Juke F15 (2012 year). Service Repair Manual — part 62

DEF-32

< DTC/CIRCUIT DIAGNOSIS >

REAR WINDOW DEFOGGER

4.

Check continuity between condenser connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT 2

1.

Disconnect IPDM E/R connectors.

2.

Check continuity between IPDM E/R harness connector and condenser harness connector.

3.

Check continuity between IPDM E/R connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace harness.

6.

CHECK CONDENSER

Refer to

DEF-32, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace condenser. Refer to

DEF-48, "Removal and Installation"

.

7.

CHECK INTERMITTENT INCIDENT

Refer to

GI-42, "Intermittent Incident"

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace harness or connector.

Component Inspection

INFOID:0000000006484488

1.

CHECK CONDENSER

1.

Turn ignition switch OFF.

2.

Disconnect condenser connector.

3.

Check continuity between condenser connector and ground part of condenser.

4.

Check continuity between condenser terminals.

Condenser

Rear window defogger

Continuity

Connector

Terminal

Connector

Terminal

D201

2

D202

1

Existed

Condenser

Ground

Continuity

Connector

Terminal

D201

2

Not existed

IPDM E/R

Condenser

Continuity

Connector

Terminal

Connector Terminal

E11

14

D103

1

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E11

14

Not existed

Condenser

Ground part of

condenser

Continuity

Connector

Terminal

D103

1

Not existed

D202

2

REAR WINDOW DEFOGGER

DEF-33

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace condenser. Refer to

DEF-48, "Removal and Installation"

.

Condenser

Continuity

Connector

Terminal

Connector

Terminal

D103

1

D202

2

Existed

DEF-34

< DTC/CIRCUIT DIAGNOSIS >

DOOR MIRROR DEFOGGER

DOOR MIRROR DEFOGGER

Description

INFOID:0000000006484489

Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.

Component Function Check

INFOID:0000000006484490

1.

CHECK DOOR MIRROR DEFOGGER

1.

Perform IPDM E/R Active Test (“REAR DEFOGGER”) using CONSULT-III.

2.

Touch “ON”.

3.

Check that both side door mirror glasses are getting warmer.

Is the inspection result normal?

YES

>> Door mirror defogger is OK.

NO

>> Refer to

DEF-34, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000006484491

1.

CHECK FUSE

1.

Turn ignition switch OFF.

2.

Check 10A fuse [No.22, located in fuse block (J/B)].

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.

2.

CHECK DOOR MIRROR DEFOGGER CIRCUIT

1.

Disconnect IPDM E/R connector and door mirror (both sides) connector.

2.

Check continuity between IPDM E/R harness connector and door mirror (driver side) harness connector.

3.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to

GI-42, "Intermittent Incident"

.

>> INSPECTION END

IPDM E/R

Door mirror (driver side)

Continuity

Connector

Terminal

Connector

Terminal

E11

14

D29

3

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E11

14

Not existed

DRIVER SIDE DOOR MIRROR DEFOGGER

DEF-35

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

DRIVER SIDE DOOR MIRROR DEFOGGER

Description

INFOID:0000000006484492

Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.

Component Function Check

INFOID:0000000006484493

1.

CHECK DRIVER SIDE DOOR MIRROR DEFOGGER

1.

Perform IPDM E/R Active Test (“REAR DEFOGGER”) using CONSULT-III.

2.

Touch “ON”.

3.

Check that the driver side door mirror glass is getting warmer.

Is the inspection result normal?

YES

>> Driver side door mirror defogger is OK.

NO

>> Refer to

DEF-35, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000006484494

1.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect door mirror (driver side) connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace door mirror glass (driver side). Refer to

MIR-44, "GLASS MIRROR : Removal and Instal-

lation"

NO

>> Repair or replace harness.

(+)

(–)

Condition

Voltage (V)

(Approx.)

Door mirror (driver side)

Connector

Terminal

D29

3

Ground

Rear window defogger
switch

ON

Battery voltage

OFF

0

Door mirror (driver side)

Ground

Continuity

Connector

Terminal

D29

2

Existed

DEF-36

< DTC/CIRCUIT DIAGNOSIS >

PASSENGER SIDE DOOR MIRROR DEFOGGER

PASSENGER SIDE DOOR MIRROR DEFOGGER

Description

INFOID:0000000006484495

Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.

Component Function Check

INFOID:0000000006484496

1.

CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER

1.

Perform IPDM E/R Active Test (“REAR DEFOGGER”) using CONSULT-III.

2.

Touch “ON”.

3.

Check that the passenger side door mirror glass is getting warmer.

Is the inspection result normal?

YES

>> Passenger side door mirror defogger is OK.

NO

>> Refer to

DEF-36, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000006484497

1.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect door mirror (passenger side) connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace door mirror glass (passenger side). Refer to

MIR-44, "GLASS MIRROR : Removal and

Installation"

NO

>> Repair or replace harness.

(+)

(–)

Condition

Voltage (V)

(Approx.)

Door mirror (passenger side)

Connector

Terminal

D8

3

Ground

Rear window defogger
switch

ON

Battery voltage

OFF

0

Door mirror (passenger side)

Ground

Continuity

Connector

Terminal

D8

2

Existed

REAR WINDOW DEFOGGER ON SIGNAL

DEF-37

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

REAR WINDOW DEFOGGER ON SIGNAL

WITH AUTO A/C

WITH AUTO A/C : Description

INFOID:0000000006484498

Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.

WITH AUTO A/C : Component Function Check

INFOID:0000000006484499

1.

CHECK REAR WINDOW DEFOGGER ON SIGNAL

Check that the indicator lamp of rear window defogger switch is illuminated when turning the rear window
defogger switch ON.

Is the inspection result normal?

OK

>> Rear window defogger ON signal is OK.

NG

>> Refer to

DEF-37, "WITH AUTO A/C : Diagnosis Procedure"

.

WITH AUTO A/C : Diagnosis Procedure

INFOID:0000000006484500

1.

CHECK REAR WINDOW DEFOGGER INDICATOR LAMP ON SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect multi display unit connector.

3.

Turn ignition switch ON.

4.

Check voltage between multi display unit harness connector ground.

Is the inspection result normal?

YES

>> Replace multi display unit Refer to

HAC-91, "Removal and Installation"

(4WD models) or

HAC-

188, "Removal and Installation"

(2WD models).

NO

>> Repair or replace harness.

WITHOUT AUTO A/C

WITHOUT AUTO A/C : Description

INFOID:0000000006484501

Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.

WITHOUT AUTO A/C : Component Function Check

INFOID:0000000006484502

1.

CHECK REAR WINDOW DEFOGGER ON SIGNAL

Check that the indicator lamp of rear window defogger switch is illuminated when turning the rear window
defogger switch ON.

Is the inspection result normal?

OK

>> Rear window defogger ON signal is OK.

NG

>> Refer to

DEF-37, "WITHOUT AUTO A/C : Diagnosis Procedure"

.

WITHOUT AUTO A/C : Diagnosis Procedure

INFOID:0000000006484503

1.

CHECK REAR WINDOW DEFOGGER INDICATOR LAMP ON SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect A/C control connector.

3.

Turn ignition switch ON.

4.

Check voltage between A/C control harness connector ground.

Multi display unit

Ground

Condition

Voltage (V)

(Approx.)

Connector

Terminal

M51

27

Rear window defogger switch

ON

Battery voltage

OFF

0

DEF-38

< DTC/CIRCUIT DIAGNOSIS >

REAR WINDOW DEFOGGER ON SIGNAL

Is the inspection result normal?

YES

>> Replace A/C control. Refer to

HAC-239, "Removal and Installation"

(4WD models) or

HAC-304,

"Removal and Installation"

.

NO

>> Repair or replace harness.

WITHOUT A/C

WITHOUT A/C : Description

INFOID:0000000006702995

Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.

WITHOUT A/C : Component Function Check

INFOID:0000000006702996

1.

CHECK REAR WINDOW DEFOGGER ON SIGNAL

Check that the indicator lamp of rear window defogger switch is illuminated when turning the rear window
defogger switch ON.
Is the inspection result normal?

OK

>> Rear window defogger ON signal is OK.

NG

>> Refer to

DEF-38, "WITHOUT A/C : Diagnosis Procedure"

.

WITHOUT A/C : Diagnosis Procedure

INFOID:0000000006702997

1.

CHECK REAR WINDOW DEFOGGER INDICATOR LAMP ON SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect heater control connector.

3.

Turn ignition switch ON.

4.

Check voltage between heater control harness connector ground.

Is the inspection result normal?

YES

>> Replace heater control. Refer to

HAC-331, "Removal and Installation"

.

NO

>> Repair or replace harness.

A/C control

Ground

Condition

Voltage (V)

(Approx.)

Connector

Terminal

M53

4

Rear window defogger switch

ON

Battery voltage

OFF

0

Heater control

Ground

Condition

Voltage (V)

(Approx.)

Connector

Terminal

M47

8

Rear window defogger switch

ON

Battery voltage

OFF

0

REAR WINDOW DEFOGGER SYSTEM

DEF-39

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

REAR WINDOW DEFOGGER SYSTEM

Wiring Diagram - DEFOGGER CONTROL SYSTEM -

INFOID:0000000006484504

For connector terminal arrangements, harness layouts, and alphabets in a

(option abbreviation; if not

described in wiring diagram), refer to

GI-12, "Connector Information/Explanation of Option Abbreviation"

.

JCLWA4248GB

DEF-40

< SYMPTOM DIAGNOSIS >

ALL DEFOGGER SYSTEM DOSE NOT OPERATE

SYMPTOM DIAGNOSIS

ALL DEFOGGER SYSTEM DOSE NOT OPERATE

Description

INFOID:0000000006704079

Rear window defogger and door mirror defogger do not operate when rear window defogger switch operated.

Diagnosis Procedure

INFOID:0000000006704080

1.

CHECK REAR WINDOW DEFOGGER SWITCH

Check rear window defogger switch.
Refer to

DEF-26, "WITH AUTO A/C : Component Function Check"

(With Auto A/C) or

DEF-26, "WITHOUT

AUTO A/C : Component Function Check"

(Without Auto A/C) or

DEF-28, "WITHOUT A/C : Component Func-

tion Check"

(Without A/C).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK REAR WINDOW DEFOGGER RELAY

Check rear window defogger relay.
Refer to

DEF-30, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK REAR WINDOW DEFOGGER

Check rear window defogger.
Refer to

DEF-31, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CONFIRM THE OPERATION

Confirm the operation again.
Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

.

NO

>> GO TO 1.

REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH DOOR MIRROR

DEFOGGERS OPERATE.

DEF-41

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH DOOR
MIRROR DEFOGGERS OPERATE.

Diagnosis Procedure

INFOID:0000000006704081

1.

CHECK REAR WINDOW DEFOGGER

Check rear window defogger.
Refer to

DEF-31, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

.

NO

>> GO TO 1.

DEF-42

< SYMPTOM DIAGNOSIS >

DOOR MIRROR DEFOGGER DOES NOT OPERATE

DOOR MIRROR DEFOGGER DOES NOT OPERATE

BOTH SIDES

BOTH SIDES : Description

INFOID:0000000006704082

Both door mirror defoggers do not operate.

BOTH SIDES : Diagnosis Procedure

INFOID:0000000006704083

1.

CHECK REAR WINDOW DEFOGGER

Check rear window defogger.
Refer to

DEF-31, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK DOOR MIRROR DEFOGGER

Check door mirror defogger.
Refer to

DEF-34, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

.

NO

>> GO TO 1.

DRIVER SIDE

DRIVER SIDE : Description

INFOID:0000000006704084

Driver side door mirror defogger does not operate but passenger side door mirror defogger operates.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000006704085

1.

CHECK DRIVER SIDE DOOR MIRROR DEFOGGER

Check driver side door mirror defogger.
Refer to

DEF-35, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

.

NO

>> GO TO 1.

PASSENGER SIDE

PASSENGER SIDE : Description

INFOID:0000000006704086

Passenger side door mirror defogger does not operate but driver side door mirror defogger operates.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000006704087

1.

CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER.

DOOR MIRROR DEFOGGER DOES NOT OPERATE

DEF-43

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

Check passenger side door mirror defogger.
Refer to

DEF-36, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

.

NO

>> GO TO 1.

DEF-44

< SYMPTOM DIAGNOSIS >

ON IS NOT DISPLAYED WHEN PRESSING REAR WINDOW DEFOGGER

SWITCH BUT IT IS OPERATED

ON IS NOT DISPLAYED WHEN PRESSING REAR WINDOW DEFOGGER
SWITCH BUT IT IS OPERATED

Diagnosis Procedure

INFOID:0000000006704089

1.

CHECK MULTI DISPLAY UNIT FUNCTION

Check that the multi display unit is operating normally.
• Auto A/C (4WD models). Refer to

HAC-44, "Work Flow"

.

• Auto A/C (2WD models). Refer to

HAC-135, "Work Flow"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-42, "Intermittent Incident"

.

NO

>> GO TO 1.

REAR WINDOW DEFOGGER INDICATOR DOES NOT ILLUMINATE

DEF-45

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

REAR WINDOW DEFOGGER INDICATOR DOES NOT ILLUMINATE

Diagnosis Procedure

INFOID:0000000006704090

1.

CHECK A/C CONTROL AND HETER CONTROL SWITCH (REAR WINDOW DEFOGGER SWITCH)

Check that rear window defogger operates.
Is the inspection result normal?

YES

>> Replace A/C contorol(with Auto A/C) and heter control(without A/C) switch (rear window defogger

switch).

NO

>> Check rear window defogger system. Refer to

DEF-25, "Work Flow"

DEF-46

< REMOVAL AND INSTALLATION >

FILAMENT

REMOVAL AND INSTALLATION

FILAMENT

Inspection and Repair

INFOID:0000000006484456

INSPECTION

1.

When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.

2.

Attach probe circuit tester (in Volt range) to middle portion of
each filament.

3.

If a filament is burned out, circuit tester registers 0 or battery
voltage.

4.

To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.

REPAIR

REPAIR EQUIPMENT

• Conductive silver composition (Dupont No. 4817 or equivalent)

SEL122R

SEL263

SEL265

FILAMENT

DEF-47

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

DEF

N

O

P

• Ruler 30 cm (11.8 in) long
• Drawing pen
• Heat gun
• Alcohol
• Cloth

REPAIRING PROCEDURE

1.

Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.

2.

Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.

3.

Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.

4.

After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.

5.

Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.

PIIA0215E

SEL012D

SEL013D