Murano Cross Cabriolet Z51 (2011 year). Manual — part 60
STR-16
< REMOVAL AND INSTALLATION >
STARTER MOTOR
Type: M000TA0072
Removal and Installation
INFOID:0000000006939174
REMOVAL
1.
Remove the battery Refer to
PG-112, "Removal and Installation"
.
2.
Remove the air cleaner assembly and air ducts.
3.
Disconnect the following unit connectors:
• ECM
• TCM
• IPDM E/R
4.
Remove the battery tray.
5.
Disconnect the starter motor harness connectors.
6.
Remove the starter motor mounting bolts, using power tools.
7.
Remove the starter motor.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Be careful to tighten “B” terminal nut to the specified torque.
JPBIA1777GB
1.
Magnetic switch assembly
2.
Dust cover kit
3.
Gear case assembly
4.
Pinion assembly
5.
Stopper
6.
Ring
7.
Ring
8.
Stopper
9.
Yoke assembly
10. Armature assembly
11.
Brush holder assembly
12. Metal
13. Rear cover
14. Gear assembly
15. Shift lever set
16. Clutch gear assembly
17. Center bracket
18. Packing
19. Gear shaft
: N·m (kg-m, in-lb)
Revision: 2012 March
2011 Murano CrossCabriolet
STARTER MOTOR
STR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
Inspection
INFOID:0000000006939175
INSPECTION AFTER DISASSEMBLY
Pinion/Clutch Check
1.
Inspect pinion teeth.
• Replace pinion if teeth are worn or damaged. (Also check condition of ring gear teeth.)
2.
Inspect reduction gear teeth.
• Replace reduction gear if teeth are worn or damaged. (Also check condition of armature shaft gear
teeth.)
3.
Check to see if pinion locks in one direction and rotates smoothly in the opposite direction.
• If it locks or rotates in both directions, or unusual resistance is evident, replace.
Revision: 2012 March
2011 Murano CrossCabriolet
STR-18
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Starter Motor
INFOID:0000000006939176
Type
M000TA0072
MITSUBISHI make
Reduction gear type
System voltage
(V)
12
No-load
Terminal voltage
(V)
11
Current
(A)
Less than 90
Revolution
(rpm)
More than 2,400
Minimum diameter of commutator
[mm (in)]
28.0 (1.102)
Minimum length of brush
[mm (in)]
5.5 (0.217)
Brush spring tension
[N (kg, lb)]
15.0 - 20.4 (1.5 - 3.4)
Clearance between bearing metal and armature shaft
[mm (in)]
Less than 0.2 (0.008)
Clearance between pinion front edge and pinion stopper
[mm (in)]
0.5 - 2.0 (0.020 - 0.079)
Revision: 2012 March
2011 Murano CrossCabriolet
VTL-1
VENTILATION, HEATER & AIR CONDITIONER
C
D
E
F
G
H
J
K
L
M
SECTION
VTL
A
B
VTL
N
O
P
CONTENTS
VENTILATION SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
VENTILATION SYSTEM . . . . . . . . . .
System Description . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . .
DUCT AND GRILLE . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
CENTER VENTILATOR GRILLE . . . . . . . ....
CENTER VENTILATOR GRILLE : Removal and
Installation . . . . . . . . . . . . . . . .....
SIDE VENTILATOR GRILLE . . . . . . . . . ...
SIDE VENTILATOR GRILLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ....
SIDE DEFROSTER GRILLE . . . . . . . . . ...
SIDE DEFROSTER GRILLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ....
VENTILATOR DUCT . . . . . . . . . . . . ...
VENTILATOR DUCT : Removal and Installation . ..
UPPER VENTILATOR DUCT . . . . . . . . .
UPPER VENTILATOR DUCT : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
DEFROSTER NOZZLE AND SIDE DEFROSTER
NOZZLE . . . . . . . . . . . . . . . . . .
DEFROSTER NOZZLE AND SIDE DEFROSTER
NOZZLE : Removal and Installation . . . . . .
FRONT FOOT DUCT . . . . . . . . . . . . .
FRONT FOOT DUCT : Removal and Installation .
HEATER DUCT . . . . . . . . . . . . . . ..
HEATER DUCT : Removal and Installation . . . .
REAR FOOT DUCT 1 . . . . . . . . . . . .
REAR FOOT DUCT 1 : Removal and Installation .
REAR FOOT DUCT 2 . . . . . . . . . . . .
REAR FOOT DUCT 2 : Removal and Installation .
REAR FOOT DUCT 3 . . . . . . . . . . . .
REAR FOOT DUCT 3 : Removal and Installation .
REAR VENTILATOR DUCT 1 . . . . . . . . ...
REAR VENTILATOR DUCT 1 : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
REAR VENTILATOR DUCT 2 . . . . . . . . ...
REAR VENTILATOR DUCT 2 : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
REAR VENTILATOR DUCT 3 . . . . . . . . ...
REAR VENTILATOR DUCT 3 : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
REAR VENTILATOR GRILLE . . . . . . . . ...
REAR VENTILATOR GRILLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
BLOWER UNIT . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
BLOWER MOTOR . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
IN-CABIN MICROFILTER . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Revision: 2012 March
2011 Murano CrossCabriolet
VTL-2
Removal and Installation . . . . . . . . . ....
Replacement . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
In-cabin microfilter . . . . . . . . . . . . ...
Revision: 2012 March
2011 Murano CrossCabriolet
PRECAUTIONS
VTL-3
< PRECAUTION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007230834
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Revision: 2012 March
2011 Murano CrossCabriolet
VTL-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000007230835
Tool name
Description
Remover tool
Removes clips, pawls and metal clips
JMKIA3050ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
VENTILATION SYSTEM
VTL-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
SYSTEM DESCRIPTION
VENTILATION SYSTEM
System Description
INFOID:0000000007230836
SWITCH AND THEIR CONTROL FUNCTION
JPIIA0445GB
Revision: 2012 March
2011 Murano CrossCabriolet
VTL-6
< SYSTEM DESCRIPTION >
VENTILATION SYSTEM
*: Inlet status is displayed by indicator during activating automatic control
AIR DISTRIBUTION
Switch/Dial position
Door position
Mode door
In
ta
ke
do
or
Up
pe
r ve
nt
ila
to
r do
or
Air mix door
V
e
n
tila
to
r do
or
M
ax
. co
ol do
or
De
fros
te
r do
or
Fo
ot
do
or
(Driver side)
(Pa
sse
ng
er s
id
e
)
AUTO switch
AUTO
—
—
—
—
MODE switch
A
A
A
A
B
B
A
B
C
B
B
C
C
B
B
B
DEF switch
C
C
C
A
Intake switch
*
—
—
—
—
A
B
UPPER VENT switch
—
A – B
C
Temperature control
dial (Driver side)
DUAL
switch:
OFF
60
°
F
—
A
A
61
°
F – 89
°
F
AUTO
AUTO
90
°
F
B
B
DUAL
switch:
ON
60
°
F
A
—
61
°
F – 89
°
F
AUTO
90
°
F
B
Temperature control dial (Passen-
ger side)
60
°
F
—
A
61
°
F – 89
°
F
AUTO
90
°
F
B
ON·OFF switch
OFF
C
B
B
C
—
Discharge air flow
MODE/DEF
set position
Condition
Air outlet/distribution
Ventilator
Foot
Defroster
Front
Upper
Rear
Front
Rear
Center
Side
• DUAL
switch:
OFF
• UPPER
VENT
switch:
ON
40%
41%
8%
11%
—
—
—
18%
24%
10%
17%
23%
8%
—
—
12%
12%
15.5%
27.5%
12%
21%
—
11%
11%
14%
24%
11%
29%
—
11%
10.5%
12.5%
—
—
66%
Revision: 2012 March
2011 Murano CrossCabriolet
DUCT AND GRILLE
VTL-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
REMOVAL AND INSTALLATION
DUCT AND GRILLE
Exploded View
INFOID:0000000007230838
FRONT
REAR
1.
Defroster nozzle
2.
Side defroster nozzle LH
3.
Front foot duct LH
4.
Heater duct
5.
Heater & cooling unit assembly
6.
Ventilator duct
7.
Side defroster grille LH
8.
Instrument panel assembly
9.
Side ventilator grille LH
10. Center ventilator grille assembly
11. Side ventilator grille RH
12. Side defroster grille RH
13. Center speaker grille
14. Blower unit assembly
15. Front foot duct RH
16. Side defroster nozzle RH
17. Upper ventilator duct
JPIIA1225ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
VTL-8
< REMOVAL AND INSTALLATION >
DUCT AND GRILLE
CENTER VENTILATOR GRILLE
CENTER VENTILATOR GRILLE : Removal and Installation
INFOID:0000000007230839
REMOVAL
1.
Remove cluster lid A. Refer to
2.
Remove cluster lid D. Refer to
3.
Remove fixing screws (A).
4.
Pull out center ventilator grille assembly (1) toward instrument
panel assembly to remove.
INSTALLATION
1.
Heater & cooling unit assembly
2.
Rear foot duct 1 LH
3.
Rear foot duct 2 LH
4.
Rear foot duct 3 LH
5.
Rear ventilator duct 1
6.
Rear ventilator duct 2
7.
Rear ventilator duct 3
8.
Console rear finisher
9.
Rear ventilator grille
10.
Rear foot duct 3 RH
11.
Rear foot duct 2 RH
12. Rear foot duct 1 RH
: Clip
: Pawl
JMIIA1899ZZ
: Clip
: Pawl
JMJIA1325ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
DUCT AND GRILLE
VTL-9
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
Install in the reverse order of removal.
SIDE VENTILATOR GRILLE
SIDE VENTILATOR GRILLE : Removal and Installation
INFOID:0000000007230840
REMOVAL
1.
Remove instrument side finisher. Refer to
.
2.
Remove fixing screw (A).
3.
Disengage fixing metal clips using a remover tool (B), and then
remove side ventilator grille (1).
INSTALLATION
Install in the reverse order of removal.
SIDE DEFROSTER GRILLE
SIDE DEFROSTER GRILLE : Removal and Installation
INFOID:0000000007230841
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Remove defroster nozzle and side defroster nozzle. Refer to
VTL-10, "DEFROSTER NOZZLE AND SIDE
DEFROSTER NOZZLE : Removal and Installation"
.
3.
Remove fixing screws (A), and then remove side defroster grille
(1).
INSTALLATION
Install in the reverse order of removal.
VENTILATOR DUCT
VENTILATOR DUCT : Removal and Installation
INFOID:0000000007230842
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Remove defroster nozzle and side defroster nozzle. Refer to
VTL-10, "DEFROSTER NOZZLE AND SIDE
DEFROSTER NOZZLE : Removal and Installation"
.
: Metal clip
JPIIA0583ZZ
JPIIA0584ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
VTL-10
< REMOVAL AND INSTALLATION >
DUCT AND GRILLE
3.
Remove fixing screws (A), and then remove ventilator duct (1).
INSTALLATION
Install in the reverse order of removal.
UPPER VENTILATOR DUCT
UPPER VENTILATOR DUCT : Removal and Installation
INFOID:0000000007233014
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Remove defroster nozzle and side defroster nozzle. Refer to
VTL-10, "DEFROSTER NOZZLE AND SIDE
DEFROSTER NOZZLE : Removal and Installation"
3.
Remove fixing screws (A), and then remove upper ventilator
duct (1).
INSTALLATION
Install in the reverse order of removal.
DEFROSTER NOZZLE AND SIDE DEFROSTER NOZZLE
DEFROSTER NOZZLE AND SIDE DEFROSTER NOZZLE : Removal and Installation
INFOID:0000000007230843
REMOVAL
1.
Remove instrument panel assembly. Refer to
.
JPIIA0585ZZ
JPIIA0586ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
DUCT AND GRILLE
VTL-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
2.
Remove mounting screws (A), and then remove defroster nozzle (1), side defroster nozzle RH (2) and
side defroster nozzle LH (3) from instrument panel assembly as a set.
3.
Remove side defroster nozzle (LH and RH) from defroster nozzle.
INSTALLATION
Install in the reverse order of removal.
FRONT FOOT DUCT
FRONT FOOT DUCT : Removal and Installation
INFOID:0000000007230847
REMOVAL
Driver Side
1.
Remove instrument lower panel LH. Refer to
IP-13, "Removal and Installation"
2.
Remove fixing screws (A), and then remove front foot duct LH
(1).
Passenger Side
1.
Remove blower unit assembly. Refer to
VTL-18, "Removal and Installation"
.
2.
Remove fixing screws (A), and harness clip, and then remove
front foot duct RH (1).
INSTALLATION
Install in the reverse order of removal.
JPIIA0587ZZ
: Vehicle front
JPIIA1226ZZ
: Vehicle front
JPIIA1227ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
VTL-12
< REMOVAL AND INSTALLATION >
DUCT AND GRILLE
HEATER DUCT
HEATER DUCT : Removal and Installation
INFOID:0000000007257126
REMOVAL
1.
Remove instrument lower panel LH. Refer to
IP-13, "Removal and Installation"
.
2.
Remove fixing screw (A), and then remove heater duct (1).
INSTALLATION
Install in the reverse order of removal.
REAR FOOT DUCT 1
REAR FOOT DUCT 1 : Removal and Installation
INFOID:0000000007230845
REMOVAL
Driver Side
1.
Remove instrument lower cover LH. Refer to
IP-21, "Removal and Installation"
.
2.
Remove rear foot duct 1 LH (1).
Passenger Side
1.
Remove instrument lower cover RH. Refer to
IP-21, "Removal and Installation"
2.
Remove rear foot duct 1 RH (1).
INSTALLATION
Install in the reverse order of removal.
REAR FOOT DUCT 2
JPIIA0599ZZ
JPIIA0595ZZ
JPIIA0596ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
DUCT AND GRILLE
VTL-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
REAR FOOT DUCT 2 : Removal and Installation
INFOID:0000000007256339
REMOVAL
Driver Side
1.
Remove rear foot duct 1 LH. Refer to
VTL-12, "REAR FOOT DUCT 1 : Removal and Installation"
2.
Pull up driver side floor carpet of secure work space. Refer to
3.
Remove fixing clip (A), and then remove rear foot duct 2 LH (1).
Passenger Side
1.
Remove rear foot duct 1 RH. Refer to
VTL-12, "REAR FOOT DUCT 1 : Removal and Installation"
.
2.
Pull up passenger side floor carpet of secure work space. Refer to
.
3.
Remove fixing clip (A), and then remove rear foot duct 2 RH (1).
INSTALLATION
Install in the reverse order of removal.
REAR FOOT DUCT 3
REAR FOOT DUCT 3 : Removal and Installation
INFOID:0000000007256340
REMOVAL
Driver Side
1.
Remove rear foot duct 2 LH. Refer to
VTL-13, "REAR FOOT DUCT 2 : Removal and Installation"
2.
Remove fixing screw (A), and then remove rear foot duct 3 LH
(1).
Passenger Side
1.
Remove rear foot duct 2 LH. Refer to
VTL-13, "REAR FOOT DUCT 2 : Removal and Installation"
JPIIA0597ZZ
JPIIA0598ZZ
JPIIA0593ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст