Juke F15 (2012 year). Service Repair Manual — part 10
BCS-16
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM
Wake-up condition
Wake-up condition
• Receiving the sleep-ready signal (Not-ready) from any units
• Push-button ignition switch (push switch): OFF
→
ON
• Hazard switch: ON
• HI BEAM switch: OFF
→
ON, ON
→
OFF
• PASSING switch: OFF
→
ON, ON
→
OFF
• HEADLAMP 1 switch: OFF
→
ON, ON
→
OFF
• HEADLAMP 2 switch: OFF
→
ON, ON
→
OFF
• TAIL LAMP switch: OFF
→
ON
• FR FOG switch: OFF
→
ON, ON
→
OFF
• RR FOG switch: OFF
→
ON
• TURN RH: OFF
→
ON, ON
→
OFF
• TURN LH: OFF
→
ON, ON
→
OFF
• Driver door switch: OFF
→
ON, ON
→
OFF
• Passenger door switch: OFF
→
ON, ON
→
OFF
• Rear RH door switch: OFF
→
ON, ON
→
OFF
• Rear LH door switch: OFF
→
ON, ON
→
OFF
• Back door switch: OFF
→
ON, ON
→
OFF
• Driver door request switch: OFF
→
ON
• Passenger door request switch: OFF
→
ON
• Back door request switch: OFF
→
ON
• Back door opener switch: OFF
→
ON
• Stop lamp switch: ON
• Door lock and unlock switch: NEUTRAL
→
LOCK, NEUTRAL
→
UNLOCK
• Remote keyless entry receiver communication: Receiving
• Front door lock assembly (driver side) (unlock sensor):
OFF
→
ON, ON
→
OFF
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-17
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000006598022
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
• *1: This item is displayed, but not used.
• *2: For models with automatic A/C, this diagnosis mode is not used.
FREEZE FRAME DATA (FFD)
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
• Automatic A/C
• Manual A/C
AIR CONDITONER
×
×
*
2
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
—
RETAINED PWR*
1
×
Signal buffer system
SIGNAL BUFFER
×
×
BCS-18
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (With Super Lock)
INFOID:0000000006744609
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
WORK SUPPORT
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK” to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”.) to low power consumption mode
LOCK
Power supply position is “LOCK” (Ignition switch OFF with steer-
ing is locked.)
OFF
Power supply position is “OFF” (Ignition switch OFF with steering
is unlocked.)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-19
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: P range interlock door lock can be selected for M/T models, but automatic door lock/unlock function does not operate.
DATA MONITOR
ACTIVE TEST
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function mode can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 10 km/h (6 MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other than
the P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function mode can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to OFF
• MODE 2*: All doors are unlocked when shifting the selector lever from any position other than
the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON to
OFF
• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position other
than the P to P position
• MODE 5: This item is displayed, but cannot be monitored
• MODE 6: This item is displayed, but cannot be monitored
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function mode can be selected from the following in this mode
• Off: Non-operational
• Unlock Only: Door unlock operation only
• Lock Only: Door lock operation only
• Lock/Unlock: Lock and unlock operation
Monitor Item
Contents
REQ SW-DR
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
Indicated [On/Off] condition of door request switch (passenger side)
REQ SW-BD/TR
Indicated [On/Off] condition of back door request switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
Indicated [On/Off] condition of back door switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
KEY CYL LK-SW
NOTE:
This item is displayed, but cannot be monitored
KEY CYL UN-SW
NOTE:
This item is displayed, but cannot be monitored
SHOCK SENSOR
Indicates [NOMAL/ON/OFF] condition of circuit between BCM and air bag diagnosis sensor unit
• NORMAL: Ignition switch ON. (BCM is receiving normal condition signal from air bag diagnosis sensor
unit.)
• ON: During the receiving of air bag signal from air bag diagnosis sensor unit
• OFF: After the receiving of air bag signal from air bag diagnosis sensor unit
BCS-20
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*: BD UNLK function does not operate.
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)
INFOID:0000000006744612
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
WORK SUPPORT
*: P range interlock door lock can be selected for M/T models, but automatic door lock/unlock function does not operate.
DATA MONITOR
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LOCK” on CONSULT-III screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen is
touched
• The back door lock actuator is unlocked when “BD UNLK” on CONSULT- III screen is touched*
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT-III screen is touched
SUPER LOCK
This test is able to check super lock actuator operation
• The all door lock actuators are set when “LOCK” on CONSULT-III screen is touched
• The all door lock actuators are released when “UNLOCK” on CONSULT-III screen is touched
DOOR LOCK IND
This test is able to check door lock status indicator operation
• On: Operate
• Off: Non-operation
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function mode can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 10 km/h (6 MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other than
the P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function mode can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to OFF
• MODE 2*: All doors are unlocked when shifting the selector lever from any position other than
the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON to
OFF
• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position other
than the P to P position
• MODE 5: This item is displayed, but cannot be monitored
• MODE 6: This item is displayed, but cannot be monitored
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function mode can be selected from the following in this mode
• Off: Non-operational
• Unlock Only: Door unlock operation only
• Lock Only: Door lock operation only
• Lock/Unlock: Lock and unlock operation
Monitor Item
Contents
REQ SW-DR
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
Indicated [On/Off] condition of door request switch (passenger side)
REQ SW-BD/TR
Indicated [On/Off] condition of back door request switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-21
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
*: BD UNLK function does not operate.
REAR WINDOW DEFOGGER
REAR WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)
INFOID:0000000006744623
Data monitor
ACTIVE TEST
BUZZER
BUZZER : CONSULT-III Function (BCM - BUZZER)
INFOID:0000000006744624
CONSULT-III APPLICATION ITEMS
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
Indicated [On/Off] condition of back door switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
KEY CYL LK-SW
NOTE:
This item is displayed, but cannot be monitored
KEY CYL UN-SW
NOTE:
This item is displayed, but cannot be monitored
SHOCK SENSOR
Indicates [NOMAL/ON/OFF] condition of circuit between BCM and air bag diagnosis sensor unit
• NORMAL: Ignition switch ON. (BCM is receiving normal condition signal from air bag diagnosis sensor
unit.)
• ON: During the receiving of air bag signal from air bag diagnosis sensor unit
• OFF: After the receiving of air bag signal from air bag diagnosis sensor unit
Monitor Item
Contents
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LOCK” on CONSULT-III screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen is
touched
• The back door lock actuator is unlocked when “BD UNLK” on CONSULT- III screen is touched*
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT-III screen is touched
SUPER LOCK
NOTE:
This item is displayed, but cannot be monitored
DOOR LOCK IND
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Description
REAR DEF SW
Displays “Press (ON)/other (OFF)” status determined with the rear window defogger switch.
PUSH SW
Indicates [ON/OFF] condition of push switch.
Test Item
Description
REAR DEFOGGER
Give a drive signal to the rear window defogger relay to activate it.
Test item
Diagnosis mode
Description
BUZZER
Data Monitor
Displays BCM input data in real time.
Active Test
Operation of electrical loads can be checked by sending driving signal to them.
BCS-22
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
DATA MONITOR
ACTIVE TEST
INT LAMP
INT LAMP : CONSULT-III Function (BCM - INT LAMP)
INFOID:0000000006744619
WORK SUPPORT
Display item
[Unit]
Description
PUSH SW
[On/Off]
Status of push-button ignition switch judged by BCM.
UNLK SEN-DR
[On/Off]
Status of unlock sensor judged by BCM.
VEH SPEED 1
[km/h]
Value of vehicle speed signal received from combination meter with CAN communication line.
TAIL LAMP SW
[On/Off]
Status of lighting switch judged by BCM using the combination switch readout function.
FR FOG SW
[On/Off]
Status of front fog lamp switch judged by BCM using the combination switch readout function.
DOOR SW-DR
[On/Off]
Status of driver side door switch judged by BCM.
CDL LOCK SW
[On/Off]
Status of door lock unlock switch judged by BCM.
Display item
[Unit]
Description
KEY REMINDER WARN
The key warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM
The light warning chime operation can be checked by operating the relevant function (On/Off).
JPLIA0093GB
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 2
7.5 sec.
Sets the interior room lamp ON time. (Timer operating time)
MODE 3
15 sec.
MODE 4*
30 sec.
SET I/L D-UNLCK INTCON
On*
With the interior room lamp timer function
Off
Without the interior room lamp timer function
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-23
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: Factory setting
DATA MONITOR
ROOM LAMP ON TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual brightening time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
0 sec.
ROOM LAMP OFF TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual dimming time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
0 sec.
R LAMP TIMER LOGIC SET
MODE 1*
Interior room lamp timer activates with synchronizing all doors.
MODE 2
Interior room lamp timer activates with synchronizing the driver door
only.
Service item
Setting item
Setting
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from request switch (passenger side)
REQ SW-RR
[On/Off]
NOTE:
The item is indicated, but not monitored.
REQ SW-RL
[On/Off]
PUSH SW
[On/Off]
Push switch status received from Intelligent Key unit by CAN communication
UNLK SEN -DR
[On/Off]
Driver door unlock status input from unlock sensor
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
DOOR SW- BK
[On/Off]
The switch status input from back door switch
CDL LOCK SW
[On/Off]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[On/Off]
Unlock switch status input from door lock and unlock switch
TRNK/HAT MNTR
[On/Off]
NOTE:
The item is indicated, but not monitored
KEY CYL LK-SW
[On/Off]
NOTE:
The item is indicated, but not monitored
KEY CYL UN-SW
[On/Off]
NOTE:
The item is indicated, but not monitored
BCS-24
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000006744617
WORK SUPPORT
*
1
: For models is without auto light system, this item is displayed but work support is not operated.
*
2
: Factory setting
DATA MONITOR
RKE-LOCK
[On/Off]
Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off]
Unlock signal status received from remote keyless entry receiver
Monitor item
[Unit]
Description
Test item
Operation
Description
INT LAMP
On
Outputs the interior room lamp control signal to turn the interior room lamps ON.
[Map lamp, room lamp (when applicable lamps switch is in DOOR position.)]
Off
Stops the interior room lamp control signal to turn the interior room lamps.
Service item
Setting item
Setting
CUSTOM A/LIGHT SET-
TING*
1
MODE 1*
2
Normal
MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal opera-
tion.)
MODE 3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE 4
Without twilight ON custom & less sensitive setting than normal setting (Turns ON
later than normal operation.)
BATTERY SAVER SET
On*
2
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
HEAD LIGHT TIMER
MODE 1
10 sec.
Sets follow me home function activating time
MODE 2*
2
30 sec.
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
The engine status received from ECM via CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from combination meter via CAN communi-
cation
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-25
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: For models without auto light system, this is not displayed.
ACTIVE TEST
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW*
[On/Off]
FR FOG SW
[On/Off]
RR FOG SW
[On/Off]
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
DOOR SW-BK
[On/Off]
The switch status input from back door switch
OPTICAL SENSOR*
[On/Off/NG]
The sensor condition received from light & rain sensor
OPTI SEN (DTCT)
[V]
NOTE:
The item is indicated, but not monitored
OPTI SEN (FILT)
[V]
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R via CAN commu-
nication to turn the tail lamp ON.
Off
Stops the tail lamp request signal transmission.
HEAD LAMP
Hi
Transmits the high beam request signal via CAN communication to turn
the headlamp (HI).
Lo
Transmits the low beam request signal via CAN communication to turn
the headlamp (LO).
Off
Stops the high & low beam request signal transmission.
FR FOG LAMP
On
Transmits the front fog lights request signal to IPDM E/R via CAN com-
munication to turn the front fog lamp ON.
Off
Stops the front fog lights request signal transmission.
BCS-26
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*: For models without daytime running light system, this item is not displayed.
WIPER
WIPER : CONSULT-III Function - WIPER
INFOID:0000000006744621
WORK SUPPORT
*1: The item is indicated, but not operated on model with rain sensor
*2: The item is indicated, but not operated on model without rain sensor
*3: Factory setting
DATA MONITOR
RR FOG LAMP
On
• Outputs voltage to turn the rear fog lamp ON.
• Transmits the rear fog lights request signal to combination meter via
CAN communication to turn the rear fog lamp indicator lamp ON.
Off
• Stops the voltage to turn the rear fog lamp OFF.
• Stops the rear fog lamp status signal transmission.
DAYTIME RUNNING LIGHT*
On
Transmits the daytime running light request signal via CAN communica-
tion to turn the parking, license plate and tail lamps ON.
Off
Stop the daytime running light request signal transmission.
Test item
Operation
Description
Service item
Setting item
Description
WIPER SPEED
SETTING*1
On*3
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and
wiper intermittent dial position)
The setting of front wiper
INT operation can be
changed
Off
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial
position)
RAIN SEN WIP
FUNC SET*2
On*3
With light & rain sensor
(Front wiper intermittent time linked with the light & rain sensor,
vehicle speed, and AUTO dial position)
The setting of front wiper
AUTO operation can be
changed
Off
Without light & rain sensor
(Front wiper intermittent time linked with the vehicle speed and
AUTO dial position)
Monitor Item
[Unit]
Description
PUSH SW
[Off/On]
The switch status input from push-button ignition switch
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from combination meter via CAN com-
munication
FR WIPER HI
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
FR WIPER LOW
[Off/On]
FR WASHER SW
[Off/On]
FR WIPER INT
[Off/On]
FR WIPER STOP
[Off/On]
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN
communication.
INT VOLUME
[1
−
7]
Status of each switch judged by BCM using the combination switch reading function
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-27
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000006744618
WORK SUPPORT
*: Factory setting
DATA MONITOR
RR WIPER ON
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
RR WIPER INT
[Off/On]
RR WASHER SW
[Off/On]
RR WIPER STOP
[Off/On]
Rear wiper motor (stop position) status input from the rear wiper motor
H/L WASH SW
[Off/On]
NOTE:
The item is indicated, but not monitored
RAIN SENSOR
[OFF/LOW/HIGH/SPLASH/NG]
Request signal from light & rain sensor detected by BCM is displayed
Monitor Item
[Unit]
Description
Test item
Operation
Description
FR WIPER
Hi
Transmits the front wiper request signal (HI) to IPDM E/R via CAN communication to op-
erate the front wiper HI operation.
Lo
Transmits the front wiper request signal (LO) to IPDM E/R via CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R via CAN communication to
operate the front wiper INT operation.
Off
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
On
Output the voltage to operate the rear wiper motor.
Off
Stops the voltage to stop the rear wiper motor.
HEADLAMP WASH-
ER
On
Transmits the headlamp washer request signal to IPDM E/R via CAN communication to
operate the headlamp washer operation.
Service item
Setting item
Setting
HAZARD ANSWER
BACK
Lock Only
With locking only
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the door request switch
and Intelligent Key.
Unlk Only
With unlocking only
Lock&Unlk
*
With locking/unlocking
Off
Without the function
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from the request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from the request switch (passenger side)
PUSH SW
[On/Off]
The switch status input from the push-button ignition switch
BCS-28
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
AIR CONDITIONER
AIR CONDITIONER : CONSULT-III Function (BCM - AIR CONDITIONER) (Automatic
A/C 4WD Models)
INFOID:0000000006744625
DATA MONITOR
Display Item List
AIR CONDITIONER : CONSULT-III Function (BCM - AIR CONDITIONER) (Automatic
A/C 2WD Models)
INFOID:0000000006744626
DATA MONITOR
Display Item List
AIR CONDITIONER : CONSULT-III Function (BCM - AIR CONDITIONER) (Manual A/
C 4WD Models)
INFOID:0000000006744627
DATA MONITOR
Display item list
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
RKE-LOCK
[On/Off]
Lock signal status received from the remote keyless entry receiver
RKE-UNLOCK
[On/Off]
Unlock signal status received from the remote keyless entry receiver
RKE-PANIC
[On/Off]
NOTE:
The item is indicated, but not monitored
Monitor item
[Unit]
Description
Test item
Operation
Description
FLASHER
RH
Outputs the voltage to blink the right side turn signal lamps.
LH
Outputs the voltage to blink the left side turn signal lamps.
Off
Stops the voltage to turn the turn signal lamps OFF.
Monitor Item [Unit]
Contents
FAN ON SIG
[On/Off]
Displays the blower fan status as jugged from the A/C auto amp.
AIR COND SW
[On/Off]
Displays [COMP (On)/COMP (Off)] status as judged from the A/C auto amp.
Monitor Item [Unit]
Contents
FAN ON SIG
[On/Off]
Displays the blower fan status as jugged from the A/C auto amp.
AIR COND SW
[On/Off]
Displays [COMP (On)/COMP (Off)] status as judged from the A/C auto amp.
Monitor Item [Unit]
Contents
FAN ON SIG
[On/Off]
Displays blower motor status as judged from blower fan ON signal.
AIR COND SW
[On/Off]
Displays A/C switch status as judged from A/C switch signal.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-29
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
AIR CONDITIONER : CONSULT-III Function (BCM - AIR CONDITIONER) (Manual A/
C 2WD Models)
INFOID:0000000006744628
DATA MONITOR
Display item list
ACTIVE TEST
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) (With Super
Lock)
INFOID:0000000006744610
WORK SUPPORT
THERMO AMP
[On/Off]
Displays thermo control amp. status as judged from thermo control amp. signal.
IGN SW
[On/Off]
Displays ignition switch position status as judged form ignition switch signal.
Monitor Item [Unit]
Contents
Test item
Operation
Description
A/C INDICATOR
On
A/C indicator is turned ON.
Off
A/C indicator is turned OFF.
Monitor Item [Unit]
Contents
FAN ON SIG
[On/Off]
Displays blower motor status as judged from blower fan ON signal.
AIR COND SW
[On/Off]
Displays A/C switch status as judged from A/C switch signal.
THERMO AMP
[On/Off]
Displays thermo control amp. status as judged from thermo control amp. signal.
IGN SW
[On/Off]
Displays ignition switch position status as judged form ignition switch signal.
Test item
Operation
Description
A/C INDICATOR
On
A/C indicator is turned ON.
Off
A/C indicator is turned OFF.
Monitor item
Description
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
TRUNK/GLASS HATCH OPEN
NOTE:
This item is displayed, but cannot be monitored
PANIC ALARM SET
NOTE:
This item is displayed, but cannot be monitored
TRUNK OPEN DELAY
NOTE:
This item is displayed, but cannot be monitored
LO- BATT OF KEY FOB WARN
Intelligent Key low battery warning mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
BCS-30
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
SELF-DIAG RESULT
DATA MONITOR
ANTI KEY LOCK IN FUNCTI
Key reminder function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
HAZARD ANSWER BACK
Hazard reminder function mode by door request switch and Intelligent Key button can be se-
lected from the following with this mode
• Lock Only: Door lock operation only
• Unlock Only: Door unlock operation only
• Lock/Unlock: Lock and unlock operation
• Off: Non-operation
ANS BACK I-KEY LOCK
Buzzer reminder function (lock operation) mode by door request switch can be selected from
the following with this mode
• Horn Chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• Off: Non-operation
ANS BACK I-KEY UNLOCK
Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operation with this mode
• On: Operate
• Off: Non-operation
SHORT CRANKING OUTPUT
Starter motor can operate during the times below
• 70 msec
• 100 msec
• 200 msec
CONFIRM KEY FOB ID
It can be checked whether Intelligent Key ID code is registered or not in this mode
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
ANSWER BACK FUNCTION
Buzzer reminder function mode by Intelligent Key button can be selected from the following
with this mode
• On: Operate
• Off: Non-operation
TAKE OUT FROM WIN WARN SET
NOTE:
This item is indicated, but not used
RETRACTABLE MIRROR SET
Auto retractable door mirror function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
SFT PN/N SW
Indicates [On/Off] condition of P or N position
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-31
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
S/L -LOCK
Indicates [On/Off] condition of steering lock unit (LOCK)
S/L -UNLOCK
Indicates [On/Off] condition of steering lock unit (UNLOCK)
S/L RELAY -F/B
Indicates [On/Off] condition of steering lock relay
UNLK SEN -DR
Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
DETE SW -IPDM
Indicates [On/Off] condition of P position
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
SFT P -MET
Indicates [On/Off] condition of P position
SFT N -MET
Indicates [On/Off] condition of N position
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
S/L LOCK-IPDM
Indicates [On/Off] condition of steering lock unit (LOCK)
S/L UNLK-IPDM
Indicates [On/Off] condition of steering lock unit (UNLOCK)
S/L RELAY-REQ
Indicates [On/Off] condition of steering lock relay
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver side door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status
ID OK FLAG
Indicates [Set/Reset] condition of key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT-III screen is touched
• Key: Key warning chime sounds when CONSULT-III screen is touched
• Knob: OFF position warning chime sounds when CONSULT-III screen is touched
• Off: Non-operation
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст