Murano Cross Cabriolet Z51 (2011 year). Manual — part 31
QUARTER WINDOW GLASS
GW-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Fitting between door glass and quarter window glass
1.
Fully close door glass and quarter window glass.
2.
Check that both upper edges of door glass and quarter window glass are the same level.
3.
Check that the clearance between door glass and quarter window glass is in the range of E.
4.
Check that the clearances between the weather-strip and quarter window glass is in the range of C and D.
Fitting inspection
• Check that the overlap length with the body side weather-strip is maintained on the glass.
• Check that clearance between door glass and quarter window glass sash is parallel when door glass is
closed.
• Adjust sub channel and set quarter window glass to the normal position, when clearance between front door
glass and quarter sash is not parallel. At this time, adjustment for stopper of panel side is necessary again.
• When adjusting fitting of glass, open glass once, fully close it, and then check the fitting while glass is fully
closed.
• Check opening and closing trace of quarter window glass.
• Check that closing trace of quarter window glass is constant just before glass is fully closed while soft top is
open.
• Open and close quarter window glass and check that operation is normal, for each condition where soft top
is open or closed, or door glass is open or closed.
JMKIA8394ZZ
1.
Door glass assembly
2.
Quarter window glass
C
: 9.8 (0.386)
D
: 10.6 (0.417)
E
: 8.5 (0.335)
Unit: mm (in)
Revision: 2012 March
2011 Murano CrossCabriolet
GW-24
< REMOVAL AND INSTALLATION >
QUARTER WINDOW GLASS
• Particularly, check that door glass does not contact to quarter sash when quarter window glass is operated
to the fully closed position while soft top is open status and front door glass is closed.
Water Leakage Test
Visually check for water leakage after adjustment. Refer to
.
Revision: 2012 March
2011 Murano CrossCabriolet
DOOR GLASS
GW-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
DOOR GLASS
Exploded View
INFOID:0000000007220782
Removal and Installation
INFOID:0000000007220783
REMOVAL
1.
Remove door finisher. Refer to
INT-13, "Removal and Installation"
2.
Remove door finisher inside seal.
3.
Remove door module assembly hole cover seal.
1. Door panel assembly
2.
Door glass
3.
Module base
4.
Hole cover seal
5.
Power window motor
6.
Door regulator
7.
Door corner piece weather-strip up-
per
8.
Door corner piece weather-strip low-
er
9.
Door corner piece assembly
10. Door inside seal
: Vehicle front
JMKIA8390ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
GW-26
< REMOVAL AND INSTALLATION >
DOOR GLASS
4.
Operate the power window main switch to raise or lower the
door window until the glass mounting bolts can be seen.
5.
Remove door glass mounting bolts (A).
6.
Remove the door glass.
CAUTION:
When removing or installing, 2 workers are required because of the weight of the glass and for
safety reasons.
a.
Hold securely the door glass.
b.
Rotate slightly the door glass
c.
Pull up the door glass out to remove.
7.
Remove the corner piece assembly.
a.
Remove door mirror assembly. Refer to
MIR-26, "DOOR MIRROR ASSEMBLY : Removal and Installa-
b.
Remove corner piece assembly mounting bolts and nut.
c.
Pull up while rotating corner piece assembly to remove out of the door panel.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000007220784
SYSTEM INITIALIZATION
• Description: Refer to
.
• Work procedure: Refer to
CHECK ANTI-PINCH FUNCTION
• Description: Refer to
.
• Work procedure: Refer to
FITTING INSPECTION
JMKIA8392ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
DOOR GLASS
GW-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Preparation for adjustment
1.
Apply protective tape (A) as shown on the figure above on door glass and quarter window glass.
2.
Fully close door window glass and quarter window glass, and mark each edge of weather-strip on the
glass as shown by the marks (B).
3.
Measure the clearances (C), (D), and (E) and check that these clearances are in the range provided in the
figure above. If not, then proceed to the adjustment of quarter window glass by following the steps below.
JMKIA8395ZZ
1.
Door glass assembly
2.
Quarter window glass
C:
4.0 (0.157)
D:
9.8 (0.386)
E:
9.8 (0.386)
Unit: mm (in)
Revision: 2012 March
2011 Murano CrossCabriolet
GW-28
< REMOVAL AND INSTALLATION >
DOOR GLASS
Fitting between door glass and corner piece assembly
1.
Remove the door glass. Refer to
GW-25, "Removal and Installation"
.
2.
Apply protective tape (B) on door glass at a distance of 25.5 mm (0.1004in), starting from front edge as
shown in the figure above.
JMKIA8393ZZ
1.
Door glass
2.
Mirror base
3.
Quarter window glass
4.
Door weather -strip
F
: 25.5 (1.0004)
G
: 4 (0.157)
H
: 6.6 (0.260)
I
: 9.8 (0.386)
J
: 9.1 (0.358)
K
: 8.5 (0.335)
L
: 2 (0.079)
M
: 2 (0.079)
Unit: mm (in)
Revision: 2012 March
2011 Murano CrossCabriolet
DOOR GLASS
GW-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
3.
Reinstall door glass while fitting the corner piece assembly to the protective tape as shown in the figure
above.
Fitting between door glass and quarter window glass
1.
Fully close door glass and quarter window glass.
2.
Check that both upper edges of door glass and quarter window glass are at the same level.
3.
Check that the distance between door glass and quarter window glass sash is 8.5 mm (0.335 in).
Inclination Adjustment
• Check that door glass is fitted securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)] and check that the clearance to the
body side weather-strip is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass
and guide rail mounting bolts to correct the glass position if the clearance between door glass and body side
weather-strip is not parallel.
• Raise door glass fully and adjust door glass top end and body side weather-strip with adjusting bolt (B), (C),
or (D) as shown in the figure above.
• Always start at adjusting with bolt (B). If the desired angle is not achieved, then proceed to adjusting bolt (C)
and (D) respectively.
• Turn the adjusting bolt clockwise to move the door glass upper end outward.
• Turn the adjusting bolt counterclockwise to move the door glass upper end inward.
• Adjustment process with adjusting bolt (C) is the inverse of adjusting bolt (B) and (D).
• When adjusting with adjusting bolt (D), turn the adjusting bolt clockwise to move the door glass upper end
inward, then counterclockwise to move the door glass upper end outward.
JMKIA8598ZZ
1.
Door glass assembly
2.
Quarter window glass sash
3.
Quarter window glass
B
: 8.5 (0.335)
Unit: mm (in)
JMKIA8396ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
GW-30
< REMOVAL AND INSTALLATION >
DOOR REGULATOR
DOOR REGULATOR
Exploded View
INFOID:0000000007258556
Removal and Installation
INFOID:0000000007220786
REMOVAL
1.
Remove the door glass. Refer to
GW-25, "Removal and Installation"
.
2.
Disconnect the power window motor harness connector.
3.
Disconnect the harness fixing clips from the door module assembly.
1. Door panel assembly
2.
Door glass
3.
Module base
4.
Hole cover seal
5.
Power window motor
6.
Door regulator
7.
Door corner piece weather-strip up-
per
8.
Door corner piece weather-strip low-
er
9.
Door corner piece assembly
10. Door inside seal
: Vehicle front
JMKIA8390ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
DOOR REGULATOR
GW-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
4.
Remove door module assembly mounting bolts (A) and then
remove the door module assembly from door panel.
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000007220787
DISASSEMBLY
1.
Remove the power window motor from the module assembly.
2.
Remove door regulator assembly from module assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
Inspection After Removal
INFOID:0000000007220788
Check the regulator assembly for the following items. Replace or
grease it if a malfunction is detected.
• Wire wear
• Regulator deformation
Inspection and Adjustment
INFOID:0000000007258557
SYSTEM INITIALIZATION
• Description: Refer to
.
• Work procedure: Refer to
CHECK ANTI-PINCH FUNCTION
• Description: Refer to
.
• Work procedure: Refer to
FITTING INSPECTION
JMKIA8563ZZ
Glass mounting nut
Tightening torque
: 5.1N.m (0.52kg-m, 45 in-lb)
JMKIA8391ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
GW-32
< REMOVAL AND INSTALLATION >
DOOR REGULATOR
Preparation for adjustment
1.
Apply protective tape (A) as shown on the figure above on door glass and quarter window glass.
2.
Fully close door window glass and quarter window glass, and mark each edge of weather-strip on the
glass as shown by the marks (B).
3.
Measure the clearances (C), (D), and (E) and check that these clearances are in the range provided in the
figure above. If not, then proceed to the adjustment of quarter window glass by following the steps below.
JMKIA8395ZZ
1.
Door glass assembly
2.
Quarter window glass
C:
4.0 (0.157)
D:
9.8 (0.386)
E:
9.8 (0.386)
Unit: mm (in)
Revision: 2012 March
2011 Murano CrossCabriolet
DOOR REGULATOR
GW-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Fitting between door glass and corner piece assembly
1.
Remove the door glass. Refer to
GW-25, "Removal and Installation"
.
2.
Apply protective tape (B) on door glass at a distance of 25.5 mm (0.1004in), starting from front edge as
shown in the figure above.
JMKIA8393ZZ
1.
Door glass
2.
Mirror base
3.
Quarter window glass
4.
Door weather -strip
F
: 25.5 (1.0004)
G
: 4 (0.157)
H
: 6.6 (0.260)
I
: 9.8 (0.386)
J
: 9.1 (0.358)
K
: 8.5 (0.335)
L
: 2 (0.079)
M
: 2 (0.079)
Unit: mm (in)
Revision: 2012 March
2011 Murano CrossCabriolet
GW-34
< REMOVAL AND INSTALLATION >
DOOR REGULATOR
3.
Reinstall door glass while fitting the corner piece assembly to the protective tape as shown in the figure
above.
Fitting between door glass and quarter window glass
1.
Fully close door glass and quarter window glass.
2.
Check that both upper edges of door glass and quarter window glass are at the same level.
3.
Check that the distance between door glass and quarter window glass sash is 8.5 mm (0.335 in).
Inclination Adjustment
• Check that door glass is fitted securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)] and check that the clearance to the
body side weather-strip is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass
and guide rail mounting bolts to correct the glass position if the clearance between door glass and body side
weather-strip is not parallel.
• Raise door glass fully and adjust door glass top end and body side weather-strip with adjusting bolt (B), (C),
or (D) as shown in the figure above.
• Always start at adjusting with bolt (B). If the desired angle is not achieved, then proceed to adjusting bolt (C)
and (D) respectively.
• Turn the adjusting bolt clockwise to move the door glass upper end outward.
• Turn the adjusting bolt counterclockwise to move the door glass upper end inward.
• Adjustment process with adjusting bolt (C) is the inverse of adjusting bolt (B) and (D).
• When adjusting with adjusting bolt (D), turn the adjusting bolt clockwise to move the door glass upper end
inward, then counterclockwise to move the door glass upper end outward.
JMKIA8598ZZ
1.
Door glass assembly
2.
Quarter window glass sash
3.
Quarter window glass
B
: 8.5 (0.335)
Unit: mm (in)
JMKIA8396ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
HRN-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
HRN
A
B
HRN
N
O
P
CONTENTS
HORN
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ...
HORN . . . . . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
HORN . . . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Revision: 2012 March
2011 Murano CrossCabriolet
HRN-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000007236252
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Revision: 2012 March
2011 Murano CrossCabriolet
HORN
HRN-3
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
HRN
N
O
P
WIRING DIAGRAM
HORN
Wiring Diagram
INFOID:0000000006937867
JCLWA5340GB
Revision: 2012 March
2011 Murano CrossCabriolet
HRN-4
< WIRING DIAGRAM >
HORN
JCLWA5341GB
Revision: 2012 March
2011 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст