Murano Cross Cabriolet Z51 (2011 year). Manual — part 64
WCS-40
< SYMPTOM DIAGNOSIS >
THE KEY WARNING DOES NOT SOUND
THE KEY WARNING DOES NOT SOUND
Description
INFOID:0000000006940131
The is key warning chime does not sound under the following conditions.
• Key inserted into the key slot. (Key slot switch ON)
• Ignition switch is not in ON or START. (Ignition switch signal OFF)
• Front door switch (driver side) is open. [Door switch signal (driver side) ON]
Diagnosis Procedure
INFOID:0000000006940132
1.
CHECK BCM INPUT SIGNAL
1.
Connect CONSULT.
2.
Select the “Data Monitor” of “BCM (BUZZER)” and check the “KEY SW-SLOT” monitor value. Refer to
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK KEY SLOT SWITCH SIGNAL CIRCUIT
Check the key slot switch signal circuit. Refer to
DLK-119, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check applicable parts, and repair or replace corresponding parts.
3.
CHECK DOOR SWITCH SIGNAL (DRIVER SIDE) CIRCUIT
Check the door switch signal (driver side) circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Check the front door switch (driver side). Refer to
DLK-84, "Component Inspection"
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> Replace front door switch (driver side). Refer to
DLK-198, "Removal and Installation"
.
Revision: 2012 March
2011 Murano CrossCabriolet
WT-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
WT
A
B
WT
N
O
P
CONTENTS
ROAD WHEELS & TIRES
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Battery Service . . . . . . . . ..
Service Procedure Precautions for Models with a
Pop-up Roll Bar . . . . . . . . . . . . . .....
Service Notice and Precautions for TPMS . . . ....
Service Notice and Precautions for Road Wheel ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . .....
BCM . . . . . . . . . . . . . . . . . . ..
Tire Pressure Sensor . . . . . . . . . . . ....
Tire Pressure Receiver . . . . . . . . . . .....
Information Display . . . . . . . . . . . . ...
TPMS . . . . . . . . . . . . . . . . ...
System Description . . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (BCM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
AIR PRESSURE MONITOR . . . . . . . . . ..
AIR PRESSURE MONITOR : CONSULT Function
(BCM - AIR PRESSURE MONITOR) . . . . . ..
ECU DIAGNOSIS INFORMATION . . . ..
BCM . . . . . . . . . . . . . . . . ...
List of ECU Reference . . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
TIRE PRESSURE MONITORING SYSTEM . ..
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
BCM . . . . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
TIRE PRESSURE SENSOR WAKE UP OP-
ERATION . . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
ID REGISTRATION . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
C1704, C1705, C1706, C1707 LOW TIRE
PRESSURE . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
C1708, C1709, C1710, C1711 TIRE PRES-
SURE SENSOR . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
C1716, C1717, C1718, C1719 TIRE PRES-
SURE SENSOR . . . . . . . . . . . . .
Revision: 2012 March
2011 Murano CrossCabriolet
WT-2
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1729 VEHICLE SPEED SIGNAL . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
C1734 BCM . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
TIRE PRESSURE RECEIVER . . . . . . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
POWER SUPPLY AND GROUND CIRCUIT . .
Diagnosis Procedure . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . .
TPMS . . . . . . . . . . . . . . . . .
Symptom Table . . . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
DOES NOT TURN ON . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
DOES NOT TURN OFF . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
LOW TIRE PRESSURE WARNING LAMP
BLINKS . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
ID REGISTRATION CANNOT BE COMPLET-
ED . . . . . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . .
NVH Troubleshooting Chart . . . . . . . . .
PERIODIC MAINTENANCE . . . . . ...
ROAD WHEEL . . . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . .
Wheel Balance Adjustment . . . . . . . . . .
Tire Rotation . . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ..
ROAD WHEEL TIRE ASSEMBLY . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
How to Handle Puncture Repair Agent . . . . ...
TIRE PRESSURE SENSOR . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
TIRE PRESSURE RECEIVER . . . . . . ...
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Road Wheel . . . . . . . . . . . . . . .
Tire Air Pressure . . . . . . . . . . . . . .
Revision: 2012 March
2011 Murano CrossCabriolet
PRECAUTIONS
WT-3
< PRECAUTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006941795
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Battery Service
INFOID:0000000007232614
Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.
Service Procedure Precautions for Models with a Pop-up Roll Bar
INFOID:0000000007232615
WARNING:
Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll
over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.
• Before removing and installing the pop-up roll bar component parts and harness, always turn the
ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)
• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS
AIR BAG CONTROL warnings in the Service Manual.
Service Notice and Precautions for TPMS
INFOID:0000000006941796
• Low tire pressure warning lamp blinks for 1min, then turns ON when occurring any malfunction except low
tire pressure. Delete the memory with CONSULT, or register the ID to turn low tire pressure warning lamp
Revision: 2012 March
2011 Murano CrossCabriolet
WT-4
< PRECAUTION >
PRECAUTIONS
OFF. Refer to
WT-10, "AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
• ID registration is required when replacing or rotating wheels, replacing tire pressure sensor or BCM. Refer to
• Replace grommet seal, valve core and cap of tire pressure sensor in TPMS every tire replacement by reach-
ing wear limit of tire. Refer to
Service Notice and Precautions for Road Wheel
INFOID:0000000007232616
• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it on the specified vehicle only.
• Use Genuine NISSAN parts for the road wheels, valve caps and wheel nuts.
• Always use them after adjusting the wheel balance. For the balance weights, use Genuine NISSAN alumi-
num wheel weights.
• Use caution when handling the aluminum wheels, because they can be easily scratched. When removing
dirt, do not use any abrasives, a wire brush, or other items that may scratch the coating. Use a neutral deter-
gent if a detergent is needed.
• After driving on roads scattered with anti-icing salts, wash off the wheels completely.
• When installing road wheels onto the vehicle, always wipe off any dirt or foreign substances to prevent them
from being trapped between the contact surfaces of wheel.
• Never apply oil to nut and bolt threads.
• When tightening the valve cap there is a risk of damaging the valve cap if a tool is used. Tighten by hand.
Revision: 2012 March
2011 Murano CrossCabriolet
PREPARATION
WT-5
< PREPARATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000006941799
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000006941800
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-45295)
Tire pressure sensor activation tool
Tire pressure sensor wake-up procedure and
ID registration
SEIA0462E
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
Revision: 2012 March
2011 Murano CrossCabriolet
WT-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000006941801
Component Description
INFOID:0000000006941802
BCM
INFOID:0000000006941803
The BCM reads the air pressure signal received by the tire pressure receiver, and controls the low tire pres-
sure warning lamp operation. It also has a judgment function to detect a system malfunction.
1.
Tire pressure sensor
2.
BCM
3.
Tire pressure receiver
A.
Wheel
B.
Behind of combination meter
C.
Instrument lower panel LH
D.
Low tire pressure warning lamp, infor-
mation display (in combination meter)
JSEIA0308ZZ
Component parts
Function
BCM (Body Control Module)
Tire pressure sensor
Tire pressure receiver
WT-7, "Tire Pressure Receiver"
Turn signal lamp
ID registration of each wheel has been completed, turn signal lamp flashes.
Combination meter
Transmits the vehicle speed signal via CAN communication to BCM.
Receives the following signals via CAN communication to BCM.
• Low tire pressure warning lamp signal
• TPMS malfunction warning lamp signal
Low tire pressure warning lamp
Information display
Revision: 2012 March
2011 Murano CrossCabriolet
COMPONENT PARTS
WT-7
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
Tire Pressure Sensor
INFOID:0000000006941804
The tire pressure sensor integrated with a valve is installed on a wheel, and transmits a detected air pressure
signal by radio wave.
Tire Pressure Receiver
INFOID:0000000006941805
The tire pressure receiver receives the air pressure signal transmitted by the tire pressure sensor in each
wheel.
Information Display
INFOID:0000000006941806
The vehicle information display is shown when a low tire pressure warning lamp signal is transmitted from
BCM to combination meter via CAN communication.
Condition
Vehicle information display
Ignition switch OFF
Not indicated
Ignition switch ON
Low tire pressure warning lamp remains ON after blinking for one
minute. [Tire Pressure Monitoring System (TPMS) malfunction.]
Not indicated
Ignition switch ON
Low tire pressure warning lamp remains ON. (low tire pressure)
Indicated
Revision: 2012 March
2011 Murano CrossCabriolet
WT-8
< SYSTEM DESCRIPTION >
TPMS
TPMS
System Description
INFOID:0000000006941807
During driving, the TPMS (Tire Pressure Monitoring System) receives the signal transmitted from tire pressure
sensor installed in each wheel. The BCM (Body Control Module) of this system has pressure judgment and
trouble diagnosis functions. When the tire pressure monitoring system detects low inflation pressure or
another unusual symptom, the low tire pressure warning lamps in the combination meter comes on.
SYSTEM DIAGRAM
INPUT/OUTPUT SIGNAL
The signal transmission/reception between units via a communication line is mainly as listed in the following
table.
LOW TIRE PRESSURE WARNING LAMP INDICATION CONDITION
Uses CAN communication from the BCM to illuminate the low tire pressure warning lamp on the combination
meter.
JSEIA0157GB
Component parts
Signal item
BCM
Transmits the following signals via CAN communication to combination meter.
• Low tire pressure warning lamp signal
• TPMS malfunction warning lamp signal
Combination meter
Transmits the vehicle speed signal via CAN communication to BCM.
Condition
Low tire pressure warning lamp
Ignition switch OFF
OFF
Ignition switch ON
(system normal)
Warning lamp turns on for 1second, then turns off.
Low tire pressure
ON
Tire pressure sensor ID not registered in BCM
Tire pressure monitoring system malfunction
(Other diagnostic item)
Warning lamp blinks 1 min, then turns on.
Tire pressure sensor is in OFF state
Blink
(Blinking pattern depends on the positions of non-operational tire pressure sensors.)
Revision: 2012 March
2011 Murano CrossCabriolet
DIAGNOSIS SYSTEM (BCM)
WT-9
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000007232621
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
—
AIR CONDITONER*
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk lid opener system
TRUNK
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
Revision: 2012 March
2011 Murano CrossCabriolet
WT-10
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
NOTE:
*: Power supply position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position, and
any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power supply position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
TOR)
INFOID:0000000006941809
APPLICATION ITEMS
CONSULT performs the following functions via CAN communication with BCM.
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”*)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK” to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”*
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”*) to low power consumption mode
LOCK
Power supply position is “LOCK”*
OFF
Power supply position is “OFF” (Ignition switch OFF)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Revision: 2012 March
2011 Murano CrossCabriolet
DIAGNOSIS SYSTEM (BCM)
WT-11
< SYSTEM DESCRIPTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SELF DIAGNOSTIC RESULT
When “CRNT” is displayed on self-diagnosis result,
• The system is presently malfunctioning.
When “PAST” is displayed on self-diagnosis result,
• System malfunction in the past is detected, but the system is presently normal.
DATA MONITOR MODE
Screen of data monitor mode is displayed.
NOTE:
When malfunction is detected, CONSULT perform REAL-TIME DIAGNOSIS.
Also, any malfunction detected while in this mode will be displayed at real time.
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction location may
be different from that displayed on CONSULT.
ACTIVE TEST MODE
NOTE:
Before performing the self-diagnosis, be sure to register the ID, or erase the actual malfunction may be differ-
ent from that displayed on CONSULT.
TEST ITEM LIST
WORK SUPPORT MODE
Diagnosis mode
Function Description
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Work Support
Components can be quickly and accurately adjusted.
Monitor item (Unit)
Remark
AIR PRESS FL (kPa//kg/cm
2
/Psi)
Tire pressure
AIR PRESS FR (kPa//kg/cm
2
/Psi)
AIR PRESS RR (kPa//kg/cm
2
/Psi)
AIR PRESS RL (kPa//kg/cm
2
/Psi)
ID REGST FL1 (Green/Red)
Registration ID
ID REGST FR1 (Green/Red)
ID REGST RR1 (Green/Red)
ID REGST RL1 (Green/Red)
WARNING LAMP (On/Off)
Low tire pressure warning lamp
BUZZER (On/Off)
NOTE:
This item is displayed, but cannot be use this item.
Test item
Content
WARNING LAMP
This test is able to check to check that the low tire pressure warning lamp turns on.
ID REGIST WARNING
This test is able to check to check that the low tire pressure warning lamp turns on.
FLASHER
This test is able to check to check that each turn signal lamp turns on.
HORN
This test is able to check to check that the horn sounds.
Revision: 2012 March
2011 Murano CrossCabriolet
WT-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
Item
Description
ID READ
Registered tire pressure sensor ID can be displayed.
ID REGIST
Tire pressure sensor ID can be registered.
Revision: 2012 March
2011 Murano CrossCabriolet
BCM
WT-13
< ECU DIAGNOSIS INFORMATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
ECU DIAGNOSIS INFORMATION
BCM
List of ECU Reference
INFOID:0000000006941810
ECU
Reference
BCM
BCS-53, "DTC Inspection Priority Chart"
Revision: 2012 March
2011 Murano CrossCabriolet
WT-14
< WIRING DIAGRAM >
TIRE PRESSURE MONITORING SYSTEM
WIRING DIAGRAM
TIRE PRESSURE MONITORING SYSTEM
Wiring Diagram
INFOID:0000000006941811
JCEWM0254GB
Revision: 2012 March
2011 Murano CrossCabriolet
TIRE PRESSURE MONITORING SYSTEM
WT-15
< WIRING DIAGRAM >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
JCEWA0245GB
Revision: 2012 March
2011 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст