODULE
4.
Remove front passenger air bag module fixing screws (B) from
instrument panel assembly (1).
5.
Disconnect pawls (C) by using remover tool (A), and then
remove front passenger air bag module (2) from instrument
panel assembly.
CAUTION:
• Always place the front passenger air bag module with pad
side facing upward.
• Never impact the passenger air bag module.
• Replace the front passenger air bag module if it is dropped or
sustains an impact.
• Never insert any foreign objects (screwdriver, etc.) into front passenger air bag module.
• Never disassembly the front passenger air bag module.
• Never expose the front passenger air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the front passenger air bag mod-
ule.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Never reuse fixing bolts after removal, replace with new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0511ZZ
: Upward
JMHIA0512ZZ
JMHIA0009ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
DOOR-MOUNTED CURTAIN AIR BAG MODULE
SR-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
DOOR-MOUNTED CURTAIN AIR BAG MODULE
Exploded View
INFOID:0000000007228855
Removal and Installation
INFOID:0000000007228856
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more.
• Before starting removal and installation operation, always eliminate static electricity from door fin-
isher, door-mounted curtain air bag module, and body of the technician (to prevent an accidental
activation due to static electricity).
• Never use air tools or electric tools for servicing.
• When replacing door-mounted curtain air bag module, always replace it together with door finisher
as a set.
REMOVAL
1.
Remove door finisher. Refer to
INT-13, "Removal and Installation"
CAUTION:
Disconnect first the door-mounted curtain air bag harness connector before disconnecting the
other harness connectors.
JMHIA2064GB
1.
Door finisher
2.
Door-mounted curtain air bag module
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
Revision: 2012 March
2011 Murano CrossCabriolet
SR-20
< REMOVAL AND INSTALLATION >
DOOR-MOUNTED CURTAIN AIR BAG MODULE
2.
Remove door-mounted curtain air bag module fixing screws (A)
and mounting bolts (B).
3.
Remove door-mounted curtain air bag module.
CAUTION:
• Never place any object in deploying path of door-mounted
curtain air bag module. Never lean door-mounted curtain air
bag module against wall or others.
• Always place air bag module so that inflator label is visible.
• Never impact the door-mounted curtain air bag module.
• Replace door-mounted curtain air bag module if it is dropped
or sustains an impact.
• Never insert any foreign objects (screwdriver, etc.) into the door-mounted curtain air bag module.
• Never disassemble the door-mounted curtain air bag module.
• Never expose the door-mounted curtain air bag module to temperatures exceeding 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the door-mounted curtain air bag
module.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• When removing door-mounted curtain air bag module from door finisher, never reuse door finisher.
• Never forget to tighten the mounting bolts and fixing screws of door-mounted curtain air bag mod-
ule.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
or
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA2065ZZ
: Upward
JMHIA2066ZZ
JMHIA0009ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
POP-UP ROLL BAR
SR-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
POP-UP ROLL BAR
Exploded View
INFOID:0000000007228859
Removal and Installation
INFOID:0000000007228860
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more.
• Never use air tools or electric tools for servicing.
• When repairing, removing and installing pop-up roll bar, always refer to SRS AIR BAG and SRS AIR
BAG CONTROL SYSTEM.
CAUTION:
1.
Pup-up roll bar assembly
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA2068GB
Revision: 2012 March
2011 Murano CrossCabriolet
SR-22
< REMOVAL AND INSTALLATION >
POP-UP ROLL BAR
Glass breaking pin is sharp. For safety purposes, protect glass breaking pin (A) of pop-up roll bar
using polystyrene foam or rubber sheet so that glass breaking pin does not contact operator during
removal and installation.
REMOVAL
1.
Open trunk lid.
2.
Remove trunk front finisher. Refer to
INT-36, "TRUNK FRONT FINISHER : Removal and Installation"
.
3.
Remove pop-up roll bar assembly mounting bolts (A) for trunk
room side.
4.
Close trunk lid.
5.
Fully open soft top.
6.
Remove rear seatback. Refer to
SE-57, "SEATBACK : Removal and Installation"
7.
Remove rear parcel shelf front finisher. Refer to
INT-30, "REAR PARCEL SHELF FRONT FINISHER :
.
8.
Remove pop-up roll bar assembly mounting bolts (A) for rear
seatback side.
9.
Disconnect pop-up roll bar assembly harness connector (A).
10. Pull up and remove pop-up roll bar assembly.
JMHIA2093ZZ
: Vehicle front
JMHIA2071ZZ
: Vehicle front
JMHIA2070ZZ
: Vehicle front
JMHIA2069ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
POP-UP ROLL BAR
SR-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CAUTION:
• Always place the pop-up roll bar assembly with special bolts
side facing upward.
• Never place any object in deploying path of pop-up roll bar
assembly. Never lean pop-up roll bar assembly against a wall
or others.
• Never impact the pop-up roll bar assembly.
• Replace pop-up roll bar assembly if it is dropped or sustained
an impact.
• Never insert any foreign objects (screwdriver, etc.) into the pop-up roll bar assembly.
• Never disassemble the pop-up roll bar assembly.
• Never expose the pop-up roll bar assembly to temperatures of more than 90
°
C (194
°
F).
• Never allow oil, grease, detergent, or water to come in contact with the pop-up roll bar assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse old mounting bolts after removal, replace with new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Removal When Pop-up Roll Bar is Activated While Soft Top is Closed
When rear glass is broken and pop-up roll bar is deployed
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 minutes
or more.
CAUTION:
Remove broken pieces of rear glass in advance for preventing injury.
1.
Open trunk lid.
2.
Remove trunk front finisher. Refer to
INT-36, "TRUNK FRONT FINISHER : Removal and Installation"
.
: Upward
JMHIA2072ZZ
JMHIA0009ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
SR-24
< REMOVAL AND INSTALLATION >
POP-UP ROLL BAR
3.
Remove pop-up roll bar assembly mounting bolts (A) of trunk
room side.
4.
Close trunk lid.
5.
Remove rear seatback. Refer to
SE-57, "SEATBACK : Removal and Installation"
6.
Remove rear parcel shelf front finisher. Refer to
INT-30, "REAR PARCEL SHELF FRONT FINISHER :
.
7.
Remove pop-up roll bar assembly mounting bolts (A) of rear
seatback side.
8.
Disconnect pop-up roll bar assembly harness connector (A).
9.
Pull out pop-up roll bar from rear glass portion to upward.
When pop-up roll bar is deployed and rear glass is not broken
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 minutes
or more.
1.
Open trunk lid.
2.
Remove trunk front finisher. Refer to
INT-36, "TRUNK FRONT FINISHER : Removal and Installation"
.
: Vehicle front
JMHIA2071ZZ
: Vehicle front
JMHIA2070ZZ
: Vehicle front
JMHIA2069ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
POP-UP ROLL BAR
SR-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
3.
Remove pop-up roll bar assembly mounting bolts (A) of trunk
room side.
4.
Close trunk lid.
5.
Slide down pop-up roll bar.
CAUTION:
Fix pop-up roll bar using fixing band so that pop-up roll bar may not move upward.
6.
Fully open soft top.
7.
Remove rear seatback. Refer to
SE-57, "SEATBACK : Removal and Installation"
8.
Remove rear parcel shelf front finisher. Refer to
INT-30, "REAR PARCEL SHELF FRONT FINISHER :
.
9.
Remove pop-up roll bar assembly mounting bolts (A) of rear
seatback side.
10. Disconnect pop-up roll bar assembly harness connector (A).
11. Pull up and remove pop-up roll bar assembly.
: Vehicle front
JMHIA2071ZZ
: Vehicle front
JMHIA2070ZZ
: Vehicle front
JMHIA2069ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
SR-26
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Exploded View
INFOID:0000000007228843
Removal and Installation
INFOID:0000000007228844
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more.
• Never use air tools or electric tools for servicing.
REMOVAL
1.
Remove radiator cover grill (RH). Refer to
2.
Remove air duct (inlet). Refer to
3.
Remove crash zone sensor fixing nuts.
4.
Disconnect crash zone sensor harness connector, and then remove the crash zone sensor.
CAUTION:
• Never impact the crash zone sensor.
• Replace the crash zone sensor if it is dropped or sustains an
impact.
• Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger air
bag.
INSTALLATION
1.
Crash zone sensor
A
: Crash zone sensor harness connector
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA0515GB
JMHIA0009ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
CRASH ZONE SENSOR
SR-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
Install in the reverse order of removal.
CAUTION:
• Never reuse old fixing nuts after removal, replace with new nuts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Revision: 2012 March
2011 Murano CrossCabriolet
SR-28
< REMOVAL AND INSTALLATION >
SATELLITE SENSOR
SATELLITE SENSOR
Exploded View
INFOID:0000000007228898
Removal and Installation
INFOID:0000000007228899
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more.
• Never use air tools or electric tools for servicing.
DOOR SATELLITE SENSOR
Removal
1.
Remove door finisher. Refer to
INT-13, "Removal and Installation"
.
2.
Remove door satellite sensor mounting bolt.
3.
Disconnect harness connector, and then remove door satellite sensor.
CAUTION:
1.
Door satellite sensor
2.
Satellite sensor
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA2067GB
Revision: 2012 March
2011 Murano CrossCabriolet
SATELLITE SENSOR
SR-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Never impact the door satellite sensor.
• Replace the door satellite sensor if it is dropped or sustains
an impact.
• Replace the door satellite sensor of deployed side air bag module and deployed door-mounted cur-
tain air bag module.
Installation
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse fixing nut after removal, replace with new nut.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
SATELLITE SENSOR
Removal
1.
Remove rear side finisher. Refer to
INT-22, "REAR SIDE FINISHER : Removal and Installation"
2.
Remove front seat belt retractor. Refer to
SB-5, "SEAT BELT RETRACTOR : Removal and Installation"
.
3.
Remove satellite sensor mounting nut.
4.
Disconnect harness connector, and then remove satellite sensor.
CAUTION:
• Never impact the satellite sensor.
• Replace the satellite sensor if it is dropped or sustains an
impact.
• Replace the satellite sensor of deployed side air bag module and deployed door-mounted curtain air
bag module.
Installation
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse fixing nut after removal, replace with new nut.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA0009ZZ
JMHIA0009ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
SR-30
< REMOVAL AND INSTALLATION >
DIAGNOSIS SENSOR UNIT
DIAGNOSIS SENSOR UNIT
Exploded View
INFOID:0000000007228847
Removal and Installation
INFOID:0000000007228848
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more.
• Before disconnecting the air bag sensor unit harness connector, be sure to disconnect the each har-
ness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by
static electricity and pre-tensioner seat belt operation.
• Never use air tools or electric tools for servicing.
• When replacing the air bag diagnosis sensor unit, always check with the parts department for the lat-
est parts information. Installing an incorrect air bag diagnosis sensor unit may or may not cause the
air bag warning lamp to illuminate and may cause incorrect deployment of the supplemental air bags
and seat belt pre-tensioners in a collision resulting in serious personal injury or death.
REMOVAL
1.
Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) using
CONSULT.
2.
Disconnect each connector of all air bag modules and pre-tensioner seat belts.
3.
Remove instrument lower cover (LH and RH). Refer to
.
4.
Remove rear foot duct 1 (LH and RH). Refer to
.
5.
Remove instrument stay LH. Refer to
.
6.
Remove front console bracket. Refer to
.
7.
Disconnect diagnosis sensor unit harness connectors.
8.
Remove fixing bolts, ground bolt, and then remove diagnosis sensor unit.
CAUTION:
1.
Diagnosis sensor unit
A
: Diagnosis sensor unit harness connector
B
: Ground bolt
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA0517GB
Revision: 2012 March
2011 Murano CrossCabriolet
DIAGNOSIS SENSOR UNIT
SR-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
• Replace the diagnosis sensor unit if it is dropped or sustains
an impact.
• Replace the diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat belt pre-
tensioner.
INSTALLATION
Install air bag diagnosis sensor unit in the reverse order of removal.
CAUTION:
• Never reuse mounting bolts after removal, replace with new mounting bolts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• After replacing the air bag diagnosis sensor unit, confirm using CONSULT that the ECU discrimi-
nated number (identification number) of the new replacement air bag sensor unit matches the ECU
discriminated number (identification number) of the replaced (old) air bag diagnosis sensor unit.
NOTE:
If the ECU discriminated number of the new replacement air bag diagnosis sensor unit differs from the ECU
discriminated number of the replaced air bag diagnosis sensor unit, reconfirm the parts information and verify
that the correct air bag diagnosis sensor unit is installed.
JMHIA0009ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
SR-32
< REMOVAL AND INSTALLATION >
FRONT SEAT BELT PRE-TENSIONER
FRONT SEAT BELT PRE-TENSIONER
Removal and Installation
INFOID:0000000007228849
For removal and installation procedures, refer to
SB-5, "SEAT BELT RETRACTOR : Removal and Installa-
.
Revision: 2012 March
2011 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст