Nissan Versa Sedan. Manual — part 128
WHEEL SENSOR
BRC-105
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Do not twist front wheel sensor harness when installing front
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that front wheel sensor harness is not
twisted after installation.
REAR WHEEL SENSOR
REAR WHEEL SENSOR : Exploded View
INFOID:0000000009267675
REAR WHEEL SENSOR : Removal and Installation
INFOID:0000000009267676
CAUTION:
• Be careful not to damage wheel sensor edge and sensor rotor teeth.
• When removing the front or rear wheel hub, first remove the wheel sensor from the wheel hub. Fail-
ure to do so may result in damage to the wheel sensor wires, making the sensor inoperative.
• Pull out the wheel sensor, being careful to turn it as little as possible. Do not pull on the wheel sen-
sor harness.
• Before installation, check if foreign objects, such as iron fragments, are adhered to the pick-up part
of the sensor or to the inside of the hole in the wheel hub for the wheel sensor, or if a foreign object
is caught in the surface of the mating surface for the sensor rotor. Fix as necessary and then install
the wheel sensor.
REMOVAL
1. Remove rear wheel sensor from back plate.
2. Remove rear wheel sensor harness from the vehicle.
JPFIC0209ZZ
1.
Rear wheel sensor (LH)
2.
Rear wheel sensor harness connector (LH)
Front
AWFIA0866GB
BRC-106
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
WHEEL SENSOR
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not twist rear wheel sensor harness when installing rear
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that rear wheel sensor harness is not twisted
after installation.
JPFIC0209ZZ
SENSOR ROTOR
BRC-107
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SENSOR ROTOR
FRONT SENSOR ROTOR
FRONT SENSOR ROTOR : Removal and Installation
INFOID:0000000009267677
REMOVAL
The front wheel sensor rotor is an integral part of the wheel hub and bearing assembly and can not be
replaced individually. When replacing the front wheel sensor rotor replace the hub and bearing assembly.
FAX-9, "Removal and Installation"
INSTALLATION
FAX-9, "Removal and Installation"
REAR SENSOR ROTOR
REAR SENSOR ROTOR : Removal and Installation
INFOID:0000000009267678
REMOVAL
1. Remove the brake drum. Refer to
.
2. Remove the sensor rotor from brake drum. Refer to
BR-43, "Disassembly and Assembly"
.
CAUTION:
Do not reuse rear sensor rotor.
INSTALLATION
Installation is in the reverse order of removal.
BRC-108
< REMOVAL AND INSTALLATION >
[VDC/TCS/ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Exploded View
INFOID:0000000009267679
Removal and Installation
INFOID:0000000009267680
CAUTION:
Be careful of the following:
• Before servicing, disconnect the battery cable from negative terminal.
• To remove brake tubes, use a suitable tool (flare nut wrench) to prevent flare nuts and brake tubes
from being damaged. To install, use suitable tool (flare nut torque wrench).
• Do not apply excessive impact to ABS actuator and electric unit (control unit), such as by dropping
it.
• Do not remove and install ABS actuator and electric unit (control unit) by holding harness.
• After work is completed, bleed air from brake tubes. Refer to
BR-12, "Bleeding Brake System"
.
• After installing harness connector on the ABS actuator and electric unit (control unit), make sure
connector is securely locked.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Disconnect battery cable from negative terminal. Refer to
PG-63, "Removal and Installation"
.
2. Remove A/C high-pressure pipe. Refer to
HA-35, "Removal and Installation"
.
3. Remove A/C low-pressure flexible hose. Refer to
HA-33, "Removal and Installation"
4. Disconnect the harness connector from the ABS actuator and electric unit (control unit).
1.
ABS actuator and electric unit (con-
trol unit)
2.
ABS actuator and electric unit (con-
trol unit) harness connector
3.
Bushing
4.
Bracket
A.
To master cylinder secondary side
B.
To master cylinder primary side
C.
To front wheel cylinder (LH)
D.
To rear wheel cylinder (RH)
E.
To rear wheel cylinder (LH)
F.
To front wheel cylinder (RH)
JPFIC0214GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст