Nissan Versa Sedan. Manual — part 724
SIDE AIR BAG MODULE
SR-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SIDE AIR BAG MODULE
Removal and Installation
INFOID:0000000009266929
REMOVAL
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seatback repair. It can lead to
personal injury if the side air bag should accidentally deploy.
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least three
minutes.
• Handle the side air bag module carefully. During disassembly, always hold the side air bag module,
do not let it hang by the wire harness.
• Always place the side air bag module with the deployment side facing upward.
• Always work from the side or back of the seatback assembly, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
• Replace the side air bag module if it has been dropped or sustained an impact.
• Do not insert any objects into the side air bag module.
• Do not attempt to disassemble the air bag module.
• Do not expose the side air bag module to temperatures exceeding 90
°C (194°F).
• Do not expose the side air bag module to any oil, grease, detergent or water.
• During disassembly, do not damage the seatback cover, chutes, connectors, retainers, clips, module
harness or the side air bag module.
NOTE:
• If the vehicle has been involved in a collision and the side air bag has deployed, the front seatback assembly
must be replaced.
• For side air bag module removal and installation, seatback trim and seatback pad must be released from the
seatback frame for access.
1. Remove the driver or passenger seat assembly. Refer to
SE-17, "DRIVER SIDE : Removal and Installa-
2. Disassemble the seatback, release the seatback trim and seatback pad as an assembly, then remove
side air bag module from the seatback. Refer to
SE-29, "DRIVER SIDE : Disassembly and Assembly"
SE-40, "PASSENGER SIDE : Disassembly and Assembly"
(PASSENGER SIDE).
NOTE:
The side air bag module is removed from the seat frame, then through the sewn in chute, as part of the
seatback cover and pad disassembly procedure.
INSTALLATION
Installation is in the reverse order of removal.
SR-22
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Exploded View
INFOID:0000000009266930
Removal and Installation
INFOID:0000000009266931
REMOVAL
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait three min-
utes or more.
• Do not use the air tools or electric tools for servicing.
CAUTION:
• Do not impact the crash zone sensor.
• Replace the crash zone sensor if it has been dropped or sus-
tained an impact.
• Replace the crash zone sensor of deployed driver air bag and
deployed passenger air bag.
1. Remove the crash zone sensor nut, then remove the bracket
and crash zone sensor from radiator support bracket in front of
vehicle.
2. Disconnect the harness connector from the crash zone sensor.
3. Remove crash zone sensor.
INSTALLATION
1.
Crash zone sensor
2.
Bracket
A.
Nut
Front
AWHIA0346GB
JMHIA0009ZZ
CRASH ZONE SENSOR
SR-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
Installation is in the reverse order of removal.
CAUTION:
• Make sure the locating pin on crash zone sensor is aligned with the cutout hole of the radiator sup-
port bracket before tightening nut.
• Do not use the old nut after removal, replace with new nut.
• Do not damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to
SRC-15, "CONSULT Function (AIR BAG)"
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
SR-24
< REMOVAL AND INSTALLATION >
SIDE AIR BAG (SATELLITE) SENSOR
SIDE AIR BAG (SATELLITE) SENSOR
Removal and Installation
INFOID:0000000009266932
Side air bag (satellite) sensor
Front door (satellite) sensor
WARNING:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least three
minutes.
• Do not use air tools or electric tools for servicing.
CAUTION:
• Do not use old nuts after removal; replace with new nuts.
• Do not cause impact to the side air bag (satellite) sensor by dropping etc. Replace the side air bag
(satellite) sensor if it has been dropped or sustained an impact.
AWHIA0350GB
1.
Side air bag (satellite) sensor harness slide
double locking type connector
2.
Side air bag (satellite) sensor A.
Side air bag (satellite) sensor nut
Front
AWHIA0351GB
1.
Front door (satellite) sensor harness
connector
2.
Front door (satellite) sensor
A.
Front door (satellite) sensor nuts
Front
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст