Murano Cross Cabriolet Z51 (2011 year). Manual — part 43
PCS
B2615 BLOWER RELAY CIRCUIT
PCS-63
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
2.
Check continuity between fuse block (J/B) harness connector and BCM harness connector.
3.
Check continuity between fuse block (J/B) harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> Repair or replace harness.
4.
CHECK BLOWER RELAY GROUND CIRCUIT
Check continuity between blower relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair blower relay ground circuit.
5.
CHECK BLOWER RELAY POWER SUPPLY CIRCUIT-2
1.
Install blower relay.
2.
Turn ignition switch ON.
3.
Check voltage between blower relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
CHECK BLOWER RELAY
PCS-63, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace fuse block (J/B).
NO
>> Replace blower relay.
7.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000006939110
1.
CHECK BLOWER RELAY
1.
Turn ignition switch OFF.
2.
Remove blower relay.
Fuse block (J/B)
BCM
Continuity
Connector
Terminal
Connector
Terminal
E103
6F
M122
102
Existed
Fuse block (J/B)
Ground
Continuity
Connector
Terminal
E103
6F
Not existed
Blower relay
Ground
Continuity
Terminal
2
Existed
(+)
(–)
Voltage (V)
(Approx.)
Blower relay
Terminal
5
Ground
Battery voltage
Revision: 2012 March
2011 Murano CrossCabriolet
PCS-64
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B2615 BLOWER RELAY CIRCUIT
3.
Check the continuity between blower relay terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace blower relay.
Terminals
Condition
Continuity
3 and 5
12 V direct current supply between terminals 1 and 2
Existed
No current supply
Not existed
PBIB0098E
Revision: 2012 March
2011 Murano CrossCabriolet
PCS
B2616 IGNITION RELAY CIRCUIT
PCS-65
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B2616 IGNITION RELAY CIRCUIT
DTC Logic
INFOID:0000000006939112
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions, and wait for at least 1 second.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006939113
1.
CHECK IGNITION RELAY POWER SUPPLY-1
1.
Turn ignition switch OFF.
2.
Remove ignition relay.
3.
Check voltage between ignition relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK IGNITION RELAY POWER SUPPLY-2
1.
Disconnect fuse block (J/B) connector.
2.
Check voltage between fuse block (J/B) harness connector and ground.
Is the inspection result normal?
YES
>> Replace fuse block (J/B).
NO
>> GO TO 3.
3.
CHECK IGNITION RELAY POWER SUPPLY CIRCUIT-1
1.
Disconnect BCM connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2616
BCM
An immediate operation of ignition relay (fuse
block) is requested by BCM, but there is no re-
sponse for more than 1 second
• Harness or connectors
(Ignition relay circuit is open or
shorted)
• Ignition relay (fuse block)
(+)
(–)
Condition
Voltage (V)
(Approx.)
Ignition relay
Terminal
1
Ground
Ignition switch
OFF or ACC
0
ON
Battery voltage
(+)
(–)
Condition
Voltage (V)
(Approx.)
Fuse block (J/B)
Connector
Terminal
M3
6C
Ground
Ignition switch
OFF or ACC
0
ON
Battery voltage
Revision: 2012 March
2011 Murano CrossCabriolet
PCS-66
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B2616 IGNITION RELAY CIRCUIT
2.
Check continuity between fuse block (J/B) harness connector and BCM harness connector.
3.
Check continuity between fuse block (J/B) harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
.
NO
>> Repair or replace harness.
4.
CHECK IGNITION RELAY GROUND CIRCUIT
Check continuity between ignition relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair ignition relay ground circuit.
5.
CHECK IGNITION RELAY POWER SUPPLY CIRCUIT-2
1.
Install ignition relay.
2.
Turn ignition switch ON.
3.
Check voltage between ignition relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
CHECK IGNITION RELAY
PCS-66, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace fuse block (J/B).
NO
>> Replace ignition relay.
7.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000006939114
1.
CHECK IGNITION RELAY
1.
Turn ignition switch OFF.
2.
Remove ignition relay.
Fuse block (J/B)
BCM
Continuity
Connector
Terminal
Connector
Terminal
M3
6C
M122
82
Existed
Fuse block (J/B)
Ground
Continuity
Connector
Terminal
M3
6C
Not existed
Ignition relay
Ground
Continuity
Terminal
2
Existed
(+)
(–)
Voltage (V)
(Approx.)
Ignition relay
Terminal
5
Ground
Battery voltage
Revision: 2012 March
2011 Murano CrossCabriolet
PCS
B2616 IGNITION RELAY CIRCUIT
PCS-67
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
3.
Check the continuity between ignition relay terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace Ignition relay.
Terminals
Condition
Continuity
3 and 5
12 V direct current supply between terminals 1 and 2
Existed
No current supply
Not existed
PBIB0098E
Revision: 2012 March
2011 Murano CrossCabriolet
PCS-68
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
B2618 BCM
B2618 BCM
DTC Logic
INFOID:0000000006939116
DTC DETECTION LOGIC
NOTE:
• If DTC B2618 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2618 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON under the following conditions, and wait for at least 1 second.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006939117
1.
INSPECTION START
1.
Turn ignition switch ON.
2.
Select “Self diagnostic result” mode with CONSULT.
3.
Touch “ERASE”.
4.
Perform DTC Confirmation Procedure.
See
.
Is the 1st trip DTC B2618 displayed again?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> INSPECTION END
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2618
BCM
An immediate operation of ignition relay (IPDM E/
R) is requested by BCM, but there is no response
for more than 1 second
BCM
Revision: 2012 March
2011 Murano CrossCabriolet
PCS
B261A PUSH-BUTTON IGNITION SWITCH
PCS-69
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
B261A PUSH-BUTTON IGNITION SWITCH
DTC Logic
INFOID:0000000006939119
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press the push-button ignition switch under the following conditions, and wait for at least 1 second.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006939120
1.
CHECK IGNITION SWITCH OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector and IPDM E/R connector.
3.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace IPDM E/R. Refer to
PCS-32, "Removal and Installation"
.
2.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between IPDM E/R harness connector and BCM harness connector.
3.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> Repair or replace harness.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B261A
PUSH-BUTTON IG-
NITION SWITCH
BCM detects a difference of signal for 1 second or
more between the following information.
• Power supply position by push-button ignition
switch
• Power supply position from IPDM E/R (CAN)
Harness or connectors
(Push-button ignition switch circuit is
open or shorted.)
(+)
(–)
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E10
28
Ground
Battery voltage
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
E10
28
M121
60
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E10
28
Not existed
Revision: 2012 March
2011 Murano CrossCabriolet
PCS-70
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH
PUSH-BUTTON IGNITION SWITCH
Component Function Check
INFOID:0000000006939123
1.
CHECK FUNCTION
1.
Select “PUSH SW” in “Data Monitor” mode with CONSULT.
2.
Check the push-button ignition switch signal under the following condition.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Go to
.
Diagnosis Procedure
INFOID:0000000006939124
1.
CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector and IPDM E/R connector.
3.
Check voltage between push-button ignition switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and push-button ignition switch harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK PUSH-BUTTON IGNITION SWITCH GROUND CIRCUIT
Check continuity between push-button ignition switch harness connector and ground.
Test item
Condition
Status
PUSH SW
Push-button ignition switch is pressed
ON
Push-button ignition switch is not pressed
OFF
(+)
(–)
Voltage (V)
(Approx.)
Push-button ignition switch
Connector
Terminal
M101
4
Ground
Battery voltage
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M121
60
M101
4
Existed
BCM
Ground
Continuity
Connector
Terminal
M121
60
Not existed
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M101
1
Existed
Revision: 2012 March
2011 Murano CrossCabriolet
PCS
PUSH-BUTTON IGNITION SWITCH
PCS-71
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK PUSH-BUTTON IGNITION SWITCH
PCS-71, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace push-button ignition switch.
5.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000006939125
1.
CHECK PUSH-BUTTON IGNITION SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector.
3.
Check continuity between push-button ignition switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace push-button ignition switch.
Push-button ignition switch
Condition
Continuity
Terminal
1
4
Push-button ignition
switch
Pressed
Existed
Not pressed
Not existed
Revision: 2012 March
2011 Murano CrossCabriolet
PCS-72
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
Description
INFOID:0000000006939126
The switch that changes the power supply position.
BCM maintains the power supply position status.
BCM changes the power supply position with the operation of the push-button ignition switch.
Component Function Check
INFOID:0000000007235612
1.
CHECK FUNCTION
Check push-button ignition switch (“LOCK INDICATOR”, “ACC INDICATOR” and “IGNITION ON IND”) in
Active Test Mode with CONSULT.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000007235613
1.
CHECK PUSH-BUTTON IGNITION SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect push-button ignition switch connector.
3.
Check voltage between push-button ignition switch harness connector and ground.
Is the inspection normal?
YES
>> GO TO 2.
NO-1
>> Check 10 A fuse [No.9, located in fuse block (J/B)].
NO-2
>> Check harness for open or short between push-button ignition switch and fuse.
2.
CHECK BCM INPUT
1.
Connect push-button ignition switch connector.
2.
Disconnect BCM connector.
3.
Check voltage between BCM connector and ground.
Is the inspection normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT
1.
Disconnect push-button ignition switch connector.
Test item
Description
LOCK INDICATOR
ACC INDICATOR
IGNITION ON IND
ON
Position indicator
Illuminate
OFF
Not illuminate
(+)
(–)
Voltage (V)
(Approx.)
Push-button ignition switch
Connector
Terminal
M101
9
Ground
Battery voltage
(+)
(–)
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M119
15
Ground
Battery voltage
M122
93
M123
134
Revision: 2012 March
2011 Murano CrossCabriolet
PCS
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR
PCS-73
< DTC/CIRCUIT DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
2.
Check continuity between BCM harness connector and push-button ignition switch harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection normal?
YES
>> Replace push-button ignition switch.
NO
>> Repair or replace harness.
Indicator
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
LOCK
M123
134
M101
5
Existed
ACC
M119
15
6
ON
M122
93
7
Indicator
BCM
Ground
Continuity
Connector
Terminal
LOCK
M123
134
Not existed
ACC
M119
15
ON
M122
93
Revision: 2012 March
2011 Murano CrossCabriolet
PCS-74
< SYMPTOM DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
PUSH-BUTTON IGNITION SWITCH DOES NOT OPERATE
SYMPTOM DIAGNOSIS
PUSH-BUTTON IGNITION SWITCH DOES NOT OPERATE
Description
INFOID:0000000006939137
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
NOTE:
The engine start function, door lock function, power distribution system, and NATS-IVIS/NVIS in the Intelligent
Key system are closely related to each other regarding control. The vehicle security function can operate only
when the door lock and power distribution system are operating normally.
Conditions of Vehicle (Operating Conditions)
• “ENGINE START BY I-KEY” in “WORK SUPPORT” is ON when setting on CONSULT.
• Intelligent Key is not inserted in key slot.
• One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.
Diagnosis Procedure
INFOID:0000000006939138
1.
PERFORM WORK SUPPORT
Perform “INSIDE ANT DIAGNOSIS” on Work Support of “INTELLIGENT KEY”.
Refer to
DLK-35, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSTIC RESULT
Perform Self-Diagnostic Result of “BCM”.
Is DTC detected?
YES
>> Refer to
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH
Check push-button ignition switch.
Refer to
PCS-70, "Component Function Check"
Is the operation normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2012 March
2011 Murano CrossCabriolet
PCS
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR DOES NOT ILLUMI-
NATE
PCS-75
< SYMPTOM DIAGNOSIS >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PUSH-BUTTON IGNITION SWITCH POSITION INDICATOR DOES NOT IL-
LUMINATE
Description
INFOID:0000000006939139
• Before performing the diagnosis in the following table, check “Work Flow”. Refer to
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
Conditions of Vehicle (Operating Conditions)
• “ENGINE START BY I-KEY” in “WORK SUPPORT” is ON when setting on CONSULT.
• One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.
Diagnosis Procedure
INFOID:0000000006939140
1.
CHECK PUSH-BUTTON IGNITION SWITCH INDICATOR
Check push-button ignition switch indicator.
Refer to
PCS-72, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2012 March
2011 Murano CrossCabriolet
PCS-76
< REMOVAL AND INSTALLATION >
[POWER DISTRIBUTION SYSTEM]
PUSH BUTTON IGNITION SWITCH
REMOVAL AND INSTALLATION
PUSH BUTTON IGNITION SWITCH
Exploded View
INFOID:0000000006939141
Removal and Installation
INFOID:0000000006939142
REMOVAL
1.
Remove the instrument stay cover LH. Refer to
IP-13, "Removal and Installation"
2.
Remove the push-button ignition switch (1) from instrument stay
cover LH, after removing pawl (A). Press push-button ignition
switch (1) back to disengage from instrument stay cover LH (2).
INSTALLATION
Install in the reverse order of removal.
1.
Push-button ignition switch
JMKIA1812ZZ
JMKIA1813ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
PWC-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
PWC
A
B
PWC
N
O
P
CONTENTS
POWER WINDOW CONTROL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . .....
Precaution for Battery Service . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . .....
SYSTEM . . . . . . . . . . . . . . . ..
System Diagram . . . . . . . . . . . . . ...
System Description . . . . . . . . . . . . ...
Fail-safe . . . . . . . . . . . . . . . . ....
DIAGNOSIS SYSTEM (BCM) . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
RETAINED PWR . . . . . . . . . . . . . ...
RETAINED PWR : CONSULT Function (BCM -
RETAINED PWR) . . . . . . . . . . . . ...
ECU DIAGNOSIS INFORMATION . . . ..
BCM, SOFT TOP CONTROL UNIT . . . . .
List of ECU Reference . . . . . . . . . . .
POWER WINDOW MAIN SWITCH . . . . .
Reference Value . . . . . . . . . . . . . .
Fail-safe . . . . . . . . . . . . . . . . ..
FRONT POWER WINDOW SWITCH (PAS-
SENGER SIDE) . . . . . . . . . . . . ..
Reference Value . . . . . . . . . . . . . .
Fail-safe . . . . . . . . . . . . . . . . ...
REAR POWER WINDOW SWITCH LH . . .
Reference Value . . . . . . . . . . . . . ..
Fail-safe . . . . . . . . . . . . . . . . ...
REAR POWER WINDOW SWITCH RH . . .
Reference Value . . . . . . . . . . . . . ..
Fail-safe . . . . . . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ..
POWER WINDOW SYSTEM . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
ADDITIONAL SERVICE WHEN REPLACING
POWER WINDOW SWITCH . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
SYSTEM INITIALIZATION . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
CHECK ANTI-PINCH FUNCTION . . . . . .
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
POWER SUPPLY AND GROUND CIRCUIT .
POWER WINDOW MAIN SWITCH . . . . . . .
Revision: 2012 March
2011 Murano CrossCabriolet
PWC-2
POWER WINDOW MAIN SWITCH : Diagnosis
Procedure . . . . . . . . . . . . . . . ...
FRONT POWER WINDOW SWITCH (PASSEN-
GER SIDE) . . . . . . . . . . . . . . . ....
FRONT POWER WINDOW SWITCH (PASSEN-
GER SIDE) : Diagnosis Procedure . . . . . . .
REAR POWER WINDOW SWITCH . . . . . . ..
REAR POWER WINDOW SWITCH : Diagnosis
Procedure . . . . . . . . . . . . . . . ...
POWER WINDOW MOTOR . . . . . . . ...
DRIVER SIDE . . . . . . . . . . . . . . ....
DRIVER SIDE : Component Function Check . . .
DRIVER SIDE : Diagnosis Procedure . . . . ....
PASSENGER SIDE . . . . . . . . . . . . ...
PASSENGER SIDE : Component Function Check
...
PASSENGER SIDE : Diagnosis Procedure . . ...
REAR LH . . . . . . . . . . . . . . . . ...
REAR LH : Component Function Check . . . ....
REAR LH : Diagnosis Procedure . . . . . . ....
REAR RH . . . . . . . . . . . . . . . . ..
REAR RH : Component Function Check . . . ....
REAR RH : Diagnosis Procedure . . . . . . ...
ENCODER CIRCUIT . . . . . . . . . . ..
DRIVER SIDE . . . . . . . . . . . . . . ....
DRIVER SIDE : Component Function Check . . .
DRIVER SIDE : Diagnosis Procedure . . . . ....
PASSENGER SIDE . . . . . . . . . . . . ...
PASSENGER SIDE : Component Function Check
...
PASSENGER SIDE : Diagnosis Procedure . . ...
REAR LH . . . . . . . . . . . . . . . . ...
REAR LH : Component Function Check . . . ....
REAR LH : Diagnosis Procedure . . . . . . ....
REAR RH . . . . . . . . . . . . . . . . ..
REAR RH : Component Function Check . . . ....
REAR RH : Diagnosis Procedure . . . . . . ...
DOOR KEY CYLINDER SWITCH . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
POWER WINDOW SERIAL LINK . . . . . .
POWER WINDOW MAIN SWITCH . . . . . . ...
POWER WINDOW MAIN SWITCH : Diagnosis
Procedure . . . . . . . . . . . . . . . ...
FRONT POWER WINDOW SWITCH (PASSEN-
GER SIDE) . . . . . . . . . . . . . . . ....
FRONT POWER WINDOW SWITCH (PASSEN-
GER SIDE) : Diagnosis Procedure . . . . . . .
REAR POWER WINDOW SWITCH LH . . . . . .
REAR POWER WINDOW SWITCH LH : Diagno-
sis Procedure . . . . . . . . . . . . . . ..
REAR POWER WINDOW SWITCH RH . . . . .
REAR POWER WINDOW SWITCH RH : Diagno-
sis Procedure . . . . . . . . . . . . . . ..
DOOR SWITCH . . . . . . . . . . . . .
DRIVER SIDE . . . . . . . . . . . . . . .
DRIVER SIDE : Component Function Check . . .
DRIVER SIDE : Diagnosis Procedure . . . . . .
PASSENGER SIDE . . . . . . . . . . . . ...
PASSENGER SIDE : Component Function Check
...
PASSENGER SIDE : Diagnosis Procedure . . .
SYMPTOM DIAGNOSIS . . . . . . .
NONE OF THE POWER WINDOWS CAN BE
OPERATED USING ANY SWITCH . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
DRIVER SIDE POWER WINDOW DOES NOT
OPERATE . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
FRONT PASSENGER SIDE POWER WIN-
DOW DOES NOT OPERATE . . . . . . .
WHEN FRONT POWER WINDOW SWITCH (PAS-
SENGER SIDE) IS OPERATED . . . . . . . .
WHEN POWER WINDOW MAIN SWITCH IS OP-
ERATED . . . . . . . . . . . . . . . . .
WHEN POWER WINDOW MAIN SWITCH IS OP-
ERATED : Diagnosis Procedure . . . . . . . .
REAR LH SIDE POWER WINDOW DOES
NOT OPERATE . . . . . . . . . . . . .
Revision: 2012 March
2011 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст