Nissan GT-R (2007-2014 year). STEERING SYSTEM / TRANSAXLE & TRANSMISSION. Service Manual — part 3
SHIFT POSITION
TM-15
< PERIODIC MAINTENANCE >
[TRANSMISSION: GR6Z30A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SHIFT POSITION
Inspection and Adjustment
INFOID:0000000009162744
INSPECTION
1.
Turn the ignition switch to ON at the shift lever P position.
2.
The shift lever can shift from the P position to the R position when the brake pedal is depressed. Alterna-
tively, the shift lever cannot shift from the P position to the R position without the brake pedal depressed.
3.
Operate the shift lever and check for excessive effort, sticking, noise or rattle.
4.
When the shift lever is operated, a click is felt, and the fixed position is correct and corresponds to the shift
position indicator in the combination meter
5.
Check that the shift lever is shifted through all the shift positions
in the manner shown in the figure.
6.
Check in the P and N positions that the knob button can be
operated without sticking when the button is pressed without the
shift lever pressed forward and backward.
7.
Check that in the R position the shift lever can be operated with-
out sticking when the shift lever is operated left and right.
8.
The back-up lamp can turn on and the reverse warning buzzer can sound with the shift lever in the R posi-
tion only.
9.
Check that the engine can be started with the shift lever in the P and N positions only.
10. The transmission is completely locked with the shift lever in the P position.
11. The shift position indicator of combination meter should change to the A range display or M range display
when the shift lever is operated to the M position.
12. The shift position indicator in the combination meter should not change when each load of 30 N (3.1 kg) is
applied (pressed) to front and rear side at the shift lever in the P position, front side at the shift lever in the
R position, front side at the shift lever in the N position and rear side at the shift lever in the A position.
ADJUSTMENT
1.
Disconnect the control cable from the A/T shift selector assembly.
2.
Shift the parking lever of transmission assembly to the P range
(A).
3.
Rotate the wheels at least a quarter turn and the Park position
mechanism is fully engaged.
4.
Shift the shift lever to the P position.
5.
Install the socket of the control cable to the A/T shift selector
assembly, and fix them with lock plate.
6.
Insert the I-end bolt into the cable lever of the A/T shift selector
assembly, and apply the load of 9.8 N (1 kg) in the cable lever P
direction (toward vehicle front) to the control cable.
7.
Release the control cable and temporarily tighten the lock nut. Then, tighten the lock nut to the specified
torque.
A
: Depress the brake pedal. Press and operate the knob button.
B
: Press and operate the knob button.
C
: Operate without condition.
D
: Automatic return.
NNDIA0020JP
B
: Other than P position
:14.7 N·m (1.5 kg-m, 11 ft-lb)
NNDIA0011ZZ
2014 GT-R
TM-16
< REMOVAL AND INSTALLATION >
[TRANSMISSION: GR6Z30A]
A/T SHIFT SELECTOR
REMOVAL AND INSTALLATION
A/T SHIFT SELECTOR
Exploded View
INFOID:0000000009162748
Removal and Installation
INFOID:0000000009162749
CAUTION:
Be careful of the following items because the range sensor is an important device to detect the shift
lever position.
• Keep range sensor (A) away from magnetic cards and mag-
netic objects during work.
• For a person with an electro-medical apparatus, keep the
range sensor away from the device.
• Keep foreign objects away from the opening (B) of range sen-
sor during work.
• Never touch the range sensor and sensor mounting screw.
• Always shift the shift lever to the P position during work.
REMOVAL
1.
Shift lever knob
2.
Lock pin
3.
Knob cover
4.
Position indicator lamp
5.
Slide cover
6.
Slide plate
7.
A/T shift selector assembly
8.
Push-button ignition switch
Refer to
in GI section for the symbols shown in the figure.
NNDIA0016GB
NNDIA0001ZZ
2014 GT-R
A/T SHIFT SELECTOR
TM-17
< REMOVAL AND INSTALLATION >
[TRANSMISSION: GR6Z30A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Shift the shift lever to the P position.
2.
Lower the rear side of the knob cover (1) downward.
3.
Pull out the lock pin (2) from the shift lever knob (3).
4.
Remove the shift lever knob and the knob cover.
5.
Remove the console finisher assembly, instrument side panel
LH/RH, and center console assembly. Refer to
.
6.
Disconnect the control cable from the A/T shift selector assem-
bly.
7.
Disconnect the push-button ignition switch connector and the
range sensor connector, and remove the harness clip.
8.
Remove the A/T shift selector assembly mounting bolt.
9.
Remove the A/T shift selector assembly from the vehicle.
CAUTION:
Never place the A/T shift selector assembly upside-down after removal. In addition, never place
the range sensor side down.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Refer to “ADJUSTMENT” in
TM-15, "Inspection and Adjustment"
when installing the control cable to the A/T
shift selector assembly.
• Note the following items when installing the shift lever knob.
1.
Install the lock pin (1) to the shift lever knob (2).
2.
Install the knob cover (3) to the shift lever knob.
3.
Insert the shift lever knob into the shift lever until it clicks.
Disassembly and Assembly
INFOID:0000000009162750
DISASSEMBLY
CAUTION:
Always shift the shift lever in the N position when performing disassembly and assembly of A/T shift
selector assembly.
1.
Press the shift lock release button, and then shift the shift lever in the N position.
2.
Insert a flat-bladed screwdriver into tabs (A: 4 locations), and
remove the position indicator plate (1) from the A/T shift selector
assembly (2) while lifting it up.
CAUTION:
The tabs crack easily. Be careful when removing.
3.
Remove the starter switch from the position indicator plate.
4.
Remove the slide cover from the A/T shift selector assembly.
Assembly
Note the following, and assemble in the reverse order of disassembly.
• Align the convex area (A) of slide cover (1) with the convex area (B) of A/T shift selector assembly (2) as
shown in the figure, and then install the position indicator plate. Check the shift lever movement after instal-
lation. Assemble again if any malfunctioning condition is detected.
NNDIA0126ZZ
NNDIA0127ZZ
NNDIA0128ZZ
2014 GT-R
TM-18
< REMOVAL AND INSTALLATION >
[TRANSMISSION: GR6Z30A]
A/T SHIFT SELECTOR
Inspection
INFOID:0000000009162751
INSPECTION AFTER INSTALLATION
Check the shift position after installation. Adjust the shift position if any malfunctioning condition is detected.
Refer to
TM-15, "Inspection and Adjustment"
NNDIA0002ZZ
2014 GT-R
OIL PAN
TM-19
< REMOVAL AND INSTALLATION >
[TRANSMISSION: GR6Z30A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Exploded View
INFOID:0000000009162757
1.
Transmission assembly
2.
Oil pan gasket
3.
Magnet
4.
Oil pan
5.
Drain plug
6.
Drain tube
Refer to
in GI section for the symbols shown in the figure.
JSDIA2951GB
2014 GT-R
TM-20
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSMISSION: GR6Z30A]
TRANSMISSION ASSEMBLY
UNIT DISASSEMBLY AND ASSEMBLY
TRANSMISSION ASSEMBLY
Exploded View
INFOID:0000000009162778
1.
Transmission assembly
2.
Filler plug
3.
Filler plug gasket
4.
3rd-5th check pin
5.
Plane washer
6.
O-ring
7.
Plug
8.
Idler bolt
9.
Plane washer
: Apply Genuine NISSAN Transmission oil R35 Special.
in GI section for the symbols other than above.
NNDIA0040GB
2014 GT-R
SERVICE DATA AND SPECIFICATIONS (SDS)
TM-21
< SERVICE DATA AND SPECIFICATIONS (SDS)
[TRANSMISSION: GR6Z30A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000009162780
Applied model
VR38DETT
AWD
Transmission model
GR6Z30A
2014 GT-R
TM-22
< SERVICE DATA AND SPECIFICATIONS (SDS)
[TRANSMISSION: GR6Z30A]
SERVICE DATA AND SPECIFICATIONS (SDS)
Transmission
Transmission model code number
(*1)
KJ10A
Operating system
Remote control floor shifter and paddle shifter
Shift position
P
Fixed to output shaft (engine start is possible)
R
Reverse
N
Neutral (engine start is possible)
A
R
1
←→
2
←→
3
←→
4
←→
5
←→
6
Normal
1
←→
2
←→
3
←→
4
←→
5
←→
6
SAVE
1
←→
2
←→
3
←→
4
←→
5
←→
6
M
R
6
M
Fixed to 6GR
With the under rev protection au-
tomatic shift function
(In order to keep running function,
it shifts down automatically when
engine speed becomes low.)
5
M
Fixed to 5GR
4
M
Fixed to 4GR
3
M
Fixed to 3GR
2
M
Fixed to 2GR
1
M
Fixed to 1GR
Normal
6
M
Fixed to 6GR
With the over rev and under rev
protection automatic shift function
(In order to keep running function,
it shifts down automatically when
engine speed becomes low. In or-
der to avoid engine over-speed, it
shifts up automatically under red
zone.)
5
M
Fixed to 5GR
4
M
Fixed to 4GR
3
M
Fixed to 3GR
2
M
Fixed to 2GR
1
M
Fixed to 1GR
SAVE
6
M
Fixed to 6GR
With the over rev and under rev
protection automatic shift function
(In order to keep running function,
it shifts down automatically when
engine speed becomes low. In or-
der to avoid engine over-speed, it
shifts up automatically under red
zone.)
5
M
Fixed to 5GR
4
M
Fixed to 4GR
3
M
Fixed to 3GR
2
M
Fixed to 2GR
1
M
Fixed to 1GR
Gear ratio
1GR
4.056
2GR
2.301
3GR
1.595
4GR
1.248
5GR
1.001
6GR
0.796
Reverse
3.383
Control system
Electronic controls
Function
Self-diagnosis function
With
Fail safe function
With
Synchronizer system
Borg Warner type triple cone synchronizer
Oil pump
Type
External gear pump
Drive type
Drive with the engine
Oil
Recommended
Genuine NISSAN Transmission Oil R35 Special
Capacity
9.4 liter (9-7/8 US qt, 8-1/4 Imp qt)
(*2)
Applied model
VR38DETT
AWD
2014 GT-R
SERVICE DATA AND SPECIFICATIONS (SDS)
TM-23
< SERVICE DATA AND SPECIFICATIONS (SDS)
[TRANSMISSION: GR6Z30A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• *1: The model No. refers to the lower five digits of the part number (32000 XXXXX).
• *2: The indicated oil level is only a guide, therefore check the oil level according to the Service Manual.
2014 GT-R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст