Juke F15 (2012 year). Service Repair Manual — part 294

PCS

SYSTEM

PCS-71

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

Emergency stop operation

• Press and hold the push-button ignition switch for 2 seconds or more.

• Press the push-button ignition switch 3 times or more within 1.5 seconds.

Fail-safe

INFOID:0000000006659786

FAIL-SAFE CONTROL BY DTC

BCM performs fail-safe control when any DTC are detected.

Power supply position

Engine start/stop condition

Push-button

ignition

switch oper-

ation fre-

quency

CVT models

M/T models

Selector le-
ver position

Brake pedal

operation

condition

Normal condition

Special condition

Control lever

position

Clutch pedal

operation

condition

Control lever

position

Brake pedal

operation

condition

Engine is running

→

ACC

—

Emergency
stop opera-

tion

Engine stall return op-
eration while driving

N position

Not de-

pressed

—

Depressed

Neutral

—

Display contents of CONSULT

Fail-safe

Cancellation

B2013: ID DISCORD BCM-S/L

Inhibit engine cranking

When communication between BCM and steering lock unit are commu-
nicated normally.

B2014: CHAIN OF S/L-BCM

Inhibit engine cranking

When communication between BCM and steering lock unit are commu-
nicated normally.

B2192: ID DISCORD BCM-ECM

Inhibit engine cranking

Erase DTC

B2193: CHAIN OF BCM-ECM

Inhibit engine cranking

Erase DTC

B2195: ANTI-SCANNING

Inhibit engine cranking

Ignition switch ON

→

OFF

B2196: DONGLE NG

Inhibit engine cranking

Erase DTC

B2198: NATS ANTENNA AMP

Inhibit engine cranking

Erase DTC

B2557: VEHICLE SPEED

Inhibit steering lock

When the following CAN signal status (vehicle speed signal) becomes
consistent
• Vehicle speed signal (ABS)
• Vehicle speed signal (Meter)

B2601: SHIFT POSITION

Inhibit steering lock

500 ms after the following signal reception status becomes consistent
• Detention switch signal
• P range signal (CAN)

B2602: SHIFT POSITION

Inhibit steering lock

5 seconds after the following BCM recognition conditions are fulfilled
• Ignition switch is in the ON position
• Detention switch signal: P position (push selector button) or except P

position (12 V)

• Vehicle speed: 4 km/h (2.5 MPH) or more

B2603: SHIFT POSI STATUS

Inhibit steering lock

500 ms after any of the following BCM recognition conditions are fulfilled
• Status 1
- Ignition switch is in the ON position
- Detention switch signal: P position (push selector button) or except P

position (12 V)

- P/N position signal: Except P and N positions (0 V)
• Status 2
- Ignition switch is in the ON position
- Detention switch signal: P position (release selector button) (0 V)
- P/N position signal: P or N positions (12 V)

PCS-72

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

SYSTEM

B2604: PNP/CLUTCH SW

Inhibit steering lock

500 ms after any of the following BCM recognition conditions are fulfilled
• Status 1
- Ignition switch is in the ON position
- P/N position signal: P or N position (12 V)
- Shift position signal (CAN): P or N position
• Status 2
- Ignition switch is in the ON position
- P/N position signal: Except P and N positions (0 V)
- Shift position signal (CAN): Except P and N position

B2605: PNP/CLUTCH SW

Inhibit steering lock

500 ms after any of the following BCM recognition conditions are fulfilled
• Status 1
- Power position: IGN
- P/N position signal: Except P and N positions (0 V)
- Interlock/PNP switch signal (CAN): OFF
• Status 2
- Ignition switch is in the ON position
- P/N position signal: P or N position (12 V)
- Interlock/PNP switch signal (CAN): ON

B2608: STARTER RELAY

Inhibit engine cranking

500 ms after the following signal communication status becomes con-
sistent
• Starter motor relay control signal
• Starter relay status signal (CAN)

B2609: S/L STATUS

• Inhibit engine crank-

ing

• Inhibit steering lock

When the following steering lock conditions agree
• BCM steering lock control status
• Steering lock condition No. 1 signal status
• Steering lock condition No. 2 signal status

B260B: STEERING LOCK UNIT

Inhibit steering lock

Erase DTC

B260D: STEERING LOCK UNIT

Inhibit steering lock

Erase DTC

B260F: ENG STATE SIG LOST

Inhibit engine cranking

When any of the following conditions are fulfilled
• Power position changes to ACC
• Receives engine status signal (CAN)

B2612: S/L STATUS

• Inhibit engine crank-

ing

• Inhibit steering lock

When any of the following conditions are fulfilled
• Steering lock unit status signal (CAN) is received normally
• The BCM steering lock control status matches the steering lock status

recognized by the steering lock unit status signal (CAN from IPDM E/
R)

B2619: BCM

Inhibit engine cranking

1 second after the steering lock unit power supply output control inside
BCM becomes normal

B26EF: STRG LCK RELAY OFF

Inhibit engine cranking

When the following conditions are fulfilled
• Steering lock relay signal (CAN): ON
• Steering lock unit status signal (CAN): ON

B26F0: STRG LCK RELAY ON

Inhibit engine cranking

When the following conditions are fulfilled
• Steering lock relay signal (CAN): OFF
• Steering lock unit status signal (CAN): OFF

B26F1: IGN RELAY OFF

Inhibit engine cranking

When the following conditions are fulfilled
• Ignition switch ON signal (CAN: Transmitted from BCM): ON
• Ignition switch ON signal (CAN: Transmitted from IPDM E/R): ON

B26F2: IGN RELAY ON

Inhibit engine cranking

When the following conditions are fulfilled
• Ignition switch ON signal (CAN: Transmitted from BCM): OFF
• Ignition switch ON signal (CAN: Transmitted from IPDM E/R): OFF

B26F3: START CONT RLY ON

Inhibit engine cranking

When the following conditions are fulfilled
• Starter control relay signal (CAN: Transmitted from BCM): OFF
• Starter control relay signal (CAN: Transmitted from IPDM E/R): OFF

B26F4: START CONT RLY OFF

Inhibit engine cranking

When the following conditions are fulfilled
• Starter control relay signal (CAN: Transmitted from BCM): ON
• Starter control relay signal (CAN: Transmitted from IPDM E/R): ON

Display contents of CONSULT

Fail-safe

Cancellation

PCS

SYSTEM

PCS-73

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

REAR WIPER MOTOR PROTECTION

BCM detects the rear wiper stopping position according to the rear wiper stop position signal.
When the rear wiper stop position signal does not change for more than 5 seconds while driving the rear
wiper, BCM stops power supply to protect the rear wiper motor.

Condition of cancellation

More than 1 minute is passed after the rear wiper stop.

Turn rear wiper switch OFF.

Operate the rear wiper switch or rear washer switch.

FAIL-SAFE CONTROL BY LIGHT AND RAIN SENSOR MALFUNCTION

BCM detects the light and rain sensor serial link error and the light and rain sensor malfunction.
BCM controls the following fail-safe when light and rain sensor has a malfunction.

Fail-safe Control

• Auto light control: Headlamp low beam, parking lamp, license plate lamp and tail lamp are turned ON.
• Front wiper control
- Front wiper switch AUTO and sensing rain drop: The condition just before the activation of fail-safe is main-

tained until the front wiper switch is turned OFF.

- Front wiper switch AUTO and not sensing rain drop: Front wiper is LO operation until the front wiper switch is

turned off.

FAIL-SAFE CONTROL OF COMBINATION SWITCH READING FUNCTION CAUSED BY LOW
POWER SUPPLY VOLTAGE

If voltage of battery power supply lower, BCM maintains combination switch reading to the status when input
voltage is less than approximately 9 V.
NOTE:
When voltage of battery power supply is approximately 9 V or more, combination switch reading function
returns to normal operation.

B26F7: BCM

Inhibit engine cranking
by Intelligent Key sys-
tem

When room antenna and luggage room antenna functions normally

U0415: VEHICLE SPEED

Inhibit steering lock

When vehicle speed signal (Meter) (CAN) is received normally

Display contents of CONSULT

Fail-safe

Cancellation

PCS-74

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

DIAGNOSIS SYSTEM (BCM)

DIAGNOSIS SYSTEM (BCM)

COMMON ITEM

COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)

INFOID:0000000006747512

APPLICATION ITEM

CONSULT-III performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

: Applicable item

NOTE:

• *1: This item is displayed, but not used.

• *2: For models with automatic A/C, this diagnosis mode is not used.

FREEZE FRAME DATA (FFD)

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

Rear window defogger

REAR DEFOGGER

Warning chime

BUZZER

Interior room lamp timer

INT LAMP

Exterior lamp

HEAD LAMP

Wiper and washer

WIPER

Turn signal and hazard warning lamps

FLASHER

• Automatic A/C
• Manual A/C

AIR CONDITONER

• Intelligent Key system
• Engine start system

INTELLIGENT KEY

Combination switch

COMB SW

Body control system

BCM

NVIS - NATS

IMMU

Interior room lamp battery saver

BATTERY SAVER

Back door open

TRUNK

Theft warning alarm

THEFT ALM

—

RETAINED PWR*

Signal buffer system

SIGNAL BUFFER

PCS

DIAGNOSIS SYSTEM (BCM)

PCS-75

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.

INTELLIGENT KEY

INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) (With Super
Lock)

INFOID:0000000006747513

WORK SUPPORT

CONSULT screen item

Indication/Unit

Description

Vehicle Speed

km/h

Vehicle speed of the moment a particular DTC is detected

Odo/Trip Meter

Total mileage (Odometer value) of the moment a particular DTC is detected

Vehicle Condition

SLEEP>LOCK

Power position status of
the moment a particular
DTC is detected

While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”)

SLEEP>OFF

While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)

LOCK>ACC

While turning power supply position from “LOCK” to “ACC”

ACC>ON

While turning power supply position from “ACC” to “IGN”

RUN>ACC

While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)

CRANK>RUN

While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)

RUN>URGENT

While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)

ACC>OFF

While turning power supply position from “ACC” to “OFF”

OFF>LOCK

While turning power supply position from “OFF” to “LOCK”

OFF>ACC

While turning power supply position from “OFF” to “ACC”

ON>CRANK

While turning power supply position from “IGN” to “CRANKING”

OFF>SLEEP

While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode

LOCK>SLEEP

While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”.) to low power consumption mode

LOCK

Power supply position is “LOCK” (Ignition switch OFF with steer-
ing is locked.)

OFF

Power supply position is “OFF” (Ignition switch OFF with steering
is unlocked.)

ACC

Power supply position is “ACC” (Ignition switch ACC)

Power supply position is “IGN” (Ignition switch ON with engine
stopped)

ENGINE RUN

Power supply position is “RUN” (Ignition switch ON with engine
running)

CRANKING

Power supply position is “CRANKING” (At engine cranking)

IGN Counter

0 - 39

The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1

→

3...38

→

39 after returning to the normal condition

whenever ignition switch OFF

→

ON.

• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

PCS-76

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

DIAGNOSIS SYSTEM (BCM)

Monitor item

Description

INSIDE ANT DIAGNOSIS

This function allows inside key antenna self-diagnosis

LOCK/UNLOCK BY I-KEY

Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation

ENGINE START BY I-KEY

Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

TRUNK/GLASS HATCH OPEN

NOTE:
This item is displayed, but cannot be monitored

PANIC ALARM SET

NOTE:
This item is displayed, but cannot be monitored

TRUNK OPEN DELAY

NOTE:
This item is displayed, but cannot be monitored

LO- BATT OF KEY FOB WARN

Intelligent Key low battery warning mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

ANTI KEY LOCK IN FUNCTI

Key reminder function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

HAZARD ANSWER BACK

Hazard reminder function mode by door request switch and Intelligent Key button can be se-
lected from the following with this mode
• Lock Only: Door lock operation only
• Unlock Only: Door unlock operation only
• Lock/Unlock: Lock and unlock operation
• Off: Non-operation

ANS BACK I-KEY LOCK

Buzzer reminder function (lock operation) mode by door request switch can be selected from
the following with this mode
• Horn Chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• Off: Non-operation

ANS BACK I-KEY UNLOCK

Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operation with this mode
• On: Operate
• Off: Non-operation

SHORT CRANKING OUTPUT

Starter motor can operate during the times below
• 70 msec
• 100 msec
• 200 msec

CONFIRM KEY FOB ID

It can be checked whether Intelligent Key ID code is registered or not in this mode

AUTO LOCK SET

Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes

ANSWER BACK FUNCTION

Buzzer reminder function mode by Intelligent Key button can be selected from the following
with this mode
• On: Operate
• Off: Non-operation

TAKE OUT FROM WIN WARN SET

NOTE:
This item is indicated, but not used

RETRACTABLE MIRROR SET

Auto retractable door mirror function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

PCS

DIAGNOSIS SYSTEM (BCM)

PCS-77

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

SELF-DIAG RESULT

Refer to

BCS-67, "DTC Index"

DATA MONITOR

Monitor Item

Condition

REQ SW -DR

Indicates [On/Off] condition of door request switch (driver side)

REQ SW -AS

Indicates [On/Off] condition of door request switch (passenger side)

REQ SW -BD/TR

Indicates [On/Off] condition of back door request switch

PUSH SW

Indicates [On/Off] condition of push-button ignition switch

CLUTCH SW*

Indicates [On/Off] condition of clutch interlock switch

BRAKE SW 1

Indicates [On/Off]*

condition of stop lamp switch power supply

BRAKE SW 2

Indicates [On/Off] condition of stop lamp switch

DETE/CANCL SW

Indicates [On/Off] condition of P position

SFT PN/N SW

Indicates [On/Off] condition of P or N position

S/L -LOCK

Indicates [On/Off] condition of steering lock unit (LOCK)

S/L -UNLOCK

Indicates [On/Off] condition of steering lock unit (UNLOCK)

S/L RELAY -F/B

Indicates [On/Off] condition of steering lock relay

UNLK SEN -DR

Indicates [On/Off] condition of driver door UNLOCK status

PUSH SW -IPDM

Indicates [On/Off] condition of push-button ignition switch

IGN RLY1 -F/B

Indicates [On/Off] condition of ignition relay 1

DETE SW -IPDM

Indicates [On/Off] condition of P position

SFT PN -IPDM

Indicates [On/Off] condition of P or N position

SFT P -MET

Indicates [On/Off] condition of P position

SFT N -MET

Indicates [On/Off] condition of N position

ENGINE STATE

Indicates [Stop/Stall/Crank/Run] condition of engine states

S/L LOCK-IPDM

Indicates [On/Off] condition of steering lock unit (LOCK)

S/L UNLK-IPDM

Indicates [On/Off] condition of steering lock unit (UNLOCK)

S/L RELAY-REQ

Indicates [On/Off] condition of steering lock relay

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h]

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]

DOOR STAT-DR

Indicates [LOCK/READY/UNLK] condition of driver side door status

DOOR STAT-AS

Indicates [LOCK/READY/UNLK] condition of passenger side door status

ID OK FLAG

Indicates [Set/Reset] condition of key ID

PRMT ENG STRT

Indicates [Set/Reset] condition of engine start possibility

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored

RKE-LOCK

Indicates [On/Off] condition of LOCK signal from Intelligent Key

RKE-UNLOCK

Indicates [On/Off] condition of UNLOCK signal from Intelligent Key

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored

RKE-PANIC

NOTE:
This item is displayed, but cannot be monitored

RKE-MODE CHG

Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key

PCS-78

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

DIAGNOSIS SYSTEM (BCM)

: It is displayed but does not operate on CVT models.

: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) (Without Su-

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored

Monitor Item

Condition

Test item

Description

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation

INSIDE BUZZER

This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT-III screen is touched
• Key: Key warning chime sounds when CONSULT-III screen is touched
• Knob: OFF position warning chime sounds when CONSULT-III screen is touched
• Off: Non-operation

INDICATOR

This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT-III screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT-III screen is touched
• Off: Non-operation

INT LAMP

This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation

LCD

This test is able to check meter display information
• BP N: Engine start operation indicator lamp indicate when CONSULT-III screen is touched
• BP I: Engine start operation indicator lamp indicate when CONSULT-III screen is touched
• ID NG: This item is displayed, but cannot be monitored
• ROTAT: This item is displayed, but cannot be monitored
• SFT P: Shift P warning lamp indicate when CONSULT-III screen is touched
• INSRT: This item is displayed, but cannot be monitored
• BATT: Key warning lamp indicator when CONSULT-III screen is touched
• NO KY: Key warning lamp indicator when CONSULT-III screen is touched
• OUTKEY: Engine start operation indicator lamp indicate when CONSULT-III screen is

touched

• LK WN: Engine start operation indicator lamp indicate when CONSULT-III screen is touched

FLASHER

This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT-III screen is touched

P RANGE

This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched

PUSH SWITCH INDICATOR

This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is
touched

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.

TRUNK/BACK DOOR

This test is able to check back door opener actuator open operation.
This actuator opens when “Open” on CONSULT-III screen is touched.

RETRACTABLE MIRROR

This test is able to check auto retractable door mirror operation
• On: Operate
• Off: Non-operation

PCS

DIAGNOSIS SYSTEM (BCM)

PCS-79

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

per Lock)

INFOID:0000000006747514

WORK SUPPORT

Monitor item

Description

INSIDE ANT DIAGNOSIS

This function allows inside key antenna self-diagnosis

LOCK/UNLOCK BY I-KEY

Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation

ENGINE START BY I-KEY

Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

TRUNK/GLASS HATCH OPEN

NOTE:
This item is displayed, but cannot be monitored

PANIC ALARM SET

NOTE:
This item is displayed, but cannot be monitored

TRUNK OPEN DELAY

NOTE:
This item is displayed, but cannot be monitored

LO- BATT OF KEY FOB WARN

Intelligent Key low battery warning mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

ANTI KEY LOCK IN FUNCTI

Key reminder function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

HAZARD ANSWER BACK

ANS BACK I-KEY LOCK

ANS BACK I-KEY UNLOCK

Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operation with this mode
• On: Operate
• Off: Non-operation

SHORT CRANKING OUTPUT

Starter motor can operate during the times below
• 70 msec
• 100 msec
• 200 msec

CONFIRM KEY FOB ID

It can be checked whether Intelligent Key ID code is registered or not in this mode

AUTO LOCK SET

ANSWER BACK FUNCTION

Buzzer reminder function mode by Intelligent Key button can be selected from the following
with this mode
• On: Operate
• Off: Non-operation

PCS-80

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

DIAGNOSIS SYSTEM (BCM)

SELF-DIAG RESULT

Refer to

BCS-67, "DTC Index"

DATA MONITOR

TAKE OUT FROM WIN WARN SET

NOTE:
This item is indicated, but not used

RETRACTABLE MIRROR SET

Auto retractable door mirror function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

Monitor item

Description

Monitor Item

Condition

REQ SW -DR

Indicates [On/Off] condition of door request switch (driver side)

REQ SW -AS

Indicates [On/Off] condition of door request switch (passenger side)

REQ SW -BD/TR

Indicates [On/Off] condition of back door request switch

PUSH SW

Indicates [On/Off] condition of push-button ignition switch

CLUTCH SW*

Indicates [On/Off] condition of clutch interlock switch

BRAKE SW 1

Indicates [On/Off]*

condition of stop lamp switch power supply

BRAKE SW 2

Indicates [On/Off] condition of stop lamp switch

DETE/CANCL SW

Indicates [On/Off] condition of P position

SFT PN/N SW

Indicates [On/Off] condition of P or N position

S/L -LOCK

Indicates [On/Off] condition of steering lock unit (LOCK)

S/L -UNLOCK

Indicates [On/Off] condition of steering lock unit (UNLOCK)

S/L RELAY -F/B

Indicates [On/Off] condition of steering lock relay

UNLK SEN -DR

Indicates [On/Off] condition of driver door UNLOCK status

PUSH SW -IPDM

Indicates [On/Off] condition of push-button ignition switch

IGN RLY1 -F/B

Indicates [On/Off] condition of ignition relay 1

DETE SW -IPDM

Indicates [On/Off] condition of P position

SFT PN -IPDM

Indicates [On/Off] condition of P or N position

SFT P -MET

Indicates [On/Off] condition of P position

SFT N -MET

Indicates [On/Off] condition of N position

ENGINE STATE

Indicates [Stop/Stall/Crank/Run] condition of engine states

S/L LOCK-IPDM

Indicates [On/Off] condition of steering lock unit (LOCK)

S/L UNLK-IPDM

Indicates [On/Off] condition of steering lock unit (UNLOCK)

S/L RELAY-REQ

Indicates [On/Off] condition of steering lock relay

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h]

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]

DOOR STAT-DR

Indicates [LOCK/READY/UNLK] condition of driver side door status

DOOR STAT-AS

Indicates [LOCK/READY/UNLK] condition of passenger side door status

ID OK FLAG

Indicates [Set/Reset] condition of key ID

PRMT ENG STRT

Indicates [Set/Reset] condition of engine start possibility

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored

RKE-LOCK

Indicates [On/Off] condition of LOCK signal from Intelligent Key

RKE-UNLOCK

Indicates [On/Off] condition of UNLOCK signal from Intelligent Key

PCS

DIAGNOSIS SYSTEM (BCM)

PCS-81

< SYSTEM DESCRIPTION >

[POWER DISTRIBUTION SYSTEM]

: It is displayed but does not operate on CVT models.

: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored

RKE-PANIC

NOTE:
This item is displayed, but cannot be monitored

RKE-MODE CHG

Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored

Monitor Item

Condition

Test item

Description

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation

INSIDE BUZZER

INDICATOR

INT LAMP

This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation

LCD

touched

• LK WN: Engine start operation indicator lamp indicate when CONSULT-III screen is touched

FLASHER

This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT-III screen is touched

P RANGE

This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched

PUSH SWITCH INDICATOR

This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is
touched

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.