Juke F15 (2012 year). Service Repair Manual — part 255
DOOR CABLE
HAC-335
< REMOVAL AND INSTALLATION >
[TYPE 5]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
MODE DOOR CABLE : Removal and Installation
INFOID:0000000006706121
REMOVAL
1.
Disconnect mode door cable from A/C control. Refer to
2.
Remove glove box assembly. Refer to
IP-13, "Removal and Installation"
. (LHD models)
3.
Remove instrument panel RH. Refer to
IP-13, "Removal and Installation"
. (RHD models)
4.
Disconnect mode door cable from heater unit assembly as
shown by the arrow in the figure, and then remove mode door
cable.
INSTALLATION
Install in the reverse order of removal.
AIR MIX DOOR CABLE
AIR MIX DOOR CABLE : Removal and Installation
INFOID:0000000006706123
REMOVAL
1.
Disconnect air mix door cable from A/C control. Refer to
2.
Remove instrument panel LH. Refer to
IP-13, "Removal and Installation"
. (LHD models)
3.
Remove glove box assembly. Refer to
IP-13, "Removal and Installation"
. (RHD models)
4.
Disconnect air mix door cable from heater unit assembly as
shown by the arrow in the figure, and then remove air mix door
cable.
INSTALLATION
Install in the reverse order of removal.
JMIIA1029ZZ
JMIIA1028ZZ
HRN-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
HRN
A
B
HRN
N
O
P
CONTENTS
HORN
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ...
HORN . . . . . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
HORN . . . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
HRN-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006626414
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
The vehicle may be equipped with a passenger air bag deactivation switch. Because no rear seat exists where
a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a
rear-facing child restraint can be used in the front passenger seat. The switch is located in the center of the
instrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag is
enabled and could inflate for certain types of collision. When the switch is turned to the OFF position, the pas-
senger air bag is disabled and will not inflate. A passenger air bag OFF indicator on the instrument panel lights
up when the passenger air bag is switched OFF. The driver air bag always remains enabled and is not affected
by the passenger air bag deactivation switch.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
• The vehicle may be equipped with a passenger air bag deactivation switch which can be operated by
the customer. When the passenger air bag is switched OFF, the passenger air bag is disabled and
will not inflate. When the passenger air bag is switched ON, the passenger air bag is enabled and
could inflate for certain types of collision. After SRS maintenance or repair, make sure the passenger
air bag deactivation switch is in the same position (ON or OFF) as when the vehicle arrived for ser-
vice.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
HORN
HRN-3
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
HRN
N
O
P
WIRING DIAGRAM
HORN
Wiring Diagram
INFOID:0000000006626406
For connector terminal arrangements, harness layouts, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to
GI-12, "Connector Information/Explanation of Option Abbreviation"
JCLWA4249GB
HRN-4
< REMOVAL AND INSTALLATION >
HORN
REMOVAL AND INSTALLATION
HORN
Exploded View
INFOID:0000000006695797
WITHOUT VEHICLE SECURITY SYSTEM
WITH VEHICLE SECURITY SYSTEM
Removal and Installation
INFOID:0000000006626407
REMOVAL
Without Vehicle Security System
1.
Remove the front center grille and front side grille (LH/RH). Refer to
EXT-18, "Removal and Installation"
2.
Disconnect the horn (high and low) connectors.
1.
Horn high
2.
Horn low
3.
Horn bracket
JMLIA1192ZZ
1.
Horn low
2.
Horn bracket
JMLIA1500ZZ
HORN
HRN-5
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
HRN
N
O
P
3.
Remove the horn mounting bolts (A). Remove the horn high (1)
and horn low (2).
4.
Remove harness fixing clip from horn bracket.
5.
Remove horn bracket mounting bolts (LH/RH). Remove horn
bracket (1) from radiator core support upper.
With Vehicle Security System
1.
Remove the front center grille and front side grille (LH/RH). Refer to
EXT-18, "Removal and Installation"
2.
Disconnect the horn low connectors.
3.
Remove the horn mounting bolt (A). Remove the horn low (1).
4.
Remove harness fixing clip from horn bracket.
5.
Remove horn bracket mounting bolts (LH/RH). Remove horn
bracket (1) from radiator core support upper.
INSTALLATION
Install in the reverse order of removal.
: Harness fixing clip
JMLIA1227ZZ
JMLIA1228ZZ
: Harness fixing clip
JMLIA1501ZZ
JMLIA1502ZZ
INL-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
INL
A
B
INL
N
O
P
CONTENTS
INTERIOR LIGHTING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect . . . . . . . . .....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
INTERIOR LIGHTING SYSTEM . . . . . . . . ..
INTERIOR LIGHTING SYSTEM : Component
Parts Location . . . . . . . . . . . . . . ...
INTERIOR LIGHTING SYSTEM :
Component Description . . . . . . . . . . ....
SYSTEM . . . . . . . . . . . . . . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM :
System Diagram . . . . . . . . . . . . . ....
INTERIOR ROOM LAMP CONTROL SYSTEM :
System Description . . . . . . . . . . . . ...
INTERIOR ROOM LAMP BATTERY SAVER SYS-
TEM . . . . . . . . . . . . . . . . . . . ..
INTERIOR ROOM LAMP BATTERY SAVER
SYSTEM : System Diagram . . . . . . . . . ..
INTERIOR ROOM LAMP BATTERY SAVER
SYSTEM : System Description . . . . . . . .....
ILLUMINATION CONTROL SYSTEM . . . . . .....
ILLUMINATION CONTROL SYSTEM : System
Diagram . . . . . . . . . . . . . . . . .....
ILLUMINATION CONTROL SYSTEM : System
Description . . . . . . . . . . . . . . . ....
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
GENT KEY SYSTEM) . . . . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
INT LAMP . . . . . . . . . . . . . . . . ...
INT LAMP : CONSULT-III Function (BCM - INT
LAMP) . . . . . . . . . . . . . . . . . ..
BATTERY SAVER . . . . . . . . . . . . . .
BATTERY SAVER : CONSULT-III Function (BCM
- BATTERY SAVER) . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
TELLIGENT KEY SYSTEM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
INT LAMP . . . . . . . . . . . . . . . . ...
INT LAMP : CONSULT-III Function (BCM - INT
LAMP) . . . . . . . . . . . . . . . . . ..
BATTERY SAVER . . . . . . . . . . . . . .
BATTERY SAVER : CONSULT-III Function (BCM
- BATTERY SAVER) . . . . . . . . . . . ...
ECU DIAGNOSIS INFORMATION . . . ..
BCM . . . . . . . . . . . . . . . . ...
WITH INTELLIGENT KEY . . . . . . . . . . .
WITH INTELLIGENT KEY : List of ECU Reference
.
WITHOUT INTELLIGENT KEY . . . . . . . . ..
WITHOUT INTELLIGENT KEY : List of ECU Ref-
erence . . . . . . . . . . . . . . . . . ..
WIRING DIAGRAM . . . . . . . . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM
...
INL-2
ILLUMINATION . . . . . . . . . . . . ..
Wiring Diagram . . . . . . . . . . . . . ...
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORKFLOW . . .
Work Flow . . . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
INTERIOR ROOM LAMP POWER SUPPLY
CIRCUIT . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
INTERIOR ROOM LAMP CONTROL CIRCUIT
...
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
LUGGAGE ROOM LAMP CIRCUIT . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
PUSH-BUTTON IGNITION SWITCH ILLUMI-
NATION CIRCUIT . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . .
INTERIOR LIGHTING SYSTEM SYMPTOMS ...
Symptom Table . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ..
MAP LAMP . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
LUGGAGE ROOM LAMP . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
PRECAUTIONS
INL-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006753029
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
The vehicle may be equipped with a passenger air bag deactivation switch. Because no rear seat exists where
a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a
rear-facing child restraint can be used in the front passenger seat. The switch is located in the center of the
instrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag is
enabled and could inflate for certain types of collision. When the switch is turned to the OFF position, the pas-
senger air bag is disabled and will not inflate. A passenger air bag OFF indicator on the instrument panel lights
up when the passenger air bag is switched OFF. The driver air bag always remains enabled and is not affected
by the passenger air bag deactivation switch.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
• The vehicle may be equipped with a passenger air bag deactivation switch which can be operated by
the customer. When the passenger air bag is switched OFF, the passenger air bag is disabled and
will not inflate. When the passenger air bag is switched ON, the passenger air bag is enabled and
could inflate for certain types of collision. After SRS maintenance or repair, make sure the passenger
air bag deactivation switch is in the same position (ON or OFF) as when the vehicle arrived for ser-
vice.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000006478930
NOTE:
• Before removing and installing any control units, first turn the ignition switch to the LOCK position, then dis-
connect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
INL-4
< PRECAUTION >
PRECAUTIONS
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
COMPONENT PARTS
INL-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SYSTEM DESCRIPTION
COMPONENT PARTS
INTERIOR LIGHTING SYSTEM
INTERIOR LIGHTING SYSTEM : Component Parts Location
INFOID:0000000006646637
INTERIOR LIGHTING SYSTEM : Component Description
INFOID:0000000006482903
1.
2.
BCM
Refer to
SYSTEM : Component Parts Loca-
tion"
3.
Door lock and unlock switch
4.
Front door request switch (driver
side)
5.
Front door lock assembly (driver
side) ( unlock sensor)
6.
Door switch
7.
Luggage room lamp
8.
Back door switch
9.
Light & rain sensor
10. Remote keyless entry receiver
11.
Map lamp
12. Push-button ignition switch
13. Key switch
14. Combination meter
JMLIA1404ZZ
Part
Description
BCM
Controls the interior lighting system.
IPDM E/R
Controls the integrated relay according to the request signal from BCM (via CAN com-
munication).
Remote keyless entry receiver
Receives the lock/unlock signal form Keyfob.
Combination switch
(Lighting & turn signal switch)
Refer to
BCS-9, "COMBINATION SWITCH READING SYSTEM : System Description"
.
• Door lock and unlock switch
• Door request switch
Inputs the lock/unlock signal to BCM.
Door switch
Inputs the door switch signal to BCM.
Back door switch
Inputs the back door switch signal to BCM.
Unlock sensor
Detects door lock condition of driver side door.
Light & rain sensor
Refer to
EXL-8, "Component Description"
.
INL-6
< SYSTEM DESCRIPTION >
SYSTEM
SYSTEM
INTERIOR ROOM LAMP CONTROL SYSTEM
INTERIOR ROOM LAMP CONTROL SYSTEM : System Diagram
INFOID:0000000006482904
INTERIOR ROOM LAMP CONTROL SYSTEM : System Description
INFOID:0000000006482905
OUTLINE
• Interior room lamps* are controlled by interior room lamp timer control function of BCM.
*: Map lamp (when map lamp switch is in DOOR position).
• Luggage room lamp is controlled by luggage room lamp control function of BCM.
• Push-button ignition switch illumination is controlled by the push-button ignition switch illumination control
function of BCM.(With Intelligent Key)
INTERIOR ROOM LAMP TIMER CONTROL
Interior Room Lamp Timer Basic Operation
• The interior room lamp turns ON and OFF (gradual brightening and dimming) by the interior room lamp
timer.
JMLIA1483GB
JPLIA0093GB
SYSTEM
INL-7
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
• BCM judges the vehicle condition with the following items. It activates the interior room lamp timer.
- Ignition switch status
*1
- Door switch signal (except back door)
- Door lock/unlock signal (Remote keyless entry receiver, each door request switch
*1
, door lock and unlock
switch)
- Key switch signal
*2
*1
:With Intelligent Key
*2
:Without Intelligent Key
NOTE:
Each function of interior room lamp timer can be set by CONSULT-III. Refer to
SULT-III Function (BCM - INT LAMP)"
Interior Room Lamp ON Operation
• BCM always turns the interior room lamp ON when any door opens except back door.
• BCM activates the interior room lamp timer in any of the following conditions to turn the interior room lamp
ON for a period of time.
- Status of all doors except back door changes from open to close
- Ignition switch is turned ON
→
OFF
- Door unlock signal is detected when all doors close except back door with ignition switch OFF
NOTE:
The timer restarts if new condition is input during the timer operating time.
Interior Room Lamp OFF Operation
BCM stops the timer in any of the following conditions to turn the interior room lamp OFF.
• The timer operating time is expired
• Ignition switch is turned OFF
→
ACC/ON
• Door lock signal is detected with all doors close except back door.
LUGGAGE ROOM LAMP CONTROL
BCM turns luggage room lamp ON when the following condition is detected.
• Back door switch is ON
BCM turns luggage room lamp OFF when the following condition is detected.
• Back door switch is OFF
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CONTROL (WITH INTELLIGENT KEY)
Push-button Ignition Switch Illumination Basic Operation
BCM provides the power supply to turn the push-button ignition switch illumination ON.
Push-button Ignition Switch Illumination ON Operation
BCM turns the push-button ignition switch illumination ON in the following conditions.
• Ignition switch ON
• Any of the following conditions with ignition switch OFF/ACC
- Engine start permission is entered
- Driver side door is LOCK
→
UNLOCK
- Driver side door is open
Push-button Ignition Switch Illumination OFF Operation
BCM turns the push-button ignition switch illumination OFF in any of the following conditions.
• The push-button ignition switch illumination ON conditions do not satisfy.
• Any of the following conditions with ignition switch OFF.
- The push-button ignition switch illumination ON conditions do not change (15 seconds after the ignition
switch OFF)
- Driver side door is UNLOCK
→
LOCK
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM
INL-8
< SYSTEM DESCRIPTION >
SYSTEM
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM : System Diagram
INFOID:0000000006482906
INTERIOR ROOM LAMP BATTERY SAVER SYSTEM : System Description
INFOID:0000000006482907
OUTLINE
• Interior room lamp battery saver is controlled by BCM.
• BCM turns applicable lamps OFF depending on the vehicle condition. This function prevents the battery
from over-discharging if the driver neglects turning OFF the lamps.
Applicable lamps
• Map lamp
• Luggage room lamp
INTERIOR ROOM LAMP BATTERY SAVER FUNCTION
• When the ignition switch is turned to other position than ON, BCM operates the timer for a period of time to
cut the interior room lamp power supply.
• BCM restarts the timer when any of the following signals changes while operating the timer.
- Ignition switch status
*1
- Key switch status
*2
- Door switch signal (ALL)
- Door lock/unlock signal (remote keyless entry receiver, each door request switch
*1
, door lock and unlock
switch, unlock sensor)
• BCM provides the interior room lamp power supply continuously when the ignition switch position is ON.
*1
:With Intelligent Key
*2
:Without Intelligent Key
NOTE:
Each function of interior room lamp battery saver can be set by CONSULT-III. Refer to
SAVER : CONSULT-III Function (BCM - BATTERY SAVER)"
ILLUMINATION CONTROL SYSTEM
JMLIA1489GB
SYSTEM
INL-9
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ILLUMINATION CONTROL SYSTEM : System Diagram
INFOID:0000000006482908
ILLUMINATION CONTROL SYSTEM : System Description
INFOID:0000000006482909
OUTLINE
Each illumination lamp is controlled by each function of BCM and IPDM E/R.
Control by BCM
• Combination switch reading function
• Headlamp control function
Control by IPDM E/R
• Relay control function
Control by combination meter
• Meter illumination control function (Refer to
MWI-11, "SPEEDOMETER : System Description"
ILLUMINATION CONTROL
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits position light request signal to IPDM E/R and combination meter according to tail lamp ON
condition.
Tail lamp ON condition
- Lighting switch 1ST
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment (With auto light system)
• IPDM E/R turns the integrated tail lamp relay ON according to position light request signal. It provides the
power supply to each illumination lamp.
• Combination meter enters in the nighttime mode according to position light request signal. Under the night-
time mode the combination meter controls the illuminance by controlling the each illumination lamp (ground
side).
JSLIA0087GB
INL-10
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000006482912
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
*: This item is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
—
AIR CONDITONER*
×
×
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
IVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk lid open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст