Juke F15 (2012 year). Service Repair Manual — part 105
P183C DECEL G SENSOR
DLN-69
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P183C DECEL G SENSOR
DTC Logic
INFOID:0000000006360043
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1minute.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183C” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006360044
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “ABS”.
Is any DTCs detected?
YES
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT-III
1.
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2.
Start the engine and drive vehicle at 30 km/h (19 MPH) or more.
3.
Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
BRC-212, "Diagnosis Procedure"
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check 4WD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC
“P183C” is detected, Replace 4WD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P183C
DECEL G SENSOR
Malfunction is detected in decel G sen-
sor signal that is output from ABS actua-
tor and electric unit (control unit) through
CAN communication.
• ABS actuator and electric unit (control
unit)
• Yaw rate/side/decel G sensor
• 4WD control module
• CAN communication line
DLN-70
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P183D SIDE G SENSOR
P183D SIDE G SENSOR
DTC Logic
INFOID:0000000006360045
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1minute.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183D” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006360046
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “ABS”.
Is any DTCs detected?
YES
>> Check the DTCs. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT-III
1.
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2.
Start the engine and drive vehicle at 30 km/h (19 MPH) or more.
3.
Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
BRC-212, "Diagnosis Procedure"
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check 4WD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC
“P183D” is detected, Replace 4WD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P183D
SIDE G SENSOR
Malfunction is detected in side G sensor
signal that is output from ABS actuator
and electric unit (control unit) through
CAN communication.
• ABS actuator and electric unit (control
unit)
• Yaw rate/side/decel G sensor
• 4WD control module
• CAN communication line
P183E YAW RATE SENSOR
DLN-71
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P183E YAW RATE SENSOR
DTC Logic
INFOID:0000000006360048
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1minute.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183E” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006360049
1.
PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “ABS”.
Is any DTCs detected?
YES
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT-III
1.
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2.
Start the engine and drive vehicle at 30 km/h (19 MPH) or more.
3.
Check that ABS warning lamp turns OFF.
Does ABS warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
BRC-212, "Diagnosis Procedure"
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check 4WD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC
“P183E” is detected, Replace 4WD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P183E
YAWRATE SENSOR
Malfunction is detected in yaw rate sen-
sor signal that is output from ABS actua-
tor and electric unit (control unit) through
CAN communication.
• ABS actuator and electric unit (control
unit)
• Yaw rate/side/decel G sensor
• 4WD control module
• CAN communication line
DLN-72
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P183F GEAR POSITION SIGNAL
P183F GEAR POSITION SIGNAL
DTC Logic
INFOID:0000000006360050
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1minute.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P183F” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006360051
1.
PERFORM TCM SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “TRANSMISSION”.
Is any DTCs detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT-III
1.
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2.
Start the engine and drive vehicle at 30 km/h (19 MPH) or more.
3.
Check that A/T CHECK indictor lamp turns OFF.
Does A/T CHECK indicator lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check 4WD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC
“P183F” is detected, Replace 4WD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P183F
GEAR POSI SIGNAL
Malfunction is detected in current gear
position signal that is output from TCM
through CAN communication.
• CVT sensor
• TCM
• 4WD control module
• CAN communication line
P1840 OUTPUT SPEED SIGNAL
DLN-73
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P1840 OUTPUT SPEED SIGNAL
DTC Logic
INFOID:0000000006360052
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1minute.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1840” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006360053
1.
PERFORM TCM SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “TRANSMISSION”.
Is any DTCs detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT-III
1.
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2.
Start the engine and drive vehicle at 30 km/h (19 MPH) or more.
3.
Check that A/T CHECK indictor lamp turns OFF.
Does A/T CHECK indicator lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check 4WD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC
“P1840” is detected, Replace 4WD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1840
OUTPUT SPEED SIGNAL
Malfunction is detected in output shaft
revolution signal that is output from TCM
through CAN communication.
• CVT sensor
• TCM
• 4WD control module
• CAN communication line
DLN-74
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
P1864 INPUT SPEED SIGNAL
P1864 INPUT SPEED SIGNAL
DTC Logic
INFOID:0000000006360054
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1minute.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1864” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006360055
1.
PERFORM TCM SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “TRANSMISSION”.
Is any DTCs detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT-III
1.
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2.
Start the engine and drive vehicle at 30 km/h (19 MPH) or more.
3.
Check that A/T CHECK indictor lamp turns OFF.
Does A/T CHECK indicator lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check 4WD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC
“P1864” is detected, Replace 4WD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1864
INPUT SPEED SIGNAL
Malfunction is detected in input shaft
revolution signal that is output from TCM
through CAN communication.
• CVT sensor
• TCM
• 4WD control module
• CAN communication line
P1865 GEAR RATIO SIGNAL
DLN-75
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
P1865 GEAR RATIO SIGNAL
DTC Logic
INFOID:0000000006360056
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1minute.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1865” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006360057
1.
PERFORM TCM SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “TRANSMISSION”.
Is any DTCs detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
ERASE SELF-DIAGNOSTIC RESULT
With CONSULT-III
1.
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
2.
Start the engine and drive vehicle at 30 km/h (19 MPH) or more.
3.
Check that A/T CHECK indictor lamp turns OFF.
Does A/T CHECK indicator lamp turn OFF?
YES
>> GO TO 3.
NO
>> Refer to
3.
CHECK TERMINALS AND HARNESS CONNECTORS
Check 4WD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?
YES
>> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC
“P1865” is detected, Replace 4WD control module. Refer to
DLN-91, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
P1865
GEAR RATIO
Malfunction is detected in CVT ratio sig-
nal that is output from TCM through CAN
communication.
• CVT sensor
• TCM
• 4WD control module
• CAN communication line
DLN-76
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
U1000 CAN COMM CIRCUIT
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000006359919
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit communicate data but selectively reads required data only.
DTC Logic
INFOID:0000000006359920
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Turn the ignition switch OFF to ON.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “U1000” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006359921
LAN-17, "Trouble Diagnosis Flow Chart"
DTC
Display item
Malfunction detected condition
Possible cause
U1000
CAN COMM CIRCUIT
4WD control module is not transmitting/
receiving CAN communication signal for
2 seconds or more.
• CAN communication error
• Malfunction of 4WD control module
U1010 CONTROL UNIT (CAN)
DLN-77
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
U1010 CONTROL UNIT (CAN)
Description
INFOID:0000000006359922
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit communicate data but selectively reads required data only.
DTC Logic
INFOID:0000000006359923
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
DTC REPRODUCTION PROCEDURE
With CONSULT-III
1.
Turn the ignition switch OFF to ON.
2.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “U1010” detected?
YES
>> Proceed to diagnosis procedure. Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006359924
1.
CHECK 4WD CONTROL MODULE
Check 4WD control module harness connector for disconnection and deformation.
Is the inspection result normal?
YES
>> Replace 4WD control module. Refer to
DLN-91, "Removal and Installation"
.
NO
>> Repair or replace error-detected parts.
DTC
Display item
Malfunction detected condition
Possible cause
U1010
CONTROL UNIT (CAN)
Detecting error during the initial diagno-
sis of CAN controller of 4WD control
module.
Internal malfunction of 4WD control
module
DLN-78
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000006359926
1.
CHECK 4WD CONTROL MODULE POWER SUPPLY (1)
1.
Turn the ignition switch OFF.
2.
Disconnect 4WD control module harness connector.
3.
Check the voltage between 4WD control module harness connector and ground.
4.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
5.
Check the voltage between 4WD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK 4WD CONTROL MODULE POWER SUPPLY (2)
1.
Turn the ignition switch OFF.
2.
Check the 10A fuse (#33).
3.
Check the harness for open or short between 4WD control module harness connector No.1 terminal and
10A (#33).
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit. Refer to
NO
>> Repair or replace error-detected parts.
3.
CHECK 4WD CONTROL MODULE POWER SUPPLY (3)
1.
Turn the ignition switch OFF.
2.
Check the voltage between 4WD control module harness connector and ground.
3.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
4.
Check the voltage between 4WD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4WD control module
—
Voltage
Connector
Terminal
B47
1
Ground
Battery voltage
4WD control module
—
Voltage
Connector
Terminal
B47
1
Ground
Battery voltage
4WD control module
—
Voltage
Connector
Terminal
B47
3
Ground
0 V
4WD control module
—
Voltage
Connector
Terminal
B47
3
Ground
Battery voltage
POWER SUPPLY AND GROUND CIRCUIT
DLN-79
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4.
CHECK 4WD CONTROL MODULE POWER SUPPLY (4)
1.
Turn the ignition switch OFF.
2.
Check the 10A fuse (#3).
3.
Check the harness for open or short between 4WD control module harness connector No.3 terminal and
10A (#3).
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for ignition power supply circuit. Refer to
NO
>> Repair or replace error-detected parts.
5.
CHECK 4WD SOLENOID POWER SUPPLY (1)
1.
Turn the ignition switch OFF.
2.
Disconnect 4WD control module harness connector.
3.
Check the voltage between 4WD control module harness connector and ground.
4.
Turn the ignition switch OFF to ON.
CAUTION:
Never start the engine.
5.
Check the voltage between 4WD control module harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
CHECK 4WD SOLENOID POWER SUPPLY (2)
1.
Turn the ignition switch OFF.
2.
Check the 10A fuse (#12).
3.
Check the harness for open or short between 4WD control module harness connector No.12 and the 10A
fuse (#12).
Is the inspection result normal?
YES
>> Perform the trouble the diagnosis for power supply circuit. Refer to
.
NO
>> Repair or replace error-detected parts.
7.
CHECK 4WD CONTROL MODULE GROUND
1.
Turn the ignition switch OFF.
2.
Check the continuity between 4WD control module harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace error-detected parts.
4WD control module
—
Voltage
Connector
Terminal
B47
12
Ground
Battery voltage
4WD control module
—
Voltage
Connector
Terminal
B47
12
Ground
Battery voltage
4WD control module
—
Continuity
Connector
Terminal
B47
10
Ground
Existed
11
DLN-80
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
4WD WARNING LAMP
4WD WARNING LAMP
Component Function Check
INFOID:0000000006359927
1.
CHECK 4WD WARNING LAMP FUNCTION
1.
Turn the ignition switch ON.
2.
Check that 4WD warning lamp turns on.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000006359928
1.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the error-detected parts.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 3.
3.
CHECK 4WD WARNING LAMP SIGNAL
With CONSULT-III
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check “WARNING LAMP” of CONSULT-III “DATA MONITOR” for “ALL MODE AWD/4WD”.
Does the item on “DATA MONITOR” indicate “On”?
YES
>> Perform the trouble diagnosis for combination meter power supply circuit. Refer to
"COMBINATION METER : Diagnosis Procedure"
.
NO
>> Replace 4WD control module. Refer to
DLN-91, "Removal and Installation"
.
4WD MODE INDICATOR LAMP (4WD-V)
DLN-81
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4WD MODE INDICATOR LAMP (4WD-V)
Component Function Check
INFOID:0000000006359929
1.
4WD MODE INDICATOR LAMP OPERATION CHECK
1.
Turn the ignition switch ON.
2.
Change 4WD mode switch to “4WD-V”.
3.
Check that 4WD mode indicator lamp (4WD-V) turns on.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000006359930
1.
CHECK 4WD WARNING LAMP
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
Does 4WD warning lamp turn ON?
YES
>> Proceed to
.
NO
>> GO TO 2.
2.
CHECK 4WD MODE SWITCH
Perform the trouble diagnosis for 4WD mode switch. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK 4WD MODE INDICATOR LAMP SIGNAL
With CONSULT-III
1.
Start the engine.
CAUTION:
Stop the vehicle.
2.
Change 4WD mode switch to “4WD-V” from “2WD”.
3.
Check “INDICATOR” of CONSULT-III “DATA MONITOR” for “ALL MODE AWD/4WD”.
Does the item on “DATA MONITOR” indicate “4WD-V”?
YES
>> GO TO 4.
NO
>> Replace 4WD control module. Refer to
DLN-91, "Removal and Installation"
.
4.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
Perform the trouble diagnosis for combination meter power supply circuit. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace the error-detected parts.
DLN-82
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
4WD MODE INDICATOR LAMP (4WD)
4WD MODE INDICATOR LAMP (4WD)
Component Function Check
INFOID:0000000006598699
1.
4WD MODE INDICATOR LAMP OPERATION CHECK
Check that 4WD mode indicator lamp (4WD) turns on for approximately 1 second after the ignition switch is
turned ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000006598700
1.
CHECK 4WD WARNING LAMP
Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
Does 4WD warning lamp turn ON?
YES
>> Proceed to
.
NO
>> GO TO 2.
2.
CHECK 4WD MODE SWITCH
Perform the trouble diagnosis for 4WD mode switch. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK 4WD MODE INDICATOR LAMP SIGNAL
With CONSULT-III
1.
Start the engine.
CAUTION:
Stop the vehicle.
2.
Change 4WD mode switch to “4WD” from “4WD-V”.
3.
Check “INDICATOR” of CONSULT-III “DATA MONITOR” for “ALL MODE AWD/4WD”.
Does the item on “DATA MONITOR” indicate “4WD”?
YES
>> GO TO 4.
NO
>> Replace 4WD control module. Refer to
DLN-91, "Removal and Installation"
.
4.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
Perform the trouble diagnosis for combination meter power supply circuit. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace the error-detected parts.
4WD WARNING LAMP DOES NOT TURN ON
DLN-83
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SYMPTOM DIAGNOSIS
4WD WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000006359934
4WD warning lamp does not turn ON when the ignition switch is turned to ON.
Diagnosis Procedure
INFOID:0000000006359935
1.
CHECK 4WD WARNING LAMP
Perform the trouble diagnosis for 4WD warning lamp. Refer to
Is the inspection result normal?
YES
>> Check each harness connector pin terminal for malfunction or disconnection.
NO
>> Repair or replace the error-detected parts.
DLN-84
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
4WD WARNING LAMP DOES NOT TURN OFF
4WD WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000006359936
4WD warning lamp does not turn OFF several seconds after the engine started.
Diagnosis Procedure
INFOID:0000000006359937
1.
PERFORM SELF-DIAGNOSIS
With CONSULT-III
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
CHECK 4WD WARNING LAMP
Perform the trouble diagnosis of the 4WD warning lamp. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK 4WD CONTROL MODULE POWER SUPPLY AND GRAUND CIRCUIT
Perform the trouble diagnosis of power supply and ground circuit. Refer to
.
Is the inspection result normal?
YES
>> Check each harness connector pin terminal for malfunction or disconnection.
NO
>> Repair or replace the error-detected parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст