Juke F15 (2012 year). Service Repair Manual — part 86
DLK-368
< SYSTEM DESCRIPTION >
[TYPE 3]
REMOTE KEYLESS ENTRY SYSTEM
When Keyfob unlock button is operated while super lock of all doors is set, super lock of all doors is released,
and simultaneously, driver door are unlocked. When Keyfob unlock button is operated again, all doors are
unlocked.
SUPER LOCK RELEASE OPERATION (UNLOCK OERATION) WITHOUT ANTI-HIJACK MODE
When keyfob unlock button is operated while super lock of all doors is set, super lock of all doors is released,
and simultaneously, all doors are unlocked.
ANTI-HIJACK FUNCTION SETTING
With CONSULT-III
DLK-371, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (With Super Lock)"
.
Without CONSULT-III
• ON/OFF can be switched when keyfob lock button and unlock button are pressed simultaneously for 4 sec-
onds or more while steering lock is locked.
• When mode is switched, hazard warning lamp blinks.
OFF
→
ON
: 1 blinks
ON
→
OFF
: 3 blink
BACK DOOR OPENER SYSTEM
DLK-369
< SYSTEM DESCRIPTION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR OPENER SYSTEM
System Diagram
INFOID:0000000006554252
System Description
INFOID:0000000006554253
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM operates back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.
OPERATION CONDITION
If the following conditions are satisfied, back door opener operation is performed.
NOTE:
• When battery terminal is disconnected and reconnected during all doors unlock state, back door may not
open.
• Regardless of door lock actuator state, BCM resets recognition of all doors unlock state approximately 30
seconds after battery terminal is disconnected and BCM recognizes that all doors are in lock state.
• When battery terminal is reconnected and back door does not open, have BCM recognize that all doors are
in unlock state.
JMKIA6011GB
Back door opener switch operation
Operation condition
Back door open
• When back door is unlocked using back door opener request switch (anti-hijack
mode), or after BCM outputs all doors unlock signal
• Vehicle speed is less than 5 km/h (3 MPH)
DLK-370
< SYSTEM DESCRIPTION >
[TYPE 3]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000006748148
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
• *1: This item is displayed, but is not used.
• *2: For models with automatic A/C, this mode is not used.
DOOR LOCK
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
• Automatic A/C
• Manual A/C
• Manual heater
AIR CONDITONER
×
×
*
2
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
—
RETAINED PWR*
1
×
×
Signal buffer system
SIGNAL BUFFER
×
×
—
PANIC ALARM*
1
×
DIAGNOSIS SYSTEM (BCM)
DLK-371
< SYSTEM DESCRIPTION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (With Super Lock)
INFOID:0000000006445182
WORK SUPPORT
*: P range interlock door lock/unlock can be selected for M/T models, but automatic door lock/unlock function does not operate.
DATA MONITOR
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function can be changed to operate with this mode
• On: Operate
• Off: Non-operation
AUTOMATIC DOOR LOCK SELECT
Automatic door lock function can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 10 km/h (6 MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other
than the P position
AUTOMATIC DOOR UNLOCK SELECT
Automatic door unlock function can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to
OFF
• MODE 2*: All doors are unlocked when shifting the selector lever from any position other
than the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from
ON to OFF
• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position
other than the P to P position
• MODE 5: Driver side door is unlocked when key out of key switch
• MODE 6: All doors are unlocked when key out of key switch
AUTOMATIC LOCK/UNLOCK SET
Automatic door lock/unlock function can be selected from the following in this mode
• Off: Non-operation
• Unlock Only: Door unlock operation only
• Lock Only: Door lock operation only
• Lock/Unlock: Door lock and unlock operation
Monitor Item
Contents
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicated [On/Off] condition of key switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicated [On/Off] condition of back door switch
LOCK STATUS
Indicated [On/Off] condition of front door driver side
ACC ON SW
Indicated [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicated [On/Off] condition of lock signal from key fob
KEYLESS UNLOCK
Indicated [On/Off] condition of unlock signal from key fob
SHOCK SENSOR
Indicates [NOMAL/ON/OFF] condition of circuit between BCM and air bag diag-
nosis sensor unit
• NORMAL: Ignition switch ON (BCM is receiving normal condition signal from
air bag diagnosis sensor unit)
• ON: During the receiving of air bag signal from air bag diagnosis sensor unit
• OFF: After the receiving of air bag signal from air bag diagnosis sensor unit
KEY CYL LK-SW
NOTE:
This item is displayed, but cannot be monitored
DLK-372
< SYSTEM DESCRIPTION >
[TYPE 3]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
MULTI REMOTE ENT
MULTI REMOTE ENT : CONSULT-III Function (BCM - MULTI REMOTE ENT) (With
Super Lock)
INFOID:0000000006445183
DATA MONITOR
ACTIVE TEST
KEY CYL UN-SW
NOTE:
This item is displayed, but cannot be monitored
VEHICLE SPEED
Display the vehicle speed signal received from combination meter by numerical
value [Km/h]
Monitor Item
Contents
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LCK” on CONSULT-III screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen is
touched
• The back door lock actuator is unlocked when “BD ULK” on CONSULT-III screen is touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT-III screen is touched
DOOR LOCK IND
This test is able to check door lock status indicator operation
SUPER LOCK
This test is able to check super lock actuator operation
• The all super lock actuators are set when “LOCK” on CONSULT-III screen is touched
• The all super lock actuators are released when “UNLOCK” on CONSULT-III screen is touched
Monitor Item
Condition
IGN ON SW
Indicates [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicates [On/Off] condition of key switch
ACC ON SW
Indicates [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicates [On/Off] condition of lock signal from keyfob
KEYLESS UNLOCK
Indicates [On/Off] condition of unlock signal from keyfob
KYLS TRNK/HAT
NOTE:
This item is displayed, but cannot be tested
DOOR SW-DR
Indicates [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicates [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicates [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicates [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicates [On/Off] condition of back door switch
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be tested
CDL LOCK SW
Indicates [On/Off] condition of door lock and unlock switch
CDL UNLOCK SW
Indicates [On/Off] condition of door lock and unlock switch
KEYLESS PANIC
NOTE:
This item is displayed, but cannot be tested
DIAGNOSIS SYSTEM (BCM)
DLK-373
< SYSTEM DESCRIPTION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
WORK SUPPORT
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK) (With Super Lock)
INFOID:0000000006445184
DATA MONITOR
Test item
Description
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
FLASHER
This test is able to check flasher operation [LH/RH/Off]
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LCK” on CONSULT-III screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen is
touched
• The back door lock actuator is unlocked when “BD ULK” on CONSULT- III screen is touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT-III screen is touched
Test item
Description
REMO CONT IN REGIST
Keyfob ID code can be registered
REMO CONT IN ERASUR
Keyfob ID code can be erased
REMO CONT IN CONFIR
It can be checked whether Keyfob ID code is registered or not in this mode
HAZARD LAMP SET
Hazard and horn reminder function (hazard operation) mode can be changed in this mode
• MODE1: Non-operation
• MODE2: Unlock operation only
• MODE3: Lock operation only
• MODE4: Lock and unlock operation
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
PANIC ALARM SET
NOTE:
This item is displayed, but cannot be tested
TRUNK OPEN SET
NOTE:
This item is displayed, but cannot be tested
Monitor Item
Contents
KEY ON SW
Indicates [On/Off] condition of key switch.
LOCK STATUS
Indicates [On/Off] condition of front door driver side.
VEHICLE SPEED
Indicates [Km/h] condition of vehicle speed signal from combination meter.
IGN ON SW
Indicates [On/Off] condition of ignition switch.
TRNK OPNR SW
NOTE:
This item is displayed, but cannot be monitored.
KYLS TRNK/HAT
NOTE:
This item is displayed, but cannot be monitored.
DLK-374
< ECU DIAGNOSIS INFORMATION >
[TYPE 3]
BCM
ECU DIAGNOSIS INFORMATION
BCM
List of ECU Reference
INFOID:0000000006445185
ECU
Reference
BCM
DOOR & LOCK SYSTEM
DLK-375
< WIRING DIAGRAM >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
WIRING DIAGRAM
DOOR & LOCK SYSTEM
Wiring Diagram
INFOID:0000000006445187
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information/Explanation of Option Abbreviation"
JCKWA3295GB
DLK-376
< WIRING DIAGRAM >
[TYPE 3]
DOOR & LOCK SYSTEM
JCKWA3296GB
DOOR & LOCK SYSTEM
DLK-377
< WIRING DIAGRAM >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JCKWA3297GB
DLK-378
< BASIC INSPECTION >
[TYPE 3]
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000006445188
OVERALL SEQUENCE
DETAILED FLOW
JMKIA3620GB
DIAGNOSIS AND REPAIR WORK FLOW
DLK-379
< BASIC INSPECTION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
GET INFORMATION FOR SYMPTOM
1.
Get the detailed information from the customer about the symptom (the condition and the environment
when the incident/malfunction occurred).
2.
Check operation condition of the function that is malfunctioning.
>> GO TO 2.
2.
CHECK FOR DTC
1.
Check DTC for BCM.
2.
Perform the following procedure if DTC is displayed.
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real-time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real-time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
If two or more DTCs are detected, refer to
BCS-140, "DTC Inspection Priority Chart"
(BCM) and determine
trouble diagnosis order.
Is DTC detected?
YES
>> GO TO 7.
NO
>> Refer to
GI-42, "Intermittent Incident"
.
6.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to Symptom Diagnosis based on the confirmed symptom in step 4.
>> GO TO 7.
7.
DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure is described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
>> GO TO 8.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
DLK-380
< BASIC INSPECTION >
[TYPE 3]
DIAGNOSIS AND REPAIR WORK FLOW
3.
Check DTC. If DTC is displayed, erase it.
>> GO TO 9.
9.
FINAL CHECK
When DTC was detected in step 9, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunctions have been fully repaired.
When symptom was described by the customer, refer to the confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Are all malfunctions corrected?
NO (DTC is detected)>>GO TO 7.
NO (Symptom remains)>>GO TO 6.
YES
>> INSPECTION END
KEYFOB ID REGISTRATION
DLK-381
< BASIC INSPECTION >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEYFOB ID REGISTRATION
Description
INFOID:0000000006445189
Perform the following procedure after BCM is replaced or when new keyfob ID is registered
NOTE:
When registering the keyfob ID, perform only one procedure to simultaneously register both ID (IMMOBI-
LIZER ID and keyfob ID).
Work Procedure
INFOID:0000000006445190
1.
STEP 1
Close all doors.
>> GO TO 2.
2.
STEP 2
Operate lock using the driver side door lock and unlock switch.
>> GO TO 3.
3.
STEP 3
1.
Remove and insert the key into the ignition key 6 times within 10seconds (turning
the key switch from OFF to ON counts as 1 time).
2.
Hazard warning lamp blinks(2 times).
NOTE:
On the sixth key insertion, keep the key in the cylinder with the key switch ON.
Does the hazard lamp blink?
YES
>> GO TO 4.
NO
>> GO TO 1.
4.
STEP 4
Within 3 seconds after the hazard lamp blinks, turn ignition switch to the ACC position
and operate lock using the driver side door lock and unlock switch.
>> GO TO 5.
5.
STEP 5
1.
Press the lock or unlock button of the keyfob to be added.
2.
All doors unlock simultaneously.
3.
Hazard warning lamp blinks(2 times).
4.
Key ID is registered.
Is key ID registered?
YES-1 >> When adding a keyfob: GO TO 6.
YES-2 >> When ending registration: GO TO 8.
NO
>> GO TO 1.
6.
STEP 6
Operate lock using the driver side door lock and unlock switch.
>> GO TO 7.
7.
STEP 7
1.
Press the lock or unlock button of the keyfob to be added.
2.
All doors unlock simultaneously.
3.
Hazard warning lamp blinks(2 times).
4.
Key ID is registered.
DLK-382
< BASIC INSPECTION >
[TYPE 3]
KEYFOB ID REGISTRATION
Is key ID registered?
YES-1 >> When adding a keyfob: GO TO 6.
YES-2 >> When ending registration: GO TO 8.
NO
>> GO TO 6.
8.
STEP 8
Open the front door driver side.
>> REGISTRATION END
BACK DOOR OPENER ACTUATOR
DLK-383
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 3]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DTC/CIRCUIT DIAGNOSIS
BACK DOOR OPENER ACTUATOR
Diagnosis Procedure
INFOID:0000000006607730
1.
CHECK BACK DOOR OPENER ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect back door opener assembly connector.
3.
Check voltage between back door opener assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK BACK DOOR OPENER ACTUATOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and back door opener assembly harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK BACK DOOR OPENER ACTUATOR GROUND CIRCUIT
Check continuity between back door opener assembly harness connector and ground.
Is the inspection normal?
YES
>> Replace back door opener assembly.
NO
>> Repair or replace harness.
(+)
(–)
Condition
Voltage
(Approx.)
Back door opener assembly
Connector
Terminal
D106
1
Ground
Back opener
switch
ON
12 V
BCM
Back door opener assembly
Continuity
Connector
Terminal
Connector
Terminal
M65
50
D106
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M65
50
Not existed
Back door opener assembly
Ground
Continuity
Connector
Terminal
D106
2
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст