Murano Cross Cabriolet Z51 (2011 year). Manual — part 19
WATER INLET AND THERMOSTAT ASSEMBLY
CO-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
Inspection
INFOID:0000000006939280
INSPECTION AFTER REMOVAL
1.
Check valve seating condition at ordinary room temperatures. It should seat tightly.
2.
Check valve operation.
• If the malfunctioning condition, when valve seating at ordinary
room temperature, or measured values are out of the standard,
replace water inlet and thermostat assembly.
INSPECTION AFTER INSTALLATION
• Check for leakage of engine coolant using the radiator cap tester adapter (commercial service tool) and the
radiator cap tester (commercial service tool). Refer to
.
• Start and warm up the engine. Visually check that there is no leakage of engine coolant.
Thermostat (Standard)
: Refer to
.
SLC949A
Revision: 2012 March
2011 Murano CrossCabriolet
CO-26
< REMOVAL AND INSTALLATION >
WATER OUTLET AND WATER PIPING
WATER OUTLET AND WATER PIPING
Exploded View
INFOID:0000000006939281
Removal and Installation
INFOID:0000000006939282
REMOVAL
1.
Remove air duct (inlet), radiator core support covers (RH and LH), air cleaner cases (upper and lower)
with mass air flow sensor and air duct assembly. Refer to
2.
Remove engine cover. Refer to
3.
Drain engine coolant from radiator drain plug at the bottom of radiator, and from water drain plug at the
front of cylinder block. Refer to
.
CAUTION:
1.
Heater hose
2.
Clamp
3.
Water hose
4.
Clamp
5.
Water outlet
6.
Gasket
7.
Gasket
8.
Water connector
9.
O-ring
10. Water bypass pipe
11.
Clamp
12.
Water hose
13. Heater pipe
14.
Water hose
15.
Heater hose
16. Engine coolant temperature sensor
17.
Clamp
18.
Radiator hose (upper)
A.
To heater core
B.
To electric throttle control actuator
C.
To oil cooler
D.
To radiator
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JPBIA1691GB
Revision: 2012 March
2011 Murano CrossCabriolet
WATER OUTLET AND WATER PIPING
CO-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
• Perform this step when the engine is cold.
• Never spill engine coolant on drive belt.
4.
Remove battery and battery tray. Refer to
PG-112, "Removal and Installation"
.
5.
Remove CVT fluid charging pipe and CVT fluid level gauge. Refer to
6.
Move CVT control cable aside. Refer to
7.
Remove vacuum tube (front) mounting bolt from water outlet. Refer to
.
8.
Remove radiator hose (upper) from water outlet.
9.
Remove water hoses and heater hoses.
10. Disconnect harness connectors, and move harness to aside.
11. Remove engine coolant temperature sensor if necessary.
CAUTION:
Never damage engine coolant temperature sensor.
12. Remove water outlet, heater pipe, water bypass pipe and water connector.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Do not reuse O-rings.
• Securely insert each hose, and install clamp at a position where it does not interfere with the pipe bulge.
• When inserting water bypass pipe and heater pipe into water connector, apply neutral detergent to O-ring.
Inspection
INFOID:0000000006939283
INSPECTION AFTER INSTALLATION
• Check for leakage of engine coolant using the radiator cap tester adapter (commercial service tool) and the
radiator cap tester (commercial service tool). Refer to
.
• Start and warm up the engine. Visually check that there is no leakage of engine coolant.
Revision: 2012 March
2011 Murano CrossCabriolet
CO-28
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance Specification
INFOID:0000000006939284
ENGINE COOLANT CAPACITY (APPROXIMATE)
Unit:
(US qt, lmp qt)
Radiator
INFOID:0000000006939285
Unit: kPa (kg/cm
2
, psi)
Thermostat
INFOID:0000000006939286
Standard
Engine coolant capacity (With reservoir tank at “MAX” level)
9.0 (9-1/2, 7-7/8)
Reservoir tank
0.8 (7/8, 3/4)
Cap relief pressure
Standard
122.3 - 151.7 (1.2 - 1.5, 17.7 - 22.0)
Limit
108 (1.1, 15.6)
Leakage test pressure
156 (1.59, 22.6)
Valve opening temperature
80.5 - 83.5
°
C (177 - 182
°
F)
Maximum valve lift
8.6 mm/95
°
C (0.339 in/203
°
F)
Valve closing temperature
77
°
C (171
°
F)
Revision: 2012 March
2011 Murano CrossCabriolet
DEF-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
DEF
A
B
DEF
N
O
P
CONTENTS
DEFOGGER
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . .....
SYSTEM . . . . . . . . . . . . . . . ..
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (BCM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
REAR WINDOW DEFOGGER . . . . . . . . .....
REAR WINDOW DEFOGGER : CONSULT Func-
tion (BCM - REAR DEFOGGER) . . . . . . . ..
DIAGNOSIS SYSTEM (SOFT TOP CONTROL
UNIT) . . . . . . . . . . . . . . . . ...
CONSULT Function . . . . . . . . . . . . ..
ECU DIAGNOSIS INFORMATION . . . ..
BCM . . . . . . . . . . . . . . . . .
List of ECU Reference . . . . . . . . . . .
SOFT TOP CONTROL UNIT . . . . . . . ..
List of ECU Reference . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
REAR WINDOW DEFOGGER SYSTEM . . .
Wiring Diagram . . . . . . . . . . . . . ...
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORKFLOW . .
Work Flow . . . . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
REAR WINDOW DEFOGGER SWITCH . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
REAR WINDOW DEFOGGER RELAY . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
SOFT TOP CONTROL UNIT . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
REAR WINDOW DEFOGGER . . . . . . ..
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
DOOR MIRROR DEFOGGER . . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
DRIVER SIDE DOOR MIRROR DEFOGGER ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
PASSENGER SIDE DOOR MIRROR DEFOG-
GER . . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
SYMPTOM DIAGNOSIS . . . . . . . ..
Revision: 2012 March
2011 Murano CrossCabriolet
DEF-2
REAR WINDOW DEFOGGER AND DOOR
MIRROR DEFOGGERS DO NOT OPERATE ...
Diagnosis Procedure . . . . . . . . . . . ..
REAR WINDOW DEFOGGER DOES NOT
OPERATE BUT BOTH DOOR MIRROR DE-
FOGGERS OPERATE . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
BOTH SIDES . . . . . . . . . . . . . . . .
BOTH SIDES : Diagnosis Procedure . . . . . .
DRIVER SIDE . . . . . . . . . . . . . . ....
DRIVER SIDE : Diagnosis Procedure . . . . ....
PASSENGER SIDE . . . . . . . . . . . . ...
PASSENGER SIDE : Diagnosis Procedure . . .
Diagnosis Procedure . . . . . . . . . . . ...
REAR WINDOW DEFOGGER INDICATOR
DOES NOT ILLUMINATE . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ..
FILAMENT . . . . . . . . . . . . . . .
Inspection and Repair . . . . . . . . . . . .
CONDENSER . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Revision: 2012 March
2011 Murano CrossCabriolet
PRECAUTIONS
DEF-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007202388
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Revision: 2012 March
2011 Murano CrossCabriolet
DEF-4
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000006939181
Component Description
INFOID:0000000006939182
1.
Rear window defogger connector
2.
Door mirror (door mirror defogger)
3.
Rear window defogger switch
(built-in multifunction switch)
4.
AV control unit
5.
IPDM E/R
6.
BCM
7.
Soft top control unit
8.
Condenser
A.
View with trunk front finisher removed
JMLIA2207ZZ
BCM
• Controls the rear window defogger relay with the operation of rear window defogger switch.
• Performs the timer control of rear window defogger.
Rear window defogger relay
• Operates the rear window defogger and the door mirror defogger with the control signal from
BCM.
IPDM E/R
• Transmit rear window defogger control signal to AV control unit via CAN communication.
Multifunction switch
(Rear window defogger
switch)
• The rear window defogger switch is installed.
• Turns the indicator lamp ON when detecting the operation of rear window defogger.
AV control unit
• Displays the rear window defogger ON to the display when detecting the operation of rear win-
dow defogger.
Soft top control unit
• Soft top control unit detects roof state and controls rear window defogger operation.
Rear window defogger
• Heats the heating wire with the power supply from the rear window defogger relay to prevent
the rear window from fogging up.
Door mirror defogger
• Heats the heating wire with the power supply from the rear window defogger relay to prevent
the door mirror from fogging up.
Revision: 2012 March
2011 Murano CrossCabriolet
SYSTEM
DEF-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
SYSTEM
System Diagram
INFOID:0000000006939179
System Description
INFOID:0000000007221065
OPERATION DESCRIPTION
• Turn rear window defogger switch ON when the ignition switch is ON. Then multifunction switch (rear win-
dow defogger switch) transmits rear window defogger switch signal to AV control unit via AV communication.
AV control unit transmits rear window defogger switch signal to BCM via CAN communication.
• BCM turns rear window defogger relay ON and transmits rear window defogger ON signal to IPDM E/R via
CAN communication when rear window defogger switch signal is received.
• Door mirror defoggers are supplied with power and operate when rear window defogger relay turns ON.
• Rear window defogger relay sends power supply to soft top control unit.
• Soft top control unit detects roof state and controls rear window defogger operation.
• IPDM E/R transmits rear window defogger status signal to AV control unit via CAN communication.
• When receiving the signal, AV control unit indicates rear defogger ON on the display. At the same time, AV
control unit transmits rear window defogger status signal to multifunction switch (rear window defogger
switch) via AV communication and illuminates rear window defogger switch indicator.
TIMER FUNCTION
• BCM turns rear window defogger relay ON for approximately 15 minutes when rear window defogger switch
is turned ON. It makes rear window defogger and door mirror defoggers operate.
• Timer is canceled after pressing rear window defogger switch again during timer operation. Then BCM turns
rear window defogger relay OFF. The same operation also occurs during timer operation, if the ignition
switch is turned OFF.
JMLIA2220GB
Revision: 2012 March
2011 Murano CrossCabriolet
DEF-6
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000007258915
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
—
AIR CONDITONER*
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk lid opener system
TRUNK
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
Revision: 2012 March
2011 Murano CrossCabriolet
DIAGNOSIS SYSTEM (BCM)
DEF-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
NOTE:
*: Power supply position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position, and
any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power supply position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
REAR WINDOW DEFOGGER
REAR WINDOW DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER)
INFOID:0000000006939188
Data monitor
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”*)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK” to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”*
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”*) to low power consumption mode
LOCK
Power supply position is “LOCK”*
OFF
Power supply position is “OFF” (Ignition switch OFF)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Revision: 2012 March
2011 Murano CrossCabriolet
DEF-8
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
Monitor Item
Description
REAR DEF SW
This is displayed even when it is not equipped.
PUSH SW
Indicates [ON/OFF] condition of push switch.
Test Item
Description
REAR DEFOGGER
This test is able to check rear window defogger operation. Rear window defogger operates when
“ON” on CONSULT screen is touched.
Revision: 2012 March
2011 Murano CrossCabriolet
DIAGNOSIS SYSTEM (SOFT TOP CONTROL UNIT)
DEF-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
DIAGNOSIS SYSTEM (SOFT TOP CONTROL UNIT)
CONSULT Function
INFOID:0000000007258936
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with soft top control unit.
SELF-DIAG RESULT
.
Freeze Frame Data
The soft top control unit records the following vehicle condition at the time when the DTC is detected, and dis-
plays on CONSULT.
Diagnosis mode
Function Description
ECU Identification
The soft top control unit part number is displayed.
Self Diagnostic Result
Displays the diagnosis results judged by soft top control unit.
Freeze Frame Data
The soft top control unit records the vehicle condition at the time when
the DTC is detected, and displays.
Data Monitor
The soft top control unit input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from soft
top control unit.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from soft
top control unit.
CONSULT display
Description
ROOF SW (OPEN)
ON/OFF
OPEN input state of roof open/close switch is displayed.
ROOF SW (CLOSE)
ON/OFF
CLOSE input state of roof open/close switch is displayed.
ROOF LATCHED LH
ON/OFF
Input state of roof striker sensor LH is displayed.
ROOF LATCHED RH
ON/OFF
Input state of roof striker sensor RH is displayed.
F/CENTER LOCK
ON/OFF
Input state of roof latch lock sensor is displayed.
R/RAIL RAISED LH
ON/OFF
Input state of roof status sensor LH is displayed.
R/RAIL LOWERED
ON/OFF
Input state of roof status sensor LH is displayed.
5BOW LOWERED
ON/OFF
Input state of 5th bow status sensor LH is displayed.
5BOW RAISED
ON/OFF
Input state of 5th bow status sensor RH is displayed.
S/LID OPEN LH
ON/OFF
Input state of storage lid status sensor LH is displayed.
STORAGE LID CLOSE LH
ON/OFF
Input state of storage lid status sensor LH is displayed.
SWITCH VALVE 1
ON/OFF
Output state to switching valve 1 is displayed.
SWITCH VALVE 2
ON/OFF
Output state to switching valve 2 is displayed.
SWITCH VALVE 3
ON/OFF
Output state to switching valve 3 is displayed.
SWITCH VALVE 4
ON/OFF
Output state to switching valve 4 is displayed.
PUMP OUT (LH)
ON/OFF
Right rotation output state to hydraulic motor is displayed.
PUMP OUT (RH)
ON/OFF
Left rotation output state to hydraulic motor is displayed.
OUTSIDE FLAP DEPLOYMENT
ON/OFF
Input state of outside flap sensor (deployment switch) is displayed.
OUTSIDE FLAP STORAGE
ON/OFF
Input state of outside flap sensor (storage switch) is displayed.
INSIDE FLAP DEPLOYMENT
ON/OFF
Input state of inside flap sensor (deployment switch) is displayed.
INSIDE FLAP STORAGE
ON/OFF
Input state of inside flap sensor (storage switch) is displayed.
S/LID LOCK OPEN SW
ON/OFF
Input state of storage lid lock assembly (open switch) is displayed.
S/LID LOCK CLOSE SW
ON/OFF
Input state of storage lid lock assembly (close switch) is displayed.
S/LID LOCK HALF LATCH SW
ON/OFF
Input state of storage lid lock assembly (half latch switch) is displayed.
Revision: 2012 March
2011 Murano CrossCabriolet
DEF-10
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (SOFT TOP CONTROL UNIT)
DATA MONITOR
STORAGE LID DOOR SWITCH
ON/OFF
Input state of storage lid lock assembly (storage lid door switch) is displayed.
OUT FLAP MOTOR RELAY 1
ON/OFF
Input state of outside flap motor relay 1 is displayed.
OUT FLAP MOTOR RELAY 2
ON/OFF
Input state of outside flap motor relay 2 is displayed.
INSIDE FLAP MOTOR RELAY 1
ON/OFF
Input state of inside flap motor relay 1 is displayed.
INSIDE FLAP MOTOR RELAY 2
ON/OFF
Input state of inside flap motor relay 2 is displayed.
STORAGE LID LOCK RELAY 1
ON/OFF
Input state of storage lid lock relay 1 is displayed.
STORAGE LID LOCK RELAY 2
ON/OFF
Input state of storage lid lock relay 2 is displayed.
TONNEAU BOARD SWITCH
ON/OFF
Input state of tonneau board switch is displayed.
TRUNK LID OP/CL STATUS
OPEN/CLOSE
Input state of trunk lid lock assembly (trunk room lamp switch) is displayed.
CONSULT display
Description
CONSULT display
Description
ROOF LATCHED LH
ON/OFF/NG
Input state of roof striker sensor LH is displayed.
ROOF LATCHED RH
ON/OFF/NG
Input state of roof striker sensor RH is displayed.
F/CENTER LOCK
ON/OFF/NG
Input state of roof latch lock sensor is displayed.
R/RAIL RAISED LH
ON/OFF/NG
Input state of roof status sensor LH is displayed.
R/RAIL LOWERED
ON/OFF/NG
Input state of roof status sensor LH is displayed.
5TH BOW LOWERED
ON/OFF/NG
Input state of 5th bow status sensor LH is displayed.
5TH BOW RAISED
ON/OFF/NG
Input state of 5th bow status sensor RH is displayed.
S/LID OPEN LH
ON/OFF/NG
Input state of storage lid status sensor LH is displayed.
STORAGE LID CLOSE LH
ON/OFF/NG
Input state of storage lid status sensor LH is displayed.
SWITCHING VALVE 1
ON/OFF/NG
Output state to switching valve 1 is displayed.
SWITCHING VALVE 2
ON/OFF/NG
Output state to switching valve 2 is displayed.
SWITCHING VALVE 3
ON/OFF/NG
Output state to switching valve 3 is displayed.
SWITCHING VALVE 4
ON/OFF/NG
Output state to switching valve 4 is displayed.
PUMP OUT (RH)
ON/OFF/NG
Right rotation output state to hydraulic motor is displayed.
PUMP OUT (LH)
ON/OFF/NG
Left rotation output state to hydraulic motor is displayed.
OUTSIDE FLAP DEPLOYMENT
ON/OFF/NG
Input state of outside flap sensor (deployment switch) is displayed.
OUTSIDE FLAP STORAGE
ON/OFF/NG
Input state of outside flap sensor (storage switch) is displayed.
INSIDE FLAP DEPLOYMENT
ON/OFF/NG
Input state of inside flap sensor (deployment switch) is displayed.
INSIDE FLAP STORAGE
ON/OFF/NG
Input state of inside flap sensor (storage switch) is displayed.
S/LID LOCK OPEN SW
ON/OFF/NG
Input state of storage lid lock assembly (open switch) is displayed.
S/LID LOCK CLOSE SW
ON/OFF/NG
Input state of storage lid lock assembly (close switch) is displayed.
S/LID LOCK HALF LATCH SW
ON/OFF/NG
Input state of storage lid lock assembly (half latch switch) is displayed.
STORAGE LID DOOR SWITCH
ON/OFF/NG
Input state of storage lid lock assembly (storage lid door switch) is displayed.
OUT FLAP MOTOR RELAY 1
ON/OFF/NG
Input state of outside flap motor relay 1 is displayed.
OUT FLAP MOTOR RELAY 2
ON/OFF/NG
Input state of outside flap motor relay 2 is displayed.
INSIDE FLAP MOTOR RELAY 1
ON/OFF/NG
Input state of inside flap motor relay 1 is displayed.
INSIDE FLAP MOTOR RELAY 2
ON/OFF/NG
Input state of inside flap motor relay 2 is displayed.
STORAGE LID LOCK RELAY 1
ON/OFF/NG
Input state of storage lid lock relay 1 is displayed.
STORAGE LID LOCK RELAY 2
ON/OFF/NG
Input state of storage lid lock relay 2 is displayed.
ROOF SW (OPEN)
ON/OFF
OPEN input state of roof open/close switch is displayed.
ROOF SW (CLOSE)
ON/OFF
CLOSE input state of roof open/close switch is displayed.
SHIFT R SIGNAL
ON/OFF
Input state of shift position (R position) is displayed.
Revision: 2012 March
2011 Murano CrossCabriolet
DIAGNOSIS SYSTEM (SOFT TOP CONTROL UNIT)
DEF-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
ACTIVE TEST
TRUNK OPEN REQUEST SIG
ON/OFF
Input state of trunk open request signal from BCM is displayed.
TRUNK LID OP/CL STATUS
OPEN/CLOSE
Input state of trunk lid lock assembly (trunk room lamp switch) is displayed.
THER PROTEC PUMP
OK/NG
Non-operation state of thermo protection (hydraulic pump) is displayed.
THER PROTEC RCU
OK/NG
Non-operation state of thermo protection (soft top control unit) is displayed.
PWR COND RCU
OK/NG
Diagnosis result of power supply (soft top control unit) is displayed.
PWR COND P/W
OK/NG
Diagnosis result of power supply (front power window) is displayed.
PWR COND REAR P/W
OK/NG
Diagnosis result of power supply (rear power window) is displayed.
LOCAL COMM 1
NG/SLEEP/NG
State of serial link 1 is displayed.
LOCAL COMM 2
NG/SLEEP/NG
State of serial link 2 is displayed.
REAR DEF OUT
OK/NG
Output state to rear window defogger is displayed.
TONNEAU BOARD SWITCH
ON/OFF
Input state of tonneau board switch is displayed.
P/W OP REQ SW SIG
ON/OFF
Input state of power window open signal from request switch is displayed.
PROHIBIT P/W UP
ON/OFF
Output state to power window operation prohibition signal is displayed.
IGN ON SIG (BCM)
ON/OFF
Receiving state of ignition ON signal from BCM is displayed.
RF OP REQ SW SIG
ON/OFF
Input state of soft top open signal from request switch is displayed.
CONSULT display
Description
CONSULT display
Operation/condition
Description
Item
Indication
ROOF LATCHED LH/RH
LOCK
Soft top is fully closed posi-
tion.
Roof lock assembly performs lock operation.
UNLOCK
Roof lock assembly performs unlock operation.
STORAGE LID
OPEN
Storage lid is neutral posi-
tion.
Storage lid performs open operation.
CLOSE
Storage lid performs close operation.
SOFT TOP SYSTEM
UP
• Storage lid is fully open
position.
• Outside flap is fully
closed position.
Soft top performs closed operation.
DOWN
Soft top performs open operation.
ROOF SYSTEM
OPEN
—
Soft top system performs open operation.
CLOSE
Soft top system performs closed operation.
5TH BOW SYSTEM
OPEN
• Roof lock is unlock posi-
tion.
• Storage lid is fully closed
position.
1st bow and 5th bow performs fold operation.
CLOSE
1st bow and 5th bow performs spread operation.
HYDRAULIC PRESSURE
RELEASE
ON
—
Switching valve performs OFF operation.
CAUTION:
An unintentional operation of soft top or storage lid may
occur due to its own weight because oil pressure is not
maintained when switching valve is released.
To prevent injury, be careful not to pinch hands.
TRUNK OPENER
ON
Soft top is fully open/closed
position.
Trunk lid opener actuator performs unlock operation.
ROOF STATE OUTPUT
(AUDIO)
ON
Roof lock is unlock position.
Full open position signal of roof is transmitted to audio unit.
OFF
Full closed position signal of roof is transmitted to audio unit.
POWER WINDOW (LH/
RH)
UP
• Soft top is fully open/
closed position.
• Power window system is
initialized.
Power window (LH/RH) performs closed operation.
DOWN
Power window (LH/RH) performs open operation.
REAR WINDOW DEFOG-
GER
ON
Soft top is fully closed posi-
tion.
Rear window defogger performs ON operation.
OFF
Rear window defogger performs OFF operation.
Revision: 2012 March
2011 Murano CrossCabriolet
DEF-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (SOFT TOP CONTROL UNIT)
OUTSIDE FLAP MOTOR
DEPLOY
• Soft top is in the storage
room.
• Storage lid is fully open
position.
Outside flap motor performs deployment operation.
STORAGE
Outside flap motor performs storage operation.
INSIDE FLAP MOTOR
DEPLOY
Storage lid is fully open po-
sition.
Inside flap motor performs deployment operation.
STORAGE
Inside flap motor performs storage operation.
STORAGE LID CLOSURE
MOTOR
OP POS
Storage lid is fully closed
position.
Storage lid closure motor performs open operation.
CL POS
Storage lid closure motor performs closed operation.
NOTE:
Closure motor stops the closed operation and starts the neu-
tral operation after turning close switch ON.
CONSULT display
Operation/condition
Description
Item
Indication
Revision: 2012 March
2011 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст